Instruction Manual for SEVERTSON models including: Narrow Fixed Frame Series, Frame Series, Narrow Fixed, ALR UST- HDTV
Staub. SEVERTSON - 7MM NARROW BEZEL SERIES 16:9 100" ULTRA SHORT THROW AMBIENT LIGHT REJECTING
Staub. SEVERTSON - 7MM NARROW BEZEL SERIES 16:9 120" ULTRA SHORT THROW AMBIENT LIGHT REJECTING
File Info : application/pdf, 7 Pages, 4.00MB
DocumentDocumentInstruction Manual for Narrow Fixed Frame Series Part List 2c2 M5*40 4c6 2c3 2c2 16c16 M5*6 16c20 10c12 2c2 2c2 M5*40 2c3 M5*6 2c3 2c3 1c1 4c5 4c5 M5*6 32c36 Micro fiber cloth x1 Plastic sheet x1 2c2 2c2 M5*8 2c3 2c3 Remark: Above spare parts quantity inside () is equipped. IMPORTANT: BEFORE YOU BEGIN To avoid staining or scratching the screen, wash your hands and clean the work area before starting. Do not use knives or sharp objects to open the packing boxes. Care and Cleaning Clean the screen with a microfiber cloth only. DO NOT use soap, water, harsh detergents, chemicals, distilled spirits or petroleum-based chemicals to clean the screen. Doing so may result in severe damage to the screen or the frame covering. Use a household vacuum cleaner with a brush or furniture cleaning attachment to clean the velvet frame material. Avoid using excessive amounts of water on the frame. Installation 1-1.One-hole Nut Slide 6 one-hole nuts into each long frame piece. 1-1 1-2.Springs Refer to spring sticker on each frame piece and slide the correct quantity of springs into each frame piece. Ensure that the hook on the spring points down toward the frame. 1-2 YYQDT 1-3.Four-hole Corner Bracket Slide 1 small (sharp end) and 1 big (round end) corner bracket into each end of the long frame pieces as shown in figure 1-3. (Note that the small corner bracket should be in the same groove as the nut.) 1-3 ç Frame Assembly 2-1 2-2. Secure frame pieces with black round head screws provided. 2-2 èSupport Bar Assembly Place the support bar (if required) onto the middle of the retainer plates as shown in figure 3-1, and secure it with 2 of the provided black round head screws. 3-1 3-2 CAUTION: When handling ambient light rejecting screen material, please keep it flat at all times. To help ensure it stays flat, unroll the screen carefully, and do not fold or crease the material. Always ensure there is nothing resting on or under the material. Always wear gloves when handling the material. é. Screen Materials Attachment 1). Place the plastic sheet (F) flat on a clean flat surface, then carefully unroll the screen materials evenly onto the plastic sheet. The projection surface should be downwards and the back side should be upwards. 2). Place the assembled frame carefully on top of the screen material, centering it on the material. 3)Slide the springs to align with the eyelets in the screen materials ' ê. Secure Screen Materials 1). Fold the edges of the screen material over the edge of the frame. Starting with the opposite corners, then the centers as shown in figure 5-1, 5-2 hook the springs through the material eyelets to secure it in place. Then secure the rest of the eyelets with the springs until all eyelets have been secured as shown in figures 5-2 and 5-3. 5-1 3 5 1 5-3 7 8 2 6 4 Smooth out any wrinkles in the material with gloved hands. 5-4 Install outer frame Slide 3 one-hole nuts into each long outer frame piece, and 2 one-hole nuts into each short outer frame piece; Attach the outer frames on to the frame as shown in figures 6-1 and 6-2. 6-1 5-5 6-2 Install the retaining plate Screw the retaining plates on the one - hole nuts as shown in figure 6-3. 6-3 Install the mounting brackets 1). Secure two mounting brackets with the 1-hole nut in the top frame using round head screws. Do not tighten the screws completely - the brackets should be able to slide left and right 2). Secure the circular metal piece to the lower frame in the same fashion, using the provided flat head screws. Do not tighten the screws completely. 6-1 6-2 Measure the overall Length (A) and Height (B) of the screen frame. 7-1 " # Drill 4 holes in the wall at the desired height. The two holes horizontal distance should be 2/3 A, the vertical distance should be B minus 4 1/8" (105mm). 7-2 " Hammer the expansion bolts into the 4 drilled holes, and drive 2 round head self-tapping screws into the upper expansion bolts, leaving about 1/4" (5mm) extended for hanging the screen on. Install the lower 2 magnet pieces using 2 flat self-tapping screws. Hang the screen on the upper brackets and attach the lower frame to the wall using the magnets. 7-3 7-4 5mm Upper Front Lower