Harley Benton Spaceship PowerBar 60

Safety Instructions

Intended Use

This product is designed as a multiple power supply for effect pedals. Any other use or use under different operating conditions is considered improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.

Danger for Children

Ensure that plastic bags, packaging, etc., are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children use electrical devices unattended.

Electric Shock Caused by High Voltages Inside

Within the device, there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors, or optical components are missing or damaged.

Electric Shock Caused by Short-Circuit

Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.

Possible Staining

The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if necessary, i.e., felt-pad floor protectors or similar.

Where to Use the Product

Never use the product:

• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet

General Handling

To prevent damage, never use force when handling the product. Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners, or flammable cleaning agents.

Features

• Special power adapter to connect and integrate with existing Harley Benton Spaceship 60 pedalboards
• Universal input voltage operation 100 - 240 V
• 11 insulated, filtered, and short-circuit proof outputs eliminate noise and hum
• 4 uninsulated outputs for multi-effect devices or for charging smartphones or tablets
• High current output for modern digital effects
• LED indicator on each output

Scope of Delivery

• 4 x DC cable with a length of 30 cm
• 5 x DC cable with a length of 60 cm
• 4 x DC cable with a length of 90 cm
• 1 x reverse polarity cable with red plug
• 1 x battery clip
• 1 x connector cable with a length of 45 cm with 5.5 x 2.5 mm green coaxial plug to 5.5 x 2.1 mm coaxial plug
• 1 x connector cable with a length of 45 cm with 3.5 mm jack plug to 5.5 x 2.1 mm coaxial plug
• 1 x voltage boost cable, 20 cm
• 1 x current boost cable, 60 cm
• 1 x EIAJ-05 cable
• 1 x power cord with EU plug, 120 cm
• 1 x cable fastening set
• 1 x velcro tape, self-adhesive, 100 mm x 45 mm
• 1 x Allen key
• 2 x aluminium edges for mounting both the powerbar and crossbars from existing Harley Benton Spaceship 60 boards

Operating Elements

The Harley Benton Spaceship PowerBar 60 features several operating elements:

• 1 USB-A output, uninsulated
• 2 USB-C output, uninsulated
• 3 IEC chassis connector C14 for connecting the supplied power cord
• 4 Output 1 with 24 V === @ 2000 mA, uninsulated
• 5 Output 2 with 9 V === @ 3000 mA, uninsulated
• Outputs 3-6 with each 9V === @ 250 mA, insulated
• Outputs 7-9 with each 9V === @ 500 mA, insulated
• Outputs 10-13 with voltage switches, insulated, switchable between 9V @ 500 mA / 12V @ 375 mA / 18V @ 250 mA
• 9 Control LED for outputs 1-13, lights up green when voltage is present, turns off when output is deactivated due to overload.

Diagram Description: A visual representation of the operating elements of the Harley Benton Spaceship PowerBar 60, showing numbered outputs and connections including USB ports, IEC input, and various DC outputs with their specifications. An LED indicator is also shown.

Using the Product

1. Connect the device to the mains using the supplied power cord to put the device into operation.
2. Use a suitable voltage supply cable to connect effect pedals or similar devices which require 24 V === supply voltage at a maximum of 2000 mA to output 1.
3. Use a suitable voltage supply cable to connect devices with high power consumption (i.e., multi-effect devices) which require 9 V === supply voltage at a maximum of 3000 mA to output 2.
4. Use suitable voltage supply cables to connect effect pedals or similar devices which require 9 V === supply voltage at a maximum of 250 mA to outputs 3 - 6.
5. Use suitable voltage supply cables to connect effect pedals or similar devices which require 9 V === supply voltage at a maximum of 500 mA to outputs 7 - 9.
6. Danger of property damage by polarity reversal: Make sure that the polarity of the devices to be connected must be the same as the polarity of the power supply outputs (+). To power a device with polarity-reversed voltage may damage it!
7. Use suitable voltage supply cables to connect effect pedals or similar devices which require 9V, 12V, or 18 V supply voltage at a maximum of 500 mA, 375 mA, or 250 mA to outputs 10 - 13. Set the associated switch above the output to the position of the required voltage. The maximum output power of 45 W must not be exceeded.
8. Danger of property damage by overvoltage: Make sure that connected devices are actually suitable for the set voltage. To power a device with overvoltage may damage it!
9. Use suitable voltage supply cables to connect devices like smartphones or tablets to the USB outputs.
10. Each operational output 1 - 13 is indicated by a green LED. If an output is switched off due to overload, the LED turns off. Then disconnect the pedal in question from the device. After approximately 2 seconds, the normal voltage supply is restored here.
11. To switch off the device, disconnect the power cord from the mains.

Technical Specifications

Connections:

• Output 1: 24 V === @ max. 2000 mA
• Output 2: 9 V === @ max. 3000 mA
• Outputs 3 - 6: 9V === @ max. 250 mA (individually insulated)
• Outputs 7 - 9: 9 V === @ max. 500 mA (individually insulated)
• Outputs 10 - 13: switchable 9/12/18V @ max. 500/375/250 mA (individually insulated)
• USB output: USB-C max. 18 W, USB-A max. 18 W

General Specifications:

• Power output: 45 W
• Current output: 3750 mA
• Supply voltage: 100-240 V~ 50/60 Hz
• Dimensions (W x H x D): 600 mm x 30 mm x 50 mm
• Weight: 0.76 kg
• Ambient conditions: Temperature range 0 °C...40 °C, Relative humidity 20%...80% (non-condensing)