User Manual for Continental models including: QXMFGE04, SY5QXMFGE04, SVI-QXMFGE04 Token and Token Plus Fob, SVI-QXMFGE04, Token and Token Plus Fob

Spezifikationsformular in Deutsch mit Struktur

Eunsoory Berger-Münch PM

User Manual

Continental Automotive Korea Ltd. QXMFGE04 SY5QXMFGE04 SY5QXMFGE04 qxmfge04


File Info : application/pdf, 6 Pages, 208.65KB

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=6202400
Document :

User Manual for TOKEN/TOKEN PLUS Fob

Project : Model name : Version: Date:

QX 24MY FOB 3B/4B
SVI-QXMFGE04
1.0 Oct. 13. '22

Engineering change order-No.:

Design Freeze No.:

Number of pages:

6

Filename:

CASCO

Identification No. :

Contents list

1. 1.1 1.2 1.2.1 1.2.2 1.2.3 1.3 2 3

System configulation Scope of SMART KEY SYSTEM Short description of the SYSTEM General Definition of SMART KEY Wireless Communication Concept Description System Overview / Block Diagram Smart Key Fob button operation FCC/IC Compliance Statement

Page
3 3 3 3 3 3 4 5 6

Editor : KS.Kim

Document name

Version: 1.0

ECO / DF No.

Jul. 22. 2022

Identification No. : Document No.

File:

Project code Page 2 / 6

1. System configulation
1.1 Scope of SMART KEY SYSTEM The System offers the following features:
· passive access for two doors, driver side and passenger side as well as trunk/tailgate · passive start after interior detection of the SMART KEY FOB (without interior trunk and hat
shelf detection) · LF-RF communication · passive access trunk/tailgate via the trunk lid switch at the trunk · max. 4 SMART KEY FOBs can be handled by the system · communication to the engine management system via a single line interface · communication to the ESCL via a single line interface
1.2 Short description of the SYSTEM

1.2.1 General Definition of SMART KEY
The SMART KEY system is a system that allows the user to access and operate a vehicle in a very convenient way. To access the vehicle no traditional key or remote control unit is needed.
The user carries a SMART KEY FOB which itself does not require any conscious actions by the user (e.g. operate a button).
After being triggered the vehicle sends out a request in a limited range. If the SMART KEY FOB receives this request, it automatically sends a response to the vehicle. Then the system decides whether to perform a particular action (unlocking, locking...) or remain inactive.

1.2.2 Wireless Communication
Electromagnetic waves are used to exchange information between the vehicle and the SMART KEY FOB. Both, vehicle and SMART KEY FOB are equipped with a transmitter, a receiver and several antennas.

1.2.3 Concept Description
With this concept it is possible to have a set of interior antennas that covers the vehicle's interior and a set of exterior antennas that covers the vehicle's exterior. For an unambiguous separation between the vehicle's interior and exterior it is sufficient that at least one area is covered exactly by the corresponding operating ranges of the antennas.

The functions of the SMART KEY system have to be provided in a clearly defined and limited range. For the up-link from the vehicle to the SMART KEY FOB, a magnetic field

Editor : KS.Kim

Document name

Version: 1.0

ECO / DF No.

Jul. 22. 2022

Identification No. : Document No.

File:

Project code Page 3 / 6

with a frequency of 125 kHz and ASK modulation is used. Inductive antennas in and at the vehicle radiate the electromagnetic energy.
Technical aspects of 125 kHz ­ magnetic field: · virtually no reflections, · cubical decrease of field strength  allows good range control, · released frequency band (ISM), · high penetration, · low quiescent current demand due to 125 kHz input stage (SMART KEY FOB), · less sensitive for detuning compared to higher frequency.
For the down-link from the SMART KEY FOB to the vehicle, the standard radio frequency (RF) is used (similar to the classic remote control functions) with FSK modulation.

1.3 System Overview / Block Diagram

ECU sends LF challenge via exterior antenna

ID tag sends identification code to RF receiver

Doors are unlocked automatically
User pulls open the door
L F

Figure 1: Principle of Communication

Editor : KS.Kim

Document name

Version: 1.0

ECO / DF No.

Jul. 22. 2022

Identification No. : Document No.

File:

Project code Page 4 / 6

2 Smart Key Fob button operation
Lock Unlock HOLD (Trunk) Panic

You can lock, unlock, trunk and hold your vehicle with this remote transmitter.

Lock -

When you push this button, all the doors will be locked. You can not lock any of the doors with this remote transmitter if any door is open or the key is in the fob holder.

Unlock -

When you push this button, all the doors will be unlocked. You can not unlock any of the doors with this remote transmitter if any door is open or the key is in the fob holder.

HOLD(Trunk) - When you push this button and hold more than 1 second, the trunk will be opened.

Panic - When you push this button for about 1second, Horn will alarm

Editor : KS.Kim

Document name

Version: 1.0

ECO / DF No.

Jul. 22. 2022

Identification No. : Document No.

File:

Project code Page 5 / 6

3 FCC/IC Compliance Statement FCC Compliance Statement.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including
interferencethat may cause undesired operation.

Do Not

Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void

user's authority to operate the equipment.
IC Compliance Statement.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage
est susceptible d'en compromettre le fonctionnement.

Editor : KS.Kim

Document name

Version: 1.0

ECO / DF No.

Jul. 22. 2022

Identification No. : Document No.

File:

Project code Page 6 / 6


Eunsoory Adobe PDF Library 15.0