Automotive, IoT & Industrial Solutions | NXP SemiconductorsProducts | NXP SemiconductorsBridge demo board | NXP SemiconductorsOur Terms And Conditions Of Commercial Sale | NXP Semiconductors
User Manual for NXP Semiconductors models including: SC16IS750 760 Demo Board, SC16IS750, 760 Demo Board, Demo Board, Board
2024-02-06 — Working with the OM6270 (SC16IS750/760 demo board) requires the kit contents, additional hardware, and a. Windows PC workstation with installed software. 3.1 ...
File Info : application/pdf, 14 Pages, 2.18MB
DocumentDocumentUM11988 SC16IS750/760 demo board Rev. 2.0 -- 6 February 2024 User manual Document information Information Content Keywords SC16IS750, SC16IS760, OM6270, SC16IS750/760 SPI/I2C to UART bridge demo board Abstract The SC16IS750/760 is a slave I2C-bus/SPI interface to a single-channel high performance UART. This user manual describes the setup, configuration and operation of the OM6270 (SC16IS750/760 SPI/I2C to UART bridge demo board) NXP Semiconductors UM11988 SC16IS750/760 demo board IMPORTANT NOTICE For engineering development or evaluation purposes only NXP provides the product under the following conditions: This evaluation kit is for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed-circuit board to make it easier to access inputs, outputs and supply terminals. This evaluation board may be used with any development system or other source of I/O signals by connecting it to the host MCU computer board via off-theshelf cables. This evaluation board is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application heavily depends on proper printed-circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The product provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end device incorporating the product. Due to the open construction of the product, it is the responsibility of the user to take all appropriate precautions for electric discharge. In order to minimize risks associated with the customers' applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact NXP sales and technical support services. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 2 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board 1 Introduction The SC16IS750/760 is a slave I2C-bus/SPI interface to a single-channel high performance UART. It offers data rates up to 5 Mbit/s and guarantees low operating and sleeping current. The SC16IS750 and SC16IS760 also provide the application with 8 additional programmable I/O pins. The device comes in very small HVQFN24, TSSOP24 (SC16IS750/760) packages, which makes it ideally suitable for handheld, battery operated applications. This family of products enables seamless protocol conversion from I2C-bus or SPI to and RS-232/ RS-485 and are fully bidirectional. 2 Finding kit resources and information on the NXP web site NXP Semiconductors provides online resources for this evaluation board and its supported device(s) on http:// www.nxp.com. The information page for the OM6270 (SC16IS750/760 demo board) is at https://www.nxp.com/products/ analog-and-mixed-signal/bridges/spi-ic-to-uart-bridge-demo-board-sc16is750:OM6270. 3 Getting ready Working with the OM6270 (SC16IS750/760 demo board) requires the kit contents, additional hardware, and a Windows PC workstation with installed software. 3.1 Kit contents · Assembled and tested evaluation board in an antistatic bag UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 3 / 14 NXP Semiconductors 4 Getting to know the hardware 4.1 Schematic UM11988 SC16IS750/760 demo board Figure 1.Schematic 1 of 2 UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 4 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board Figure 2.Schematic 2 of 2 5 Configuring the hardware The demo board has an on board microcontroller (U7) which is used to control the SC16IS750/760 through the microcontroller I2C bus. This microcontroller is configured at power up to receive the data through the IrDA port (U10), and the received data are sent back out through the uC's UART port (P2). The on-board microcontroller can be removed from its socket; this allows the SC16IS750/760 to be controlled through the SPI header (JP1) or the I2C header (JP6). Please refer to the schematics for more detail of the headers' pin map. When the external controller is selected (U7 is removed), a ribbon cable can be made to connect the external controller's I2C or SPI bus to the demo board. This option allows the user to control the SC16IS750/760 directly with the external controller, and it also allows the user to quickly develop his software without modify his system to add the 16IS750/760 and the necessary components. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 5 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board 5.1 Demo modes The demo modes can be choose by the jumper on JP8 pin 1 and 2 (IO3). If the jumper is missing the datapath is between IrDA port and uC serial port. In this mode if any data received by SC16IS750/760 through the IrDA port will be send out to P2. If the jumper is installed between JP8 pin 1 and 2, the SC16IS750/760 is in software loop back mode. Any data received through P1 will be read by the on-board uC and the uC automatically sends the data back to P1 port. 5.1.1 Demo modes setup instructions 1. IrDA demo a. Get this shareware program - PCRemoteControl from this web site: www.pcremotecontrol.com b. Install the shareware program on your PC c. Run the program. d. Open the file: Philips_Universal.pcr on the disk e. Change the baud rate to 19.2 Kbps and others settings exactly as shown below (Setting Original of control Properties) and click on Accept. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 6 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board f. Click on RUN g. Connect the serial cable between P2 port of the demo board and your PC's serial port. h. Remove jumper on JP8 between pin 1 and 2 (put it on JP8 pin 1 only for later use). i. Make sure there is no jumper on JP18, and the jumper is on JP20. j. Power up the demo board plug in the power jack. k. Open the Microsoft PowerPoint Program. l. Open any presentation file m. Point the remote control at the demo board's IrDA port and press Channel UP or Channel Down key, the Power Point pages will be flipped forward or backward. 2. Serial port demo a. Connect the serial cable between P1 of the demo board and you PC b. Open HyperTerminal program c. Change the Baud Rate to 115.2Kbps if needed d. Put a jumper on JP8 pin 1 and 2 e. Make sure the jumper is on JP18, and there should be no jumper on JP20 f. Power up the demo board plug in the power jack UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 7 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board g. Send any text file (the one on the disk can also be used) and the text will be automatically sent back from the on-board microcontroller. 5.2 SC16IS750/760 address section This device can be configured as any of the following 16 I2C addresses by installing the jumpers: Table 1.Address section JP4 VCC (label pin 1) VCC (label pin 1) VCC (label pin 1) VCC (label pin 1) GND (not label) GND (not label) GND (not label) GND (not label) SCL JP3 VCC (label pin 1) GND (not label) SCL SDA VCC (label pin 1) GND (not label) SCL SDA VCC (label pin 1) SC16IS750/760 I2C ADDRESS 0x90 0x92 0x94 0x96 0x98 0x9A (factory default) 0x9C 0x9E 0xA0 UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 8 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board Table 1.Address section...continued JP4 SCL SCL SCL SDA SDA SDA SDA JP3 GND (not label) SCL SDA VCC (label pin 1) GND (not label) SCL SDA SC16IS750/760 I2C ADDRESS 0xA2 0xA4 0xA6 0xA8 0xAA 0xAC 0xAE 5.3 I2C or SPI configuration The on-board microcontroller is programmed to control the SC16IS750/760 through I2C bus. But if the 16IS750/760 is to be controlled by an external controller through either JP1 or JP6 then the controlled bus is selectable by JP2. I2C bus is selected by installing the jumper on pin 1 and 2 of JP2, and SPI bus is selected by installing the jumper on pin 2 and 3 of JP2. e 5.4 Modem pins or I/O pins Four of the 16IS750/760 I/O pins can also be programmed as normal I/O pins. When these pins are programmed as modem pins, they are routed to the serial port through JP5. This requires the jumper to be on pin 1 and 2 of JP5. When these four pins are programmed as I/O pins, they are routed to JP7 through JP5. This requires the jumper to be on pin 2 and 3 of JP5. In addition, there are 8 LEDs on boards and can be turned on or off by the SC16IS750/760 I/O pins when programmed as outputs. 5.4.1 Modem port, IrDA or RS-485 port On this board the SC16C750/760 receiver pin can be routed from one of these three sources: IrDA Port (U10), Serial Port (P1) or RS-485 Port (JP14). Please see the table below: Table 2.Receiver pin routing JP18 JP20 ON OFF OFF ON OFF OFF JP19 OFF OFF ON Receive from Serial Port Receive from IrDA Port Receive from RS-485 Port The transmitter pin from SC16C750/760 goes to all three ports, and there is no option to isolate them. 5.5 Power supply options The demo board is normally powered from a 5V-7.5V DC adapter which plugs into the power jack J5. This option requires the jumper JP17 to be installed. Additionally a 3.3V external power source can be used to supply power to the demo board. This option requires the jumper on JP17 to be removed and the external 3.3V power is connected to JP17 pin 1. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 9 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board 5.6 SC16IS750/760 hardware reset options SC16C750/760 can be manually reset with the push switch (S1) or through the on-board uC (U7 pin25). The factory default is with the S1 switch, therefore, JP16 jumper is installed on pin 2 and 3. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 10 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board 6 Revision history Table 3.Revision history Document ID UM11988 v.2.0 Release date 6 February 2024 Description · Assigned UM number and updated style of user manual to current format set forth by NXP UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 11 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board Legal information Definitions Draft -- A draft status on a document indicates that the content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included in a draft version of a document and shall have no liability for the consequences of use of such information. Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at https://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Suitability for use in non-automotive qualified products -- Unless this document expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document, including the legal information in that document, is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Security -- Customer understands that all NXP products may be subject to unidentified vulnerabilities or may support established security standards or specifications with known limitations. Customer is responsible for the design and operation of its applications and products throughout their lifecycles to reduce the effect of these vulnerabilities on customer's applications and products. Customer's responsibility also extends to other open and/or proprietary technologies supported by NXP products for use in customer's applications. NXP accepts no liability for any vulnerability. Customer should regularly check security updates from NXP and follow up appropriately. Customer shall select products with security features that best meet rules, regulations, and standards of the intended application and make the ultimate design decisions regarding its products and is solely responsible for compliance with all legal, regulatory, and security related requirements concerning its products, regardless of any information or support that may be provided by NXP. NXP has a Product Security Incident Response Team (PSIRT) (reachable at PSIRT@nxp.com) that manages the investigation, reporting, and solution release to security vulnerabilities of NXP products. NXP B.V. -- NXP B.V. is not an operating company and it does not distribute or sell products. Trademarks Notice: All referenced brands, product names, service names, and trademarks are the property of their respective owners. NXP -- wordmark and logo are trademarks of NXP B.V. UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 12 / 14 NXP Semiconductors UM11988 SC16IS750/760 demo board Tables Tab. 1. Address section .................................................8 Tab. 2. Receiver pin routing .......................................... 9 Tab. 3. Revision history ...............................................11 Figures Fig. 1. Schematic 1 of 2 ...............................................4 Fig. 2. Schematic 2 of 2 ...............................................5 UM11988 User manual All information provided in this document is subject to legal disclaimers. Rev. 2.0 -- 6 February 2024 © 2024 NXP B.V. All rights reserved. 13 / 14 NXP Semiconductors Contents 1 2 3 3.1 4 4.1 5 5.1 5.1.1 5.2 5.3 5.4 5.4.1 5.5 5.6 6 Introduction ...................................................... 3 Finding kit resources and information on the NXP web site ........................................3 Getting ready ................................................... 3 Kit contents ........................................................3 Getting to know the hardware ........................ 4 Schematic .......................................................... 4 Configuring the hardware ............................... 5 Demo modes ..................................................... 6 Demo modes setup instructions ........................ 6 SC16IS750/760 address section ....................... 8 I2C or SPI configuration .................................... 9 Modem pins or I/O pins .....................................9 Modem port, IrDA or RS-485 port ..................... 9 Power supply options ........................................ 9 SC16IS750/760 hardware reset options .......... 10 Revision history .............................................11 Legal information ...........................................12 UM11988 SC16IS750/760 demo board Please be aware that important notices concerning this document and the product(s) described herein, have been included in section 'Legal information'. © 2024 NXP B.V. For more information, please visit: https://www.nxp.com All rights reserved. Date of release: 6 February 2024 Document identifier: UM11988