Xiaomi United States | Xiaomi Official WebsiteSupport - User Guide | Xiaomi Global服務條款及細則 - 香港官網404 - Xiaomi GlobalEurope DECLARATION OF CONFORMITY - Xiaomi GlobalUK DECLARATION OF CONFORMITY - Xiaomi UK
User Manual for xiaomi models including: BHR5960EU Smart Blender, BHR5960EU, Smart Blender, Blender
User Guide - Xiaomi UK
File Info : application/pdf, 30 Pages, 4.87MB
DocumentDocumentSmart Blender User Manual · 01 Xiaomi · 11 Xiaomi · 19
Read this manual carefully before use, and retain it for future reference.
Precautions
Usage restrictions The blender is for household use only. This appliance can be used by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. The blender's normal operating altitude range is 02000 meters. Do not place the blender on unstable or wet surfaces. Keep it preferably at least 30 cm away from fire or heat sources (such as stoves). Do not place the blender near devices that are susceptible to electromagnetic interference. Do not let people who lack the physical, sensory, or intellectual ability or lack the experience or common sense to use the blender without supervision or guidance. If the blender is not used in accordance with the instructions in the user manual, there may be a risk of injury.
01
Do not allow children to play with the blender. The blender should be placed out of the reach of children. Children should not use it without supervision. Do not hang the power cord on sharp objects. Do not use the blender to heat viscous liquids, including milk, soy milk, cold rice porridge, etc. Otherwise it will lead to build-up on the bo om, which could cause burning and strange smells. Do not use any non-genuine accessories with this blender to avoid potential injuries.
Cleaning & maintenance
Do not immerse the blender in water or splash it with water. Do not use steel wool or other hard objects to clean the heating plate. Use only so cloths for cleaning. If the blender will not be used for an extended period of time, unplug the power cord and take appropriate measures to protect the blender from moisture, dust, and household pests. Ensure that the power cord is disconnected and wait for the jar to cool down before cleaning. The table surface the blender is placed on must be regularly cleaned of grease. Please rinse the jar's interior and accessories with clean water before wiping them dry. The blades are sharp, so please be careful when cleaning or emptying the jar to avoid injury.
02
Precautions for using power supply
Do not use any power supply other than 220240 V AC to avoid fire and electrical shocks. Always unplug the blender by holding the power plug to avoid fire or electrical shocks. Do not plug or unplug the power cord when your hands are wet to avoid injury and electrical shocks. Use only power sockets with a rated current of 10 A at minimum. If the power cord is damaged or broken, it must be replaced by the manufacturer or the a er-sale service team to avoid safety hazards. Do not use other power cord extenders or parts not approved by Xiaomi when repairing. To avoid the risk of fire, do not use the low-quality power strip with this product. Only use the blender on the base provided. Always unplug the blender before cleaning, assembling or disassembling, or a er using. Make sure that the blender is powered off before moving the base.
While in use
Do not add water past the maximum level, or else the water will overflow or spray out and cause burns or other accidents. Idling or overloading is strictly prohibited. Do not move the blender or touch any running parts when in use to avoid accidents. Do not heat without any food or water inside.
03
Do not move the lid and lid plug when in use. Do not allow any liquid to get on the pin connector. There will be residual heat a er heating element works. The surface of the jar and lid will be hot while heating up, so please do not touch them while in use.
About the environment
Steam and heat may damage, discolor or deform your walls and furniture, so keep the product preferably at least 30 cm away from any walls and furniture. When using the blender in a kitchen cabinet, etc., please ensure that the place is well ventilated.
Product Overview
Lid Plug Lid
Hot Drink Scale Mark Blades
Jar Cold Drink Scale Mark
Heating Plate
Rubber Pad
Control Panel Base 04
Indicator Schedule Bu on
Knob/Display
Accessories
Jam 30 min
Cancel Bu on
Tamper
Brush
Measuring Cup
Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.
How to Use
First use 1. When the startup animation ends a er the blender is powered on for the first time, the blender will
enter the language selection screen. Press the knob for the screen to display languages, turn the knob to select a language, and press it to confirm the selection.
2. A er the language is set, turn the knob to enter the Wi-Fi se ings screen. Press the knob to enable/disable Wi-Fi. If no action is performed within 30 seconds, the system will automatically select "No" as default (disable Wi-Fi connection).
Note: The blender will only enter the language selection and Wi-Fi se ings screen the first time it's powered on. If you need to reset later, please go to the se ings menu.
Turning On/off
1. Turning on Every time the blender is plugged in, it will enter pre-start state a er the startup animation ends, and the screen will display "Press and hold to turn on", so press and hold the knob to turn on the blender. The first recipe will appear on the screen when the blender is turned on the first time.
2. Turning off In any other mode than Press & hold to clean mode, press and hold the knob to turn the blender off.
3. Off mode If there is no operation for 10 minutes a er the blender is plugged in, the screen will turn off and the product will enter off mode. Press any bu on to wake it up.
05
Connecting with Mi Home/Xiaomi Home App
This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/Xiaomi Home app to control your device, and to interact with other smart home devices. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search "Mi Home/Xiaomi Home" in the app store to download and install it. Open Mi Home/Xiaomi Home app, tap "+" on the upper right, and then follow prompts to add your device.
* The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default.
Note: The version of the app might have been updated, please follow the instructions based on the current app version.
Wi-Fi Status
Operating Modes Awaiting connection
Connecting Connected
Status Display Wi-Fi icon blinks slowly Wi-Fi icon blinks quickly
Wi-Fi icon remains lit
Note: When the product is on and Wi-Fi is not connected, the Wi-Fi icon will blink. If the blender is not connected to Wi-Fi within 30 minutes, the Wi-Fi icon will turn off.
Operating Instructions
1. Take out the blender and clean the lid plug, lid, and tamper.
2. Wash the ingredients, cut them into 3 cm cubes, and place them in the jar.
3. Install the lid plug onto the lid, and turn the lid clockwise to lock it with the jar. (Figure 1)
4. Place the jar onto the base properly by aligning the small triangle under the handle with the marking on the base. Ensure the base is placed on a stable surface. (Figure 2)
5. Once the blender is powered on, turn the knob to cycle through functions. When the desired function appears on the screen, press the knob to enable it.
(Figure 1) 06
(Figure 2)
Care & Maintenance
Cleaning Watch out for burns from residual heat. Please wait for the jar to cool down before cleaning.
Once the jar has cooled down and is empty, please add clean water and run the Press & hold to clean mode several times to properly clean the jar.
The exterior of the base can be wiped down with a damp cloth once the power is disconnected. Do not soak the base, jar, power cord, and other parts with electronics. Do not directly rinse the base or other parts that contain electronics, such as the bo om of the jar.
Please rinse the jar's interior and accessories with clean water before wiping them dry. The blades are sharp, so please be careful when cleaning to avoid injury.
Do not use abrasive cleaners or corrosive liquids (gasoline, acetone, etc.) to clean the blender.
When parts are stained with fruit or vegetable juice, wiping these parts with several drops of cooking oil before cleaning can help remove stains more easily. Thoroughly dry the parts a er rinsing them with clean water.
If the residue in the jar forms a hard spot that is difficult to remove, please add an appropriate amount of water to soak it before cleaning and wiping the blender dry.
If the inner bo om of the jar is not cleaned up even a er multiple cleanings, and a residual layer has adhered to it, soak it in clean water for a period of time before gently wiping it clean with a cloth dipped in white vinegar. Please mind the blade while wiping to avoid any accidents. (Do not power on the blender when cleaning.)
The blender should be used frequently to keep the motor dry.
If the blender will not be used for an extended period of time, please store it in a well-ventilated and dry place to prevent the motor from ge ing wet and affecting its future use.
Functions
Modes
Operations
Jam Smooth soup Chunky soup Soy milk
Once the blender is powered on, the knob will display "Jam". Press the knob to make
jam, or turn the knob to choose between smooth soup or chunky soup and then
press the knob to begin making the chosen one. Note 1: Task scheduling is available, and the keep warm mode will be enabled by default once cooking
ends. The cooking task will be automatically canceled if you do not resume it a er pausing it for two minutes while in the middle of its operation. Note 2: A er a task starts, press the knob to pause it and press the knob again to resume it. When it is paused, press the cancel bu on to exit the task.
Smoothie Fruit & vegetable juice Milkshake
Turn the knob to select Smoothie, Fruit & vegetable juice, or Milkshake, then press
the knob to start making the chosen drink. Note 1: Task scheduling is not available. The cooking task will be automatically canceled if you do
not resume it a er pausing it for one minute while in the middle of its operation. Note 2: A er a task starts, press the knob to pause it and press the knob again to resume it. When it
is paused, press the cancel bu on to exit the task.
07
Press & hold to clean Manual
Se ings
Turn the knob to the Press & hold to clean mode. Once the ingredients or water is added, press and hold the knob to start the task. Note 1: If the food is not fully blended, enable the Press & hold to clean mode to blend thoroughly in
a short time. Note 2: Select the Press & hold to clean mode for cleaning purposes.
Turn the knob to Manual mode, press and turn it to select the speed. Note: A er a task starts, press the knob to pause it and press the knob again to resume it. When it is paused, press the cancel bu on to exit the task.
1. Language selection: A er the blender is powered on, turn the knob to the se ings screen, and press it for language se ing. Then press the knob to enter the language selection screen, turn the knob to select a language, and press it to confirm the selection. The system will automatically return to the se ings screen a er the setup or if no language is confirmed within 30 seconds.
2. When the blender is connected to a network, turn the knob to select Wi-Fi on the se ings screen. Press the knob to confirm, then you can reset or disconnect the Wi-Fi network.
3. When the blender is not connected to a network, turn the knob to select Wi-Fi on the se ings screen. Press the knob to confirm, then you can connect to Wi-Fi network.
Note: When connecting/disconnecting Wi-Fi network, if there is no operation for 30 seconds, the system will default to the last selected option and return to the se ings screen.
Recipes
Drink Name Time
Ingredients
Jam Smoothie
30 min 45 s
Strawberry 300 g, white sugar 120 g, lemon juice 6 g Ice 300 g (2 cm cubes)
Fruit & vegetable juice
2 min
Carrot 640 g, drinking water 960 ml
Smooth soup 38 min
1 potato (approx. 220 g), cashew 10 g, white mushroom 50 g, salt 2 g, a pinch of pepper, drinking water 720 ml
Chunky soup 35 min
1 potato (approx. 220 g), cashew 10 g, white mushroom 50 g, salt 2 g, a pinch of pepper, drinking water 720 ml
Milkshake Soy milk
1 min 32 min
1 red dragon fruit (400 g), yogurt 300 ml, 5 ice cubes (2 cm³ in size), a small amount of honey
Soybeans 70 g (about 100 ml mark on the measuring cup), drinking water 1000 ml
Manual
1 min
Take Juice as an example: carrot 890 g, drinking water 710 ml
Cautions · When using the smoothie mode, please use ice cubes that have been frozen below -18°C for more than 24 hours, and use the ice cubes immediately a er taking them out. (Please make sure the jar is dry before adding the ice cubes). · The blender should not blend for more than two minutes continuously in fruit & vegetable juice mode and in manual mode, and should not exceed six minutes in total. · If the base overheats while operating, turn off the blender for about 20 minutes and wait for it to cool down before resumption. · Only jam, soy milk, smooth soup, and chunky soup are available for scheduling in advance. Other recipes do not support this function.
08
Error Codes
Code E01 E02 E05 E10 E11
Message Motor overloaded
Place the jar
Overheated
Temperature sensor error Communication error
Explanation
Solution
Motor overloaded
Clean out the food in the jar a er the power is off, and wait for the blender to cool down before powering it on again.
No jar placed on the base
A er placing the jar on the base, return to the menu screen, and press the cancel bu on to enter standby mode.
High temperature alert from bo om temperature sensor
The blender will return to normal when the temperature drops. Press the cancel bu on to enter standby mode.
Bo om temperature sensor has a short or broken circuit.
Contact the a er-sale service team.
Power board and display panel communication error
Contact the a er-sale service team.
Troubleshooting
Issues Food overflows Ingredients cannot be blended.
Burnt food on the jar's bo om
Ingredients not hot a er cooking Display does not light up.
The display is on but the blender is not working.
Solutions
Add a proper amount of ingredients. Add water to the proper water level. Select the desired function according to the user manual. Contact the a er-sale service team.
Add a proper amount of ingredients. Do not add ingredients that are easily burnt on the jar's bo om, like flour. Add water to the proper water level. Clean before use. Select the desired function according to the user manual. Contact the a er-sale service team.
Select the desired function according to the user manual. Contact the a er-sale service team.
Check the power cord and make sure it is plugged in and connected to the power supply. Contact the a er-sale service team.
Re-select the function and press the knob to enable it. Add water to the proper water level and restart the blender a er it cools down. Unplug first, then power on and follow the normal operation steps. Contact the a er-sale service team.
09
Operating noise
The blender will make some sounds while it is working, which is normal. Contact the a er-sale service team.
Notes: · Please check whether the power cord is properly connected and the jar and the lid are properly placed. Immediately unplug and stop using it if the blender emits strange noises, smells, smoke, etc. · When the blender still does not work as expected a er the inspection mentioned above, please contact the a er-sale service team.
Specifications
Name: Smart Blender Rated Voltage: 220240 V~ Blending Power: 1000 W Cold Drink Max. Capacity: 1600 ml Transmit Power: 20 dBm Item Dimensions: 188 × 222 × 436 mm
Off Mode: 0.4 W
Model: MPBJ001ACM-2A Rated Frequency: 5060 Hz Heating Power: 800950 W Hot Drink Max. Capacity: 1200 ml Transmit Frequency: 2.42.4835 GHz Wireless Connectivity: Wi-Fi IEEE 802.11b/g/n 2.4 GHz
BLE GFSK 1 Mbps
When performing the RE test of EN 301 489-1, the product should be tested in the standby state. When performing tests in the 30 MHz-1 GHz band in EN 55014-1, the disturbance power should be used.
Hereby, Guangdong Chunmi Electronic Technology Co., Ltd. declares that the radio equipment type Smart blender MPBJ001ACM-2A is in compliance with Radio Equipment Regulations 2017. The full text of the UK declaration of conformity is available at the following internet address: h ps://www.mi.com/uk/service/support/declaration.html
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
Hereby, Guangdong Chunmi Electronic Technology Co., Ltd. declares that the radio equipment type Smart blender MPBJ001ACM-2A is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: h ps://www.mi.com/global/service/support/declaration. html. For detailed e-manual, please go to www.mi.com/global/support/user-guide.
PSTI
a. Hereby, Guangdong Chunmi Electronic Technology Co., Ltd. declares that the type Smart blender MPBJ001ACM-2A The products comply with UK PSTI regulations (the relevant DoC can be found at the h ps://www.mi.com/global/service/support/declaration.html). b. The support end date December 1, 2024.
Manufactured for: Xiaomi Communications Co., Ltd. Manufactured by: Guangdong Chunmi Electronic Technology Co., Ltd. Address: 2/F, Building C, South No.1 Huanzheng East Road, Beiao Community, Beiao Town, Shunde District, 528311 Foshan City, Guangdong Province, PEOPLE'S REPUBLIC OF CHINA For further information, please go to www.mi.com User Manual Version: V3.3
10
0 ~ 2000 30
220-240 V 10 A
11
30
/
30
12
:
1.
2. Wi-Fi Wi-Fi / Wi-Fi 30 noWi-Fi
Wi-Fi
1.
2. /
3. 10
APP
APP APPAPP Google PlayApple App Store APPAPP +APP
APP APP
13
Wi-Fi
Wi-Fi Wi-Fi Wi-Fi
Wi-Fi Wi-Fi 30 Wi-FiWi-Fi
1.
2. 3
3. (1)
4. (2)
5.
(1)
(2)
/
14
/
1 2 2
1 1 2
/
1/ 2/
1. 30
15
2. Wi-Fi Wi-Fi Wi-Fi
3. Wi-Fi Wi-Fi
Wi-Fi / 30
30 45 2
38
35
1
32 1
300 g 120 g 6 g
300 g2
640 g 960 mL
220 g 10 g 50 g 2 g 720 mL
220 g 10 g 50 g 2 g 720 mL 400 g 300 mL 5 2 70 g 100 mL 1000 mL 890 g 710 mL
-1824 2 6 20
E01
E02
16
E05 E10 E11
/
: 17
MPBJ001ACM-2A
220-240V~
50-60Hz
1000W
800-950W
1600mL
1200mL
20 dBm
2.4-2.4835 GHz
188 × 222 × 436mm
0.4 W
Wi-Fi IEEE 802.11b/g/n 2.4 GHz BLE GFSK 1Mbps
EN 301 489-1RE EN 55014-130MHz-1GHz
1C 528311 852-30773620 www.mi.com/hk/service : V3.3
18
.
. · ·
. . 2000-0 · 30 . · .( )
· .
·
. ·
.
19
. · . . . ·
·
. ·
.
. · . · . · ·
. . · . · . ·
.
20
240-220 ·
. ·
. ·
. . 10 ·
· .
· . Xiaomi
· .
. · ·
. . ·
·
. . · ·
. . ·
21
. · . · . · ·
.
· 30
. ·
.
22
/
30
. : .
. .1
.
.Wi-Fi / .Wi-Fi .2 .(Wi-Fi ) "" 30
. . Wi-Fi
/
.1
. " " .
.2 .
.3 . 10
.
23
Mi Home/Xiaomi Home
*Mi Home/Xiaomi Home . Mi Home/Xiaomi Home
. QR "Mi Home/Xiaomi Home" .
"+" Mi Home/Xiaomi Home . .
. .( ) Xiaomi Home * . :
Wi-Fi
Wi-Fi Wi-Fi Wi-Fi
30 Wi-Fi .Wi-Fi Wi-Fi : .Wi-Fi
. .1 . 3 .2 (1 ) . .3 . .4
(2 ) . . . .5
(2 ) 24
(1 )
. . · . · . · .
. . ·
. . ( ) . · ·
. . ·
. ·
) . . (.
. · ·
.
."" .
. :1 .
. :2 .
25
.
. :1 .
. :2 .
. .
. :1 . :2
. . :
.
. : .1 . 30 . . Wi-Fi .2 . Wi-Fi . Wi-Fi .3 .Wi-Fi 30 Wi-Fi / : .
:
6 120 300
30
( 2 ) 300
45
960 640
2
2 50 10 ( 220 ) 1 720
38
2 50 10 ( 220 ) 1 720
(3 2 ) 5 300 ( 400)
1000 ( 100 ) 70
35
1 32
710 890 :
1
: . 24 18- ·
.( ) . ·
. 20 · . . : ·
26
.
.
. .
.
.
.
E01
E02
E05
E10
E11
. . .
.
.
. .
. .
. .
. .
. .
.
.
.
. .
.
.
27
. .
: . ·
. . ·
MPBJ001ACM-2A : 6050 :
950800 : 1200 :
2.42.4835 : Wi-Fi IEEE 802.11b/g/n 2.4 GHz :
GFSK 1
: ~ 240220 :
1000 : 1600 :
20 : 436 × 222 × 188 :
0.4 :
. EN 301 489-1 · . EN 55014-1 1 30 ·
28
Xiaomi Communications Co., Ltd.: Guangdong Chunmi Electronic Technology Co., Ltd. : ,F/2, Building C, South No.1 Huanzheng East Road, Beijiao Community, Beijiao Town : Shunde District, 528311 Foshan City, Guangdong Province, PEOPLE'S REPUBLIC OF CHINA
www.mi.com 3.3 :
EU REP. Xiaomi Technology Netherlands B.V. Prinses Beatrixlaan 582, 2595BM, The Hague, The Netherlands contact@support.mi.com UK REP. Xiaomi Technology UK Limited Davidson House, Forbury Square, Reading, Berkshire RG1 3EU contact@support.mi.com