User Guide for Wistron NeWeb models including: LV65B Indoor Outdoor CPE, LV65B, Indoor Outdoor CPE, Outdoor CPE
Wistron NeWeb Corporation LVPK-65 NKR-LVPK-65 NKRLVPK65 lvpk 65
File Info : application/pdf, 22 Pages, 1.12MB
DocumentDocumentLV65B Indoor/Outdoor CPE User Guide (LV65B) Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF Exposure Statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at at least 21 inches from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. When installed on a wall in an outdoor location, the device must be installed at a height above head level to prevent people from standing directly in front of the device and in the line of sight between the device and the 5G base station. For balcony railing or other installations, the device must be installed at a location that ensures no one is able to pass or stand directly in front of the device, and in the line of sight between the device and the 5G base station. Safety Warnings Adapter Do not use any other power adapter except the one that accompanies this unit or a power adapter identified in the list below. Use of another adapter could result in damage to the unit. The following power adapter is qualified for use with this Tri-band - 5G Business Internet Receiver: This unit must be powered by Delta Electronics, model ADH-65BR H or equivalent UL listed power adapter rated @ output 56Vdc, Maximum 1.161A. Caution Ensure to connect the power cord of the power adapter to a socket outlet with an earthing connection. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Statement Installation of the device must be carried out by professional, trained technicians. This CPE is intended for point-to-point 5G mmWave digital communications applications. The front side of the CPE (the side with the mmWave antenna) should be installed and operated under line-of-sight conditions. Chapter 1 Introduction Unboxing Information/Product Package Inside the product package for the LV65B CPE you should find the following items: Outdoor (Device package): Items Power adapter Quantity 1 IDU Kit (Separate from device package) Items Indoor bracket Screws & anchors (indoor) Window wipe Window wedge Device rear cover Device rear cover/IO cover screw pack IO cover ODU Kit (Separate from device package) Items J-pole (wood screw included) ODU bracket Hose clamp Ground block (surge protector) Cable gland Quantity 1 2 of each 1 2 1 4 of each 1 Quantity 1 1 2 1 1 Product Overview Indoor: Outdoor: Cable gland IO cover J-pole screw (2 pcs) Front side Side view Back side LED Label GND screw Bottom side Outdoor: SIM slot cover (Material: rubber) I/O cap Remove the I/O cap to access the SIM slot cover SIM slot cover (Material: rubber) Remove the SIM slot cover to insert/remove a SIM card or Micro USB card. PSE Adapter: Ethernet Ports on the side of the PSE Adapter J-Pole Installation Step 1: · Adjust pole angle to best meet base station direction. · Tighten 2 elbow nut to fix the angle: Torque: 140 +/-10 kgf-cm Torque: 10.12 +/-0.72 lbf-ft · Detail of the elbow screw is shown in next page. Step 2: 5 mm · Hang the ODU device on the J-Pole · Tightening two HEXI screw after ODE hang in place (screw had pre-mounted with j-pole already) Torque: 60 +/-10 kgf-cm Torque: 4.32 +/-0.72 lbf-ft Step 3: Detail of the elbow screw: M6 nut Tighten the nut to fix the angle Left View Step 4: Top View Right View Unit: mm · Tighten 4 screws to fix the base bracket onto the wall. · Screw information: Screw Type: ¼"x2" Wood Screw Screw Head: HEX head Step 5: · (If need) Loosen 2 nuts and re-adjust pole angle to best meet base station direction. · Tighten 2 elbow nut to fix the angle: Step 6: Torque: 140 +/-10 kgf-cm Torque: 10.12 +/-0.72 lbf-ft Finish the waterproof cable gland setup as below: Note: For ODU installation, please use the RJ45 cable without latch jacket. Step 7: Indoor Installation (Glass Window Mounting) Step 1: Signal scanning Hold the Verizon Receiver close to the window to perform signal scanning (hold the device at a height above your head when doing so). Once a location with good signal strength is found, the LED on the device will turn solid white. Affix a location sticker to the spot on the window glass where the device will be mounted (the location stickers can be found on the side of the device's cover). Step 2: Clean the mounting location with the included alcohol wipes. Wait for the alcohol to dry before proceeding to the next step. Step 3: Peel off the protective film from the Gecko tape on the indoor bracket, and then affix the indoor bracket on the window in the orientation shown below. Protective film Step 4: Use both thumbs to apply solid pressure in all areas where Gecko tape makes contact with the glass to ensure a secure installation. Whenever possible, check the adhesion by looking at the bracket from the outside in. Note: If, after installation, the bracket is not horizontal, you can use the lazy Susan feature to adjust the orientation of the bracket. Step 5: Once the indoor bracket is securely affixed to the window, align the bracket slot on the IDU with the bracket arms on the bracket, then push the device into the bracket until a "click" sound is heard. Step 6: Adjust the orientation of the device until its top and sides are perfectly horizontal or vertical. Refer to the image on the bottom right for the correct orientation. Indoor Installation (Glass Window Mounting) Step 1: Signal scanning Hold the Tri-band - 5G Business Internet Receiver near different locations on the wall to perform signal scanning (hold the device at a height above your head when doing so). Once a location with good signal strength is found, the LED on the device will turn solid white. Affix a location sticker to the spot. Step 2: Mark the screw locations Place the indoor bracket on the location on the wall where you want to install the device, then use a pen to mark the locations where the screws will be drilled into the wall (as indicated in the right image below). Note: DO NOT peel off the protective backing when installing the bracket on a wall. Protective film Step 3: Drill installation holes and install the bracket Use a power screwdriver to drill holes in the marked locations, then take two wall anchors and place them into the holes (make sure the tops of the anchors are flush with the wall). Step 4: Install bracket Align the holes on the indoor bracket with the wall anchors, then take two screws from the indoor wall screw pack and screw them into the wall anchors. Step 5: Install the device onto the bracket After installing the bracket, place the device onto the bracket (refer to step 5 of the indoor glass window mounting process) and conduct cable management as needed. LED and Audio Behavior Receiver LED Definition: Status Boot up Power On / Normal Operating Mode Solid White Bluetooth Pairing BT (Shows for 60 seconds or until the device is paired) Cyan to OFF to Green to OFF (switch every 200 ms) PWR LED BT connection successful Cyan blinking (200 ms ON, 200 ms OFF) × 3 BT connection failure Red blinking (200 ms ON, 200 ms OFF) × 3 Changing modes manually Changing from installation mode to regular mode (press and hold RESET button for at least 3 seconds) Cyan blinking (200 ms ON, 200 ms OFF) × 3 Installation mode enabled Solid Amber Changing from regular mode to installation mode (press and hold RESET button for at least 3 seconds) Amber blinking (200 ms ON, 200 ms OFF) × 3 FW Updated FW updating Green blinking (200 ms ON, 200 ms OFF) × 3 until FW update is completed Status LAN Ethernet port is connected and active Solid White, Link partner advertisement speed is equal or higher than 1 Gbps (ETH0) Ethernet Port Trouble Solid Red, Link partner advertisement speed is less than 1 Gbps (ETH0) Status Regular mode LAN LED DATA LED Sound Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable Sound Not Applicable Not Applicable Sound Internet available Solid White, Internet APN is available Internet not available Solid Red, Internet APN is not available Internet disabled through device settings Amber blinking (600 ms ON, 600 ms OFF) until Internet's available Status Cellular Connectivity mmWave Connectivity Solid White, Blink for Operation/Search Mode. Connectivity LED Sub-6 Connectivity Solid Cyan, Blink for Operation/Search Mode. 4G Connectivity Solid Green, Blink for Operation/Search Mode. No service / No signal Solid Red, Blink for Operation/Search Mode. Error Scenario SIM related error (No SIM card / SIM card error or locked) Solid Amber Status Signal strength Excellent Signal (aka strong) Solid White Good Signal Solid Cyan Adequate signal (aka weak) Solid Green Poor signal Solid Red RSSI LED Not Applicable Not Applicable Not Applicable Sound Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable Sound Not Applicable Not Applicable Not Applicable Not Applicable Power adapter LED Definition: Mode AC Power connected Receiver connected No AC Power connection No Receiver connection Status Power LED will turn white only if the AC power cord is connected to the AC power outlet. PoE LED will turn white only if the Receiver is connected to the port. If there is no connected AC power outlet, these two LED will not light up. If there is no connected Receiver or Ethernet cable is connected to the wrong port, the PoE LED will not light up. Power LED Pattern White -Off -- PoE LED Pattern -- White Off Off Reset Button Button press duration Hold (>3 seconds) Hold (1-2 seconds) Single click (<1 second) Function Switch between installation mode and regular usage mode Restores device to factory settings Resets the device's smart antenna (this needs to be done before any subsequent signal scans after the first one) Chapter 2 Product Specifications Bands Memory Dimensions Weight Connector Type Operating Temperature 5G mmWave: n261 / n260 5G Sub-6: n2, n5, n48, n66, n77 4G: B2, B5, B13, B48, B66 MCP (1 GB LPDDR4 + 1 GB NAND) 9.9 × 5.5 × 2.8 inches (Indoor) 11.3 × 6.8 × 5.0 inches (Outdoor) 2.68 lb (Indoor device only; bracket not included) 8.44 lb (Outdoor device only; bracket not included) RJ45 (5 Gbps) × 1 0 °C to 40 °C (Indoor) -30 °C to 55 °C (Outdoor)GPL Ghostscript 9.27