User Manual

SAFETY CAUTION

• Do not use earphones & speaker while driving; please observe national and regional regulations.
• Ensure all equipment and accessories are safely stored from children or pets.
• Do not use the product in extreme temperatures either below 14 degrees Fahrenheit or above 113 degrees Fahrenheit, as this may cause deformations, reduce the charging capacity of the device, and shorten the service life of the product.
• Do not use wet equipment; liquid can cause severe damage to the equipment.
• Please do not use wet hands while operating the equipment, as it may cause damage and is not covered under the scope of the warranty.
• If the earphones & speaker play at a high volume for a long period of time, your hearing may become impaired. It is suggested to use the lowest volume of the phone.

TRUE WIRELESS EARBUDS OPERATION INSTRUCTIONS

Initial Earbuds Set Up/Pairing

1. Once both earbuds are removed from the case, they will automatically power on and enter pairing mode.
2. Go to the Bluetooth connection list on your smart phone/tablet/laptop, search for the Bluetooth name on your device, and click to connect.

Power On

Once both earbuds are removed from the case, they will automatically power on. Alternatively, long-press the earbuds for about 3 seconds to manually power on.

Power Off

Once both earbuds are put in the case, they will automatically power off.

Music Play/Pause

Short-press the button to play or pause music.

Music Next/Previous

Double-press the main button of the left earbud to go to the previous song. Double-press the main button of the right earbud to go to the next song.

Answer Call

During an incoming call, press the main button of the earbuds to answer the call.

End Call

During a call, press the main button of the earbuds to end the call.

Reject Call

During an incoming call, press the main button of the earbuds to reject the call.

Cancel Call

During the dialing state, press the main button of the earbuds to cancel a call.

Siri/Google Assistant

Under standby status or music pause status, press the main button of either the right or left earbud for 1.5 seconds to activate voice assistance.

Low Battery Alarm

When the earbuds power is less than 20%, the red light will flash every 5 seconds, and a prompt will be sounded every 60 seconds to charge.

Low Battery Shutdown

When the earbuds run out of battery power, they will automatically shut off.

Automatic Connection

After the initial set-up and connection, the earbuds will automatically connect to your device the next time you turn them on. (Please ensure Bluetooth is active on your device for automatic connection.)

Restore Original Settings

If the two earbuds are not in connection state, power on the earbuds. With red and blue lights flashing, click both buttons for 5 times continuously. The earphones will enter restore setting and turn off after finishing. If the 2 earbuds are in connection, click the flashing light earphone button for 5 times continuously to restore the original setting for both earbuds.

Charging for Earbuds

Put the right and left earbuds into the Charging Cases and close the lid to start the charging process. The charging earbuds will show red lights until fully charged. Once fully charged, the red light will turn off. At the same time, the charging case will show a blue light when the earbuds are charging, and the blue light will be off once the earbuds are fully charged.

Charging for charging case

When the type-C interface is used to charge the charging chamber, the red light will flash, and the red light will be constant when it is full.

(Note: The normal Charging Case holds 320 mAh of battery power, which can charge the earbuds up to 4 times from no battery power before the case needs to be charged.)

True Wireless Earbuds Specifications

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.