Babylo Racer 500 Baby Walker

Care

Maintenance

This product requires regular maintenance to keep it in good working order. Regularly check all parts of the product to ensure that they are operating correctly and for signs of wear or damage. Do not use this product if any part is broken, torn or missing and use only spares provided by the manufacturer.

Cleaning

Seat pad: Hand wash or spot clean. Use mild soap or upholstery shampoo. Wash separately. NEVER use bleach. Dry in shade thoroughly before reuse and avoid direct heat and sunlight. Do not iron. Do not dry clean.

Frame: Wipe frame with soft clean cloth and mild soap. NEVER use bleach. NEVER use abrasive, ammonia based, bleach based or spirit type cleaners. Store walker in a dry location away from any heat sources, and not in the sun. Ensure the product is fully dry before use or storage.

Product Specifications

CE Mark: CE

Parts List

Please check all parts are present before assembly. Refer to the following list:

• Part A: Base Unit (x1)
• Part B: Seat Unit (x1)
• Part C: Seat Unit Back Panel (x1)
• Part D: Toy Tray (x1)
• Part E: Anti-slip Pads (x6)
• Part F: Car Mirrors (x2)
• Part G: Rear Wing (x1)
• Part H: Car Wheels (x4)
• Part I: Universal Wheels (x2)
• Tools Required: Phillips-head screwdriver (not included)

Safety Warnings

CAUTION: Read these instructions carefully before assembly and use and keep for future reference. The child may be hurt if you do not follow these instructions.

WARNING: The walker is not intended for babies that can already walk unassisted.

WARNING: Do not use the walker if it is damaged or broken.

WARNING: Do not use until the baby can sit upright by itself.

WARNING: Clean friction components regularly to maintain stopping performance.

WARNING: Never leave the child unattended. Always keep child in view while in walker.

WARNING: Use only on flat surfaces free of objects that could cause the walker to tip over.

WARNING: To avoid burns, keep the child away from hot liquids, ranges, radiators, space heaters, fire places etc.

WARNING - STAIR HAZARD: Avoid serious injury or death. Block stairs/steps securely before using walker.

Complies with EN 1273:2005 and ASTM F9077-12.

Battery Safety

ATTENTION! BATTERY SAFETY: KEEP FOR FUTURE REFERENCE. BATTERIES NOT INCLUDED.

CAUTION: To prevent possible battery leakage, follow these guidelines:

• Alkaline batteries are recommended for longer battery life.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon zinc) or rechargeable batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted correctly by matching the + and - polarity markings.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Dispose of exhausted batteries properly.
• Remove batteries when product is stored for long periods of time.

Use a small Phillips-head screwdriver to open the battery compartment door on the toy. Insert the battery as indicated inside the battery door and re-attach the battery compartment door with screw.

Assembly Instructions

IMPORTANT: Adult assembly required. Read all instructions before assembly and use of the product.

This baby walking frame is intended for children who can sit unaided, approximately from 6 months. It is not intended for children weighing more than 12kg and/or more than 78cm in height.

Take care when unpacking and during assembly. Dispose of all packaging materials carefully after assembly. Regularly check that all fittings remain tight. Tighten if required. Inspect the product before all assembly and periodically during use. Never use this product if there is any loose or missing fasteners, joints or broken parts. Any additional or replacement parts should only be obtained from the manufacturer or distributor. Never substitute parts.

Step 1: Attach Wheels

1. Unpack all contents and check that all parts are present before starting assembly. Place walker (A) on a solid flat surface with the bottom of the base facing upwards.

Insert the pins of the universal wheels (I) into their housing located at the front of the walker. Press until they click into place.

Insert the directional wheels (I) into their housing located at the rear of the walker. Ensure to align the shape of the mount with the housing before inserting wheels. Press until they click into place. Pull on wheels to ensure they are properly inserted.

WARNING! Ensure you have installed wheels correctly before continuing.

Diagram description: Shows two types of wheels being inserted into the base of the walker. Universal wheels (I) go into the front, directional wheels (I) go into the rear. Arrows indicate pushing until a click is heard.

Step 2: Attach Seat Unit Back Panel

2. Turn walker over with the top of the walker facing up. Assemble the seat unit back panel (C) into the allocated slots. Push firmly until the panel clicks into place.

Diagram description: Shows the seat unit back panel (C) being slotted into the main walker frame. An arrow indicates pushing until a click is heard.

Step 3: Install Seat Unit

3. Push the crotch portion of the seat unit (B) inside out to form the seat. IMPORTANT: The black and white checker board fabric should be on the inside of the seat unit.

Insert the 8 tabs located on the seat unit into the slots dotted around the seat ring.

Diagram description: Shows the seat unit (B) being prepared and then its 8 tabs being inserted into corresponding slots around the walker's seat area.

Step 4: Secure Seat Unit

4. Turn walker upside down and pull tabs firmly from underneath the walker until tabs are completely through slots. Ensure all tabs are secure before continuing.

IMPORTANT: Push down firmly on the seating area of the seat unit to ensure it is securely assembled.

WARNING! Ensure you have installed the seat unit correctly before continuing.

Diagram description: Shows the underside of the walker where the seat unit tabs are pulled through. An arrow indicates pushing down on the seat area to secure it.

Step 5: Attach Anti-slip Pads

5. Turn walker over and attach anti-slip pads (E) to the attachment points on the baby walker base. Push down firmly until secure. Never attempt to force the anti-slip pads onto the attachment points. Pulling anti-slip pads out from holes once fitted could cause damage.

Diagram description: Shows the underside of the walker base with anti-slip pads (E) being attached to specific points. Arrows indicate pushing down firmly.

Step 6: Attach Top Tray and Rear Wing

6. Raise the baby walker top tray as shown until it clicks into place. Note: The baby walker has 3 height positions. Refer to page 8 for more details.

Insert rear wing (G) connection points into the allocated holes on the rear side of the walker top tray. Push down firmly until it clicks into place.

Diagram description: Shows the top tray being lifted into place with a click. Then, the rear wing (G) is shown being attached to the rear of the top tray with arrows indicating insertion until a click.

Step 7: Attach Car Wheels

7. Push car wheels (H) firmly onto spoke end until you hear a click. Repeat for all 4 wheels.

WARNING! Ensure wheels are secure before continuing.

Diagram description: Shows a car wheel (H) being pushed onto a spoke on the walker base until a click is heard. This is repeated for all four wheels.

Step 8: Insert Car Mirrors

8. Insert the car mirrors (F) into the allocated slots either side of the walker top tray. Push down firmly until they click into place.

Diagram description: Shows car mirrors (F) being inserted into slots on the sides of the walker's top tray until they click.

Step 9: Install Batteries in Toy Tray

9. The toy tray (D) requires 2 x “AA” batteries (not included). Use a screwdriver to unfasten the battery cover. Insert batteries. Secure the battery cover back into position.

WARNING! Remove batteries before storing the toy tray and walker.

Diagram description: Shows the underside of the toy tray (D) with a battery compartment cover being opened with a screwdriver. AA batteries are shown being inserted, and the cover is being replaced.

Step 10: Attach Toy Tray

10. Once batteries are installed, attach the toy tray (D) to the walker. The tray will click once secure.

Diagram description: Shows the toy tray (D) being attached to the walker, aligning with attachment points, until it clicks into place.

Toy Tray Operation

Push switch to ON located on the bottom of the toy tray to activate sound and lights. Press the various buttons for sounds and melodies. Push switch to OFF to turn off sound and lights.

Diagram description: Shows the toy tray with buttons and a switch. Arrows indicate pushing the switch to ON for sound and lights, and pressing buttons for features. The switch is then shown being moved to OFF.

Height Adjustment

The baby walker has 3 height positions. To adjust height, remove the baby from the walker.

Turn the safety button lengthwise and press the safety button up until the mechanism is released. Adjust to the desired height.

WARNING! When the position has been selected, check the safety button is turned 90° to prevent accidental release.

WARNING! Do not adjust height when the baby is in the walker.

WARNING! Ensure the mechanism is locked before placing the baby in the walker.

To fold the walker, turn the safety button lengthwise and press the safety button up until the mechanism is released. Push the walker down to a folded position.

Diagram description: Shows a close-up of the height adjustment mechanism. It illustrates turning a safety button, pressing it up to release, adjusting the height, and then checking the button is turned 90° to lock. It also shows the folding mechanism.

Disposal Information

The crossed-out bin symbol ?️ on the appliance indicates that the product, at the end of its life, must be disposed of separately from domestic waste. This can be done by taking it to a separate waste disposal site for electric and electronic appliances, or by returning it to your dealer when purchasing a similar appliance. The user is responsible for taking the appliance to a special waste disposal site at the end of its life.

If the disused appliance is collected correctly as separate waste, it can be recycled, treated, and disposed of ecologically. This avoids a negative impact on both the environment and health and contributes towards the recycling of the product's materials.

For further information regarding waste disposal services available, contact your local waste disposal agency or the shop where you bought the appliance.