User Manual for NetComm models including: NTC-140 GPS Week Roll Over Patch
Installation instructions The procedure for installing this patch is the same as that of installing a firmware update on the router. Follow the steps below: Note – In order to install the patch, you must be logged in to the router with the root manager account (refer to the User Guide for more detail).
Installation instructions. The procedure for installing this patch is the same as that of installing a firmware update on the router. Follow the.
File Info : application/pdf, 6 Pages, 187.58KB
DocumentDocumentPatch Release Notes NTC-140 GPS Week Roll Over Patch Doc No. FR01158 Important notice This device, like any wireless device, operates using radio signals which cannot guarantee the transmission and reception of data in all conditions. While the delay or loss of signal is rare, you should not rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data loss, or other loss. NetComm Wireless accepts no responsibility for any loss or damage resulting from errors or delays in transmission or reception, or the failure of the NetComm NTC-140 Series router to transmit or receive such data. Safety and hazards Warning Do not connect or disconnect cables or devices to or from the USB port, SIM card tray, Ethernet port or the terminals of the power connector in hazardous locations such as those in which flammable gases or vapours may be present, but normally are confined within closed systems; are prevented from accumulating by adequate ventilation; or the location is adjacent to a location from which ignitable concentrations might occasionally be communicated. Copyright Copyright© 2019 NetComm Wireless Limited. All rights reserved. The information contained herein is proprietary to NetComm Wireless. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of NetComm Wireless. Trademarks and registered trademarks are the property of NetComm Wireless Limited or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product. Note This document is subject to change without notice. NTC-140 GPS Week Roll Over Patch Patch Release Notes FR01158 v1.0 28 May 2019 2 of 6 © NetComm 2019 Document history This document relates to the following products: - NTC-140-02 - NTC-140W-01 - NTC-140W-01-ATT - NTC-140W-01 Sprint - NTC-140W-01 VCCU - NTC-140W-01-ACCU - NTC-140W-01 CCR - NTC-140W-01-VZW - NTC-140W-01 Rogers - NTC-140W-02 - NTC-140W-02 Voda EU - NTC-140W-02 CC - NTC-140W-02-T VER. DOCUMENT DESCRIPTION v 1.0 Initial document release Table i. - Document revision history DATE 28 May 2019 NTC-140 GPS Week Roll Over Patch Patch Release Notes FR01158 v1.0 28 May 2019 3 of 6 © NetComm 2019 Contents Release information ...........................................................................................................................................................5 Installation instructions..................................................................................................................................................................................................5 Release history...................................................................................................................................................................6 v1.2 Initial release........................................................................................................................................................................................................6 NTC-140 GPS Week Roll Over Patch Patch Release Notes FR01158 v1.0 28 May 2019 4 of 6 © NetComm 2019 Release information ITEM Product code(s) Patch file name MD5 checksum Date DETAILS NTC-140-02 NTC-140W-01 NTC-140W-01-ATT NTC-140W-01 Sprint NTC-140W-01 VCCU NTC-140W-01-ACCU NTC-140W-01 CCR NTC-140W-01-VZW NTC-140W-01 Rogers NTC-140W-02 NTC-140W-02 Voda EU NTC-140W-02 CC NTC-140W-02-T sierra-mc73xx-gps-rollover_1.2_arm.ipk 11A96B3E7B7C38566241E0B5733C632F 28 May 2019 Installation instructions The procedure for installing this patch is the same as that of installing a firmware update on the router. Follow the steps below: Note In order to install the patch, you must be logged in to the router with the root manager account (refer to the User Guide for more detail). 1 Power on the router and log in using the root account. 2 Select the System item from the top menu bar, select the System configuration item from the menu on the left and then select the Upload menu item. 3 Under the File uploads section, click the Choose a file button. Locate the patch file on your computer and click Open. 4 Click the Upload button. The patch file is uploaded to the storage on the router. 5 The uploaded patch file is listed in the Uploaded files section. Click the Install link next to the patch file to begin installing it then click OK on the confirmation window that appears. The installation is complete. You can view the installed packages by navigating to System > System configuration > Package manager. NTC-140 GPS Week Roll Over Patch Patch Release Notes FR01158 v1.0 28 May 2019 5 of 6 © NetComm 2019 Release history v1.2 Initial release Enhancements The Global Positioning System provides positioning fixes and timing information to GPS receivers (such as the MC73xx module). The timing information includes a 'week' component represented as an integer value from 01023. This value will 'roll over' on 03 November 2019. As a result, the time reported to customer applications by MC73xx modules will be incorrect. (Note: Positioning fixes will not be affected.) This patch ensures that the time reported to applications is correct. NTC-140 GPS Week Roll Over Patch Patch Release Notes FR01158 v1.0 28 May 2019 6 of 6 © NetComm 2019Microsoft Word for Office 365