Weber Genesis E-315 / E-415 LP Assembly Guide

Before You Begin

Enhance your assembly experience by downloading the free BILT™ app for 3D step-by-step instructions.

General Assembly Tips:

• Cut all four corners of the carton and fold the sides down.
• Assemble the grill on a flat, level, and soft surface.
• Remove protective film from stainless steel parts before installation.
• Do not use power tools for assembly.
• Assembly requires two people. ?
• Note that there may be visual differences between the illustrations and the actual model purchased.
• Always keep the lid closed when assembling or moving your grill.

Tools

Tools Included: [Visual description: An open-ended wrench is depicted.]

Tools Required: [Visual description: A screwdriver is depicted.]

Parts Overview

The packaging contains various components and hardware bags labeled A through E, as well as main grill parts.

• Hardware Bags (A-E): Contain specific screws, bolts, washers, clips, and a battery for assembly. Refer to individual steps for which bag and part numbers to use.
• Main Components: Includes grates, side panels, and other structural parts that will be assembled into the grill.

Assembly Steps

Step 1: Attach part J (manuals/instructions) to the main frame using one screw (-1) from Bag A. [Diagram shows a hand inserting a screw into a bracket attached to a frame.]

Step 2: Attach part F (side panel) to the frame using one screw (-1) from Bag A. Ensure correct orientation. [Diagram shows a side panel being attached to a frame, with close-ups indicating correct screw placement and a checkmark ✅ for proper alignment.]

Step 3: Assemble the side panels. Attach the side panels to the main frame using screws. [Diagram shows the main frame and side panels being joined with screws.]

Step 4: Attach a shelf or component to the lower part of the frame. [Diagram shows a shelf being slid into place and secured.]

Step 5: Secure the lower part of the frame using two screws (-2) from Bag A. [Diagram shows screws being inserted into the base of the assembled frame.]

Step 6: Attach part F (side panel) to the frame using four screws (-4) from Bag A. Ensure correct orientation. [Diagram shows a panel being attached to the frame with screws, with close-ups indicating correct alignment and a checkmark ✅ for proper fit.]

Step 7: Attach part G (side panel) to the frame using four screws (-4) from Bag A. Ensure correct orientation. [Diagram shows another panel being attached to the frame with screws, with close-ups indicating correct alignment and a checkmark ✅ for proper fit.]

Step 8 (315 Models Only): Attach a component to the frame using one screw (-1) and one fastener (-1) from Bag A. [Diagram shows a hand attaching a component with screws and fasteners to the frame.]

Step 9 (415 Models Only): Attach components to the frame using two screws (-2) from Bag A. [Diagram shows screws being inserted into the frame for specific model 415 components.]

Step 10: Attach the base or legs to the assembled frame using four screws (-4) from Bag A. [Diagram shows the frame being turned and legs/base being attached with screws.]

Step 11: Attach components using two screws (-2) from Bag A. [Diagram shows screws being inserted into the top section of the frame.]

Step 12: Attach wheels to the base. Ensure wheels are locked. [Diagram shows wheels being attached to the base of the grill. Two icons show wheels being locked with a lock symbol ?.]

Step 13: Attach components using two screws (-2) and two fasteners (-2) from Bag B. [Diagram shows parts being attached to the side of the grill with screws and fasteners.]

Step 14: Attach a component using two screws (-2) from Bag B and a clip from Bag C. [Diagram shows a clip and screws being used to attach a part.]

Step 15: Connect gas lines or internal components using two fasteners (-2) and two fasteners (-2) from Bag C. [Diagram shows internal wiring or gas line connections being secured.]

Step 16: Attach components using two screws (-2) from Bag C. [Diagram shows screws attaching a panel or component to the grill body.]

Step 17: Attach a component using two screws (-2) from Bag C. [Diagram shows screws attaching a panel or component to the grill body.]

Step 18: Connect gas lines using one fastener (-1) from Bag C. [Diagram shows a gas connection being made.]

Step 19: Insert battery (AA, -1) into the ignition module from Bag C. [Diagram shows a battery being inserted into a module.]

Step 20: Connect wiring harnesses. [Diagram shows electrical connections being made.]

Step 21: Attach a component using one fastener (-1) from Bag D. [Diagram shows a component being attached with a fastener.]

Step 22: Attach a shelf or component using two screws (-2) from Bag D. Ensure correct orientation. [Diagram shows a shelf being attached, with close-ups indicating correct screw placement and a checkmark ✅ for proper fit.]

Step 23: Attach a shelf or component using two screws (-2) from Bag D. [Diagram shows another shelf or component being attached.]

Step 24: Attach a shelf or component using two screws (-2) from Bag D. Ensure correct orientation. [Diagram shows a shelf being attached, with close-ups indicating correct screw placement and a checkmark ✅ for proper fit.]

Step 25: Attach a shelf or component using two screws (-2) from Bag D. [Diagram shows another shelf or component being attached.]

Step 26: Attach a component, possibly a heat shield or bracket, with associated wiring. [Diagram shows a component with wiring being attached to the grill.]

Step 27: Attach a panel or component using two fasteners (-2) from Bag E. [Diagram shows screws attaching a panel to the grill body.]

Step 28: Connect electrical components. [Diagram shows electrical connections being made to a module.]

Step 29: Secure wiring with a clip. [Diagram shows a clip being used to secure wiring.]

Step 30: Attach components using two fasteners (-2) from Bag E. [Diagram shows fasteners being used to attach parts to the grill.]

Step 31: Attach components using two fasteners (-2) from Bag E. [Diagram shows fasteners being used to attach parts to the grill, possibly doors or side panels.]

Step 32: Attach an extra fastener or component using one fastener (-1) from Bag E. [Diagram shows a final component or fastener being attached.]

Final Checks:

• Ensure all parts are assembled and all hardware is tightened before operating the grill.
• Remove all packing material before operating the grill.
• Always keep the lid closed when assembling or moving your grill.

Registration and Support

Register Today. Register your grill to receive exclusive WEBER content.

Contact Information:

• U.S./EE. UU./États-Unis: 1-800-446-1071
• Mexico/México/Mexique: 01 800 0093237
• Canada/Canadá/Canada: 1-800-446-1071

Details regarding Apple and Google app store trademarks are provided.

© 2023 Designed and engineered by Weber-Stephen Products LLC, 1415 S. Roselle Road, Palatine, Illinois 60067 USA. www.weber.com