Instruction Manual for ZigBee models including: SR-ZG2819S-CCT, CCT Remote, SR-ZG2819S-CCT CCT Remote, Remote
09.ZG2819S.04841 Function introduction Important: Read All Instructions Prior to Installation Product Data • This device contains AAA batteries that shall be stored and disposed properly.
White Ambiance Afstandsbediening ZIgbee | ROBB Smarrt | We ❤️ Smart! | ROBBshop
ZigBee CCT Remote Important: Read All Instructions Prior to Installation Function introduction Press and hold down to increase/ decrease light intensity 25% brightness Click to turn ON/OFF all groups 75% brightness S1 S2 S3 Front side 4.5V(3xAAA battery) Bottom side 09.ZG2819S.04841 Indicator: indicate the state of remote control Touch color wheel, touch to select color temperature Product Data Protocol Operation Voltage Transmission Frequency Transmission Range (free field) Protection Type Dimming Range Dimension Protection Grade ZigBee 3.0 4.5V(3xAAA battery) 2.4GHz 30m IP20 0.1%-100% 120x55x17mm IP20 Group numbers: Click to choose the group/groups, press and hold down to turn on/off corresponding group 50% brightness 100% brightness Press and hold down to save colors; Click to recall the saved colors · ZigBee CCT remote based on ZigBee 3.0 · Enables to control CCT lighting devices · High sensitive & high stable touch color wheel, fast & precise color control · Battery powered remote with low power consumption · Enables to pair ZigBee lighting devices via touchlink commissioning · Supports find and bind mode to pair with ZigBee lighting devices · Supports 4 groups for binding max. 30 lighting devices · 2.4 GHz global operation · Transmission range up to 30m · Compatible with universal ZigBee Gateway products · Compatible with universal CCT ZigBee lighting devices ZigBee Clusters Supported by This Remote Are As Follows: Input clusters: · Basic · Power Configuration · Identify · Diagnostics Output clusters: · Identify · Group · Scene · On/off · Level control · Ota Magnetic Bracket · Color control Safety & Warnings · This device contains AAA batteries that shall be stored and disposed properly. · DO NOT expose the device to moisture. Operation 1.This ZigBee CCT remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system. 2.This ZigBee remote supports 4 groups for binding max. 30 lighting devices and enables to control CCT ZigBee lighting devices. 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the remote from previous zigbee network if it has already been added to it, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 4: Immediately short press to search nearby network, indicator flashes every 1 second, 20 seconds timeout if there is no network. Indicator will then blink 5 times quickly for successful pairing. S1 S2 S3 LED indicator Step 2: From your zigbee controller or hub interface, choose to add device or accessory and enter Pairing mode as instructed by the controller. Step 3: Press and hold down until LED indicator turns on. Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface. 2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the remote as instructed, indicator flashes 3 times quickly to indicate successful removing. 6. Factory Reset Manually Step 1: Press and hold down until LED indicator turns on. S1 S2 S3 LED indicator Note: All configuration parameters will be reset after the remote is reset or removed from the network. Step 2: Immediately short press 5 times continuously, indicator flashes 3 times quickly to indicate successful reset. 4. TouchLink to a Zigbee Lighting Device Step 1: Set the zigbee lighting device to start TouchLink commissioning, please refer to its manual to learn how. LED indicator < 10cm ZigBee Lighting Device Step 4: Short press any button to choose a group to touchlink. Step 5: Press and hold down until LED indicator blinks once and stay solid on. S1 S2 S3 Step 2: Bring the remote within 10cm of the lighting device. Step 3: Short press to activate the remote, LED indicator turns on. Step 6:Immediately short press to start TouchLink commissioning of the remote. LED indicator flashes fast for 3S, then flash 6 times slowly to indicate successful pairing to the device and the light connected to the device will blink twice. Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices. 2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices. 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. 4) After TouchLink, the remote can control the linked lighting devices. 7. Remove a Touchlink Paired ZigBee Lighting Device Step 1: Set the Touchlink paired zigbee device to start TouchLink commissioning, please refer to its manual to learn how. LED indicator < 10cm ZigBee Lighting Device Step 4: Short press the group button that the device was linked to. Step 2: Bring the remote within 10cm of the lighting device. Step 5: Press and hold down until LED indicator blinks once and stay solid on. S1 S2 S3 Step 3: Short press to activate the remote, LED indicator turns on. Step 6: Immediately short press twice to start TouchLink removing of the remote. LED indicator flashes fast for 3S, then flash 6 times slowly to indicate 8. Factory Reset a Lighting Device (Touch Reset) successful removing. Note: the device shall be added to a network, the remote added to the same one or not added to any network. Step 1: Set the zigbee device to start TouchLink commissioning, refer to its manual. LED indicator < 10cm ZigBee Lighting Device Step 3: Press and hold down until LED indicator turns on. S1 S2 S3 Step 2: Bring the remote within 10cm of the lighting device. Step 4:Immediately short press 5 times to start Touch Reset of the remote. LED indicator flashes fast for 3S, then flash 3 times slowly to indicate successful reset. 9. Find and Bind a Zigbee Lighting Device Note: Make sure the device and remote already added to the same zigbee network. Step 1: Start find and bind mode on the Zigbee lighting device (initiator node) and enable it to find and bind target, refer to its manual. LED indicator ZigBee Lighting Device Step 3: Short press a group button that you would like to bind the device to. Step 4:Press and hold down until LED indicator blinks once and stay solid on. Note: Each remote can bind max. 30 lighting devices. S1 S2 S3 Step 2: Short press to activate the remote, LED indicator turns on. Step 5:Short press to enable the remote (target node) to find and bind initiator. LED indicator flashes 4 times for successful binding or twice if binding fails. 10. Find and Unbind a Zigbee Lighting Device Step 1: Start find and bind mode on the ZigBee lighting device (initiator node) and enable it to find and unbind target, refer to its manual. Step 3: Short press the group button that the device already bound to. Step 4:Press and hold down until LED indicator blinks once and stay solid on. S1 S2 S3 LED indicator ZigBee Lighting Device Step 2: Short press to activate the remote, LED indicator turns on. Step 5:Short press twice to enable the remote (target node) to find and unbind initiator. LED indicator flashes 4 times for successful unbinding or twice if unbinding fails. 11. Clear All Find and Bind Mode Paired Lighting Devices of a Group LED indicator 12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required) Step 1: Factory reset the remote and the lighting device, refer to their manuals. Step 2: TouchLink the remote and device to setup a network, refer to their manuals. LED indicator < 10cm ZigBee Lighting Device Step 3:Press and hold down until LED indicator turns on. Step 4: Short press button S1 to enable the network to discover and add devices, LED indicator will flash twice. 180 seconds timeout, repeat the operation. S1 S2 S3 Step 5:Set another remote into network pairing mode and pair it to the network, refer to its manual. Step 6: Add more remotes to the network as you would like. Step 7: Factory reset the lighting devices that you would like then add them to the network, refer to their manuals. Step 8: Touchlink to pair the added remotes and lighting devices, refer to their manuals. Each remote can link with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes. 13. OTA The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically. 14. How to Check Whether the Remote Belongs to a Network or not Activate the remote by clicking All On/Off button (indicator on), then short press any other buttons except group buttons, indicator blinking 3 times means the remote does not belong to any network, blinking once or twice means it has already been added to a network. 15. Battery Power Monitor Function The remote will report battery power value to the coordinator under following situations: · When powered on. · When short pressing both S2 and S3 buttons simultaneously. · When operating the switch to send data packets (over 4 hours since last operation). · When added to the network by a coordinator. Step 2: Short press to choose the group that you would like to unbind all devices. Step 3:Press and hold down until LED indicator blinks once and stay solid on. S1 S2 S3 Step 1: Short press to activate the remote, LED indicator turns on. Step 4:Short press 5 times continuously to clear all bound lighting devices with this group. LED indicator flashes 4 times for successful unbinding.Corel PDF Engine Version 14.0.0.653 CorelDRAW