Instructions for i-PRO models including: WV-Q117A Ceiling Mount Bracket, WV-Q117A, Ceiling Mount Bracket, Mount Bracket, Bracket
WV-Q117A Operating Instructions | i-PRO Products
WV-Q117A | Function Extension Kits | i-PRO Security System
Ceiling Mount Bracket Instructions
Model No. WV-Q117A
INSTALLATION
1 Decide where to install the camera and open a 60 mm {2-3/8"} hole in the ceiling.
C beam
Ceiling
Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Ns0513-3042 PGQX1355WA
Printed in China
FEATURES
Ceiling hanging bracket: This bracket can be used to hang the camera from a suspended ceiling or other location that is not strong enough to hold a screw.
2 Setting up the Mounting board.
For suspended ceilings (1) Prepare a Mounting board long enough to
span the distance between the C-beams, and cut a 60 mm {2-3/8"} hole in it that matches the hole in the ceiling. (2) Use the template (provided) to cut four 6 mm {1/4"} holes (in four positions) in the mounting board. For structurally strong ceilings Prepare the mounting board by cutting a 60 mm {2-3/8"} hole in it.
M beam
60 mm in diameter {2-3/8"}
Mounting board
Ceiling board Mounting board
Ceiling board
3 Attach the Ceiling Mount Ring (provided) to the Mounting board Screws are not provided. Align it with the position the camera will be installed.
7For suspended 7For structurally
ceilings
strong ceilings
Ceiling Mount Ring (provided)
Ceiling Mount Ring (provided)
Wood screws (not provided)
PRECAUTIONS
· Fasten the bracket to a ceiling strong enough to support the camera weight (approx. 2.9 kg {6.38 lbs}).
· Wipe the bracket regularly using a soft and dry cloth, or a cloth moistened with a water solution of an ordinary kitchen detergent.
· Do not use chemicals for cleaning the enclosure as it may damage the surface.
· All the necessary steps required for installing this product must be taken by a qualified service person or system installer.
· Be sure to use the aniti-fall wire.
· Do not use this bracket except with suitable cameras.
· Follow all applicable local and national electrical, fire and safety codes when installing the camera with this ceiling mount bracket.
The model numbers in this Operating Instructions are shown without suffix.
4 Installing the Mounting board.
For suspended ceilings Align it with the hole in the ceiling and lay it across the two C-beams. For structurally strong ceilings Align it with the hole in the ceiling and attach it.
5 Remove the Mounting Screw (M3, provided), pull up the Camera Mounting Base off the camera, and turn the camera counterclockwise.
M4 Screws (not provided)
Mounting Screw
Rotate
15°
6 Remove the two Lock Lug Fixing Screws and replace the Lock Lug with L-type. Retighten the two Lock Lug Fixing Screws (refer to the right figure). Recommended tightening torque: 0.68 N·m {0.51 lbf·ft}
Remove the Camera Mounting Base by pulling up.
Lock Lug Fixing Screws
Lock Lug Fixing Screws
Lock Lug
L-type Base Lug (provided)
7 Remove the two Lock Lug Fixing Screws and replace the Lock Lug with L-type. Retighten the two Lock Lug Fixing Screws (refer to the right figure). Recommended tightening torque: 0.68 N·m {0.51 lbf·ft}
Lock Lug Fixing Screws Lock Lug
8 Pass the power cord and video cables of the Camera Mounting Base through the hole in this bracket, and fasten it to the bracket with the four M4-L8 Screws (provided). Recommended tightening torque: 1.56 N·m {1.16 lbf·ft}
L-type Lock Lug (provided)
Camera Mounting Base
M4-L8 Screws (provided)
9 Fit the Slot Masking Cover (provided) over the bracket, insert the Hexagon Socket Head Screws (M3, provided) into their holes, and fasten the Ceiling Mount Ring (provided) with the two nuts (M3, provided). Recommended tightening torque (M3) : 0.68 N·m {0.51 lbf·ft} Recommended tightening torque (M4) : 1.56 N·m {1.16 lbf·ft}
Slot Masking Cover (provided) M3 Screw (provided)*2 Hexagon Socket Head Screw (M4, provided)
Ceiling
*1 Use two nuts. *2 Fasten finally.
Nut (M4, provided)
10 Suspend the Fall Prevention Wire for the camera from the Camera Mounting Base.
Note: Make sure that the wire matches the Fall Prevention Wire Fixing Angle.
* The bracket is not shown in the illustrations.
Ring of the Fall Prevention Wire
11 Attach the camera to the Camera Mounting Base, turn the camera clockwise, and tighten the Mounting Screw (M3, provided). Recommended tightening torque: 0.68 N·m {0.51 lbf·ft}
Rotate 15
Camera Mounting Bracket L-type Lock Lug (provided)
Mounting Screw
12 Place the Decoration Cover for the bracket on the camera. Then, pull up the Slot Masking Cover (provided).
Decoration Cover
13 Attach the Fall Prevention Clip (provided) to the anchor bolt. Attach the Fall Prevention (provided) to the bracket and the Fall Prevention Angle Clip. Note: Two spacer nuts are necessary for the anchor bolt.
Instructions for the Fall Prevention Clip (provided)
1. Remove the Fall Prevention Wire from the Fall Prevention Clip.
2. Insert anchor bolt from side .
3. Fold side down over side .
4. Suspend the Fall Prevention Angle Clip from the other end of the
Fall Prevention Wire.
above
Side
1 Insert 2 Remove
3 fold down
Fall Prevention Wire Side
Anchor Bolt
below
4
Anchor Bolt
Fall Prevention Clip (provided)
Fall Prevention Wire (provided)
Fall Prevention Clip (provided)
Spacer nuts
Existing anchor bolt
14 Cover the bracket with the Heat Insulator (provided).
Heat insulator (provided)
Heat insulator (provided)
SPECIFICATIONS
Ambient Operating Temperature: Dimensions:
Weight:
10°C - +50°C {14°F 122°F} 120 (diameter) × 202 (D) mm {4-3/4" (diameter) × 7-61/64" (D) mm} 720 g {1.59 lbs}
Weight and dimensions indicated are approximate. Specifications are subject to change without notice.
STANDARD ACCESSORIES
Fall Protection Wire..........................................1 pc. Fall Prevention Clip..........................................1 pc. Ceiling Mounting Ring .....................................1 pc. L-type Base Lug ..............................................1 pc. L-type Lock Lug...............................................1 pc. Slot Masking Cover..........................................1 pc. Hexagon Socket Head Screw (M4) ...............2 pcs.
Wrench for Hexagon Socket Head Screw.......1 pc. Nut (M4) .........................................................4 pcs. Screw (M3).....................................................2 pcs. Screw (M4-L8) ...............................................4 pcs. Template..........................................................1 pc. Heat Insulator ..................................................1 pc.
Slot Masking Cover (provided)
For U.S. and Canada: i-PRO Americas Inc.
For Europe and other countries: i-PRO EMEA B.V. https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Acrobat Distiller 7.0.5 for Macintosh