Installation Guide for Fingertec models including: Kadex Plus Access Control Device, Kadex Plus, Access Control Device, Control Device, Device
22 mars 2024 — Avoid strong sunlight. 2. Install the terminal 1.5m from the ground level (measure the height from the ground to the face camera)”.2 pages
File Info : application/pdf, 2 Pages, 441.90KB
DocumentDocumentInstallation Guide TimeTec © 2024, All Rights Reserved · 032024 Step 1 Determine the Installation Location · Avoid installing the terminals in locations that have contact with strong light source (e.g direct sunlight, spotlight, fluorescent light, etc) Step 3 Wiring for Power Supply Use power cables to connect to a linear power supply with specifications of 12VDC 3A to Power Port. Indoor Use Avoid Glass Refraction Avoid Direct Sunlight & Exposure Far Away Heat Source · Avoid installing the terminals in locations with high moisture or condensation levels in the air · The recommended installation height of the terminal from the ground to the camera is 1.5 meter. Step 2 Mount Terminal on a Wall 4 feet / 1.5 meter (recommended) 1. Avoid strong sunlight 2. Install the terminal 1.5m from the ground level (measure the height from the ground to the face camera)" After measuring the height accordingly and make relevant markings on the wall, drill the screws into the wall to secure the back plate. Attach the terminal to the back plate and tighten the screws. Refer to Appendix II for dimensions and measurements of installation. Step 4 Setting Up Data Communications The data communication ports are positioned at the rear of the terminal, please refer to the diagram shown on Step 3 to determine the wiring. Plug the communication jacks (TCP/IP) to the corresponding ports. TCP/IP LAN Connection For TCP/IP connection, connect the other end (normal RJ45 jack) to the local area network hub or a PC. Configure the device ID, IP ad- dress, subnet mask and Gateway or turn on DHCP function in the terminal (refer to the hardware user manual for details). Wi-Fi Settings Menu > COMM. > Wi-Fi Settings > WIFI=ON Select SSID > Insert WIFI password > Connect to Wi-Fi (OK) It will indicate that it is Connected and will receive IP address as per DHCP Server. Device Type Settings Menu > System > Device Type Settings Please choose device type according to your need 1. Ingress Software (Attendance Mode) and TimeTec Attendance Communication Protocol = PUSH Protocol Device Type = T&A PUSH 2. Ingress Software (Access Mode) Communication Protocol = PUSH Protocol Device Type = A&C PUSH 3. TimeTec Access Communication Protocol = Best Protocol Step 5 Finalizing the installation 1. Check that all cable connections are done correctly. 2. Attach the terminal to the corresponding back plate, tight- en the screws to fix the terminal on a wall. 3. Switch on the power to the terminal. 4. Start using it. Other Accessories Note: All Accessories are offered at http://accessory.fingertec.com AdapTec Plus Appendix I Power Supply & Door Lock System Wiring Diagrams Diagram1 · Normally Close (NC) Diagram 2 · Slaver Reader Door Lock Connectors WIRING PORT USAGE SEN GND BUT Door Sensor (SEN-GND) Release Button (BUT-GND) NO1 NC1 Dry Contact (Independent power supply for door lock) · NO type door lock (NO1-COM) · NC type door lock (NC1-COM) Power Contact (Using power from terminal to power on door lock) · NO type door lock (NO1-GND) · NC type door lock (NC1-GND) COM AL+ AL- Dry Contact (independent power supply for door lock) · NO type door lock (NO1-COM) · NC type door lock (NC1-COM) Power Contact (using power from terminal to power on door lock) · COM1 - +12V Alarm System The terminal will trigger the alarm output in the following situations: · Door forced open (A door sensor must be installed) · Door open time out (A door sensor must be installed) · Terminal has been illegally dismantled The AdapTec Plus is a 12VDC power supply inclusive of a 110~240VAC switching linear power. The AdapTec Plus supplies 12VDC power to the FingerTec terminal and door lock system as well as charges a 12VDC 7.0Ah backup battery simultaneously. During an event of a power failure, the back up battery automatically provides power to the terminal and maintains the door lock system. The AdapTec Plus also prevents a secured door from being opened if it has been tampered with. Door Lock Accessories FingerTec offers various door locks accessories to complement the door access product range. Diagram 3 · Printer / Bell / Siren Appendix II Terminal Dimensions and Measurements 85mm 19.80mm 143mm