components.LT
User Guide for DMP models including: V-6022WC, V-6022WC Wireless Cube Camera, Wireless Cube Camera, Cube Camera, Camera
V-6022WC Installation and Programming Guide | Digital Monitoring Products ... The V-6022WC is a 2 Megapixel indoor video camera that allows users to view ...
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, ...
File Info : application/pdf, 8 Pages, 1.31MB
DocumentDocumentINSTALLATION AND SETUP GUIDE V-6022WC Wireless Cube Camera GET STARTED The V-6022WC is a 2 Megapixel indoor video camera that allows users to view live and recorded HD video clips in Virtual KeypadTM. To activate the camera, you need an active Dealer Admin account at dealer.securecomwireless.com. Compatibility Any active Virtual Keypad account with Cameras & NVRs enabled What's Included One V-6022WC Camera with Mounting Plate 5 VDC Power Supply Mounting Template Hardware Pack One 32 GB SD Card Procedure This guide walks you through the required steps needed to install a V-6022WC camera. They are: 1. Wire the camera. 2. Connect the camera to Wi-Fi. 3. Mount the camera. 4. Configure motion detection regions. V-6022WC Installation and Programming Guide | Digital Monitoring Products 1 WIRE THE CAMERA Refer to Figure 1 for the location of the power and Ethernet connectors. Standard Power Connection To use this camera with a Wi-Fi connection, connect a 5 VDC power source to the camera power connector. You can optionally connect a network cable to the camera Ethernet connector. For compatible power supplies, refer to "Accessories". Note: The V-6022WC does not support POE. Ethernet Reset 5 VDC Power Figure 1:Camera Power Details V-6022WC Installation and Programming Guide | Digital Monitoring Products 2 CONNECT THE CAMERA TO WI-FI Ensure that you know the Wi-Fi network and password that you wish to connect the camera to. 1. Log into Tech APP and select Video. 2. Tap the Add icon in the Cameras section. 3. When prompted to select a connection type, tap Wi-Fi. 4. Enter the Wi-Fi SSID and passphrase. Press Next. 5. The camera will flash a blue LED when it is ready to connect to the Wi-Fi network. Hold the QR code 6-12 inches in front of the camera lens until the red LED flashes faster. The QR code must be facing the camera lens. The LED will turn solid blue once it has been connected to the Wi-Fi network. Press Next. 6. Enter the camera MAC Address. Press Next. 7. Wait for the camera to be added to the system in Tech APP. This may take several minutes. Figure 2:Connect the Camera to Wi-Fi with Tech APP 8. Enter a name for the camera. 9. Under Advanced, you can configure the following basic settings: Video Quality Flip Image Record on Alarm Time Zone Observe DST 10. Press Save. Note: If the LED flashes red (around once every second), it means that the network connection has failed. Press and hold the reset button for 10 seconds until the camera restarts, then try again. STATUS Camera is starting up Ready for Wi-Fi connection Wi-Fi connection successful Wi-Fi connection failed Press and hold the reset button Steady red INDICATOR Flashing blue (around once every second) Steady blue Flashing red (around once every second) Flashing red (around once every second) V-6022WC Installation and Programming Guide | Digital Monitoring Products 3 MOUNT THE CAMERA The V-6022WC is suitable for stand, wall, and ceiling mounting applications. Refer to Figure 3 during mounting and camera adjustment. Wall or Ceiling Mount Ceiling mounting will be covered as an example in this section. However, the same steps may be referenced for wall mounting. 1. Place the mounting template at the location you want to mount the camera. 2. Drill holes into the mounting template. 3. Install the magnetic mounting plate with the supplied mounting screws. 4. Hold the magnetic camera base to the magnetic mounting plate. The camera base will magnetically attach to the mounting plate. Note: The mounting surface must be capable of holding five times the camera's weight. Adjust the Camera 1. Adjust the tilt angle by gently pushing the camera lens forwards and backwards. The camera lens will tilt on the neck of the attached base. 2. Adjust the pan angle by turning the entire camera unit to your desired position on the magnetic mounting plate. Magnetic Mounting Plate Mounting Hole Mounting Hole Magnetic Camera Base Tilt 0° - 90° Pan 0° - 360° Figure 3:Mounting and Adjusting the Camera V-6022WC Installation and Programming Guide | Digital Monitoring Products 4 CONFIGURE MOTION DETECTION REGIONS After mounting the camera, configure the camera motion detection regions in Dealer Admin. 1. Navigate to Dealer Admin and select the camera you want to add a motion detection region to. admin@gmail.com Figure 4:Select a V-6000 Camera in Dealer Admin 2. In the Regions & Analytics section, select +Region and give it a Name. 3. Select the sensitivity of the region. Default is 50. 4. Dealer Admin will populate a 4-point rectangle in camera view screen. Click and drag an endpoint to change the size of the region. admin@gmail.com Figure 5:Configure a Motion Detection Region in Dealer Admin V-6022WC Installation and Programming Guide | Digital Monitoring Products 5 ADDITIONAL INFORMATION Video Privacy in Dealer Admin and Virtual Keypad In Virtual Keypad, end users can choose to allow video access to technicians and dealers. When video access is enabled, all Administrator level app users will receive a notification email. To enable video access, follow the steps below. 1. Navigate to Virtual Keypad. 2. Go to Settings and select Video Privacy. 3. Use the toggle to grant technicians and dealers unlimited access to the video feed. Use the Grant Access button to give temporary access. The default is 12 hours, although access can be revoked instantly by pressing the Revoke Access button. Note: All cameras brought online will immediately be granted access to the video feed for 12 hours. Replace the SD Card Refer to Figure 6 for the location of the SD card slot. 1. Locate the replacement SD card and place it to the side. 2. Insert the SD card into the slot to the left of the camera lens. SD Card Slot Figure 6:Camera Details ORDERING INFORMATION V-6022WC Accessories V-SD32G V-SD64G 2 MP Wireless Cube Camera 32 GB Replacement SD Card 64 GB Replacement SD Card V-6022WC Installation and Programming Guide | Digital Monitoring Products 6 SPECIFICATIONS Sensor and Lens Image Sensor Network Wireless Hardware Power Consumption 5 VDC Weight Dimensions Housing Material Environmental Operating Temperature Operating Humidity 2 MP, 1/2.9" CMOS IEEE 802.11b/g/n Max 4.0 W 0.31 lbs (0.14 kg) 3.0" x 1.7" x 4.9" (7.7 cm x 4.2 cm x 12.5 cm) Plastic -14°F to 104°F (-10°C to 40°C) 95% RH or less, non-condensing CERTIFICATIONS FCC Part 15 Registration ID: CCK-V6022WC Industry Canada: 5251A-V6022WC FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Industry Canada Information This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 18205 Designed, engineered, and manufactured in Springfield, MO using U.S. and global components. LT-2735 23224 © 2023 INTRUSION · FIRE · ACCESS · NETWORKS 2500 North Partnership Boulevard Springfield, Missouri 65803-8877 800.641.4282 | DMP.com