Installation Guide for AMGO models including: LR06, LR06 Portable Low Rised Scissors Lift, LR06, Portable Low Rised Scissors Lift, Low Rised Scissors Lift, Scissors Lift, Lift
AMGO LR06 Low-Rise Lift
AMGO LR06 Low-Rise Lift – Equipment Outfitters
AMGO LR06 Low-Rise Lift — My Garage Supplies
Original Portable Low-rised scissors lift Model:LR06 CONTENTS Product Features and Specifications ........................................................... 1 Installation Requirement .......................................................................... 2 Step of Installation .................................................................................. 3 Exploded View ........................................................................................ 7 Operation Instructions ............................................................................ 13 Maintenance Schedule ........................................................................... 14 Trouble Shooting ................................................................................... 15 Lift disposal .......................................................................................... 15 I. PRODUCT FEATURES AND SPECIFICATIONS (See Fig.1) PORTABLE LOW-RISED MODEL LR06 · Self-locking safety device: 3 stage safety lock, mechanical lock, automatic release. · Portable unit is easy to move with the power unit stand · High speed: From 0-23 5/8" just 21 seconds · Standard rubber pads included Fig.1 MODEL LR06 SPECIFICATIONS Model Lifting Capacity Raised Height LR06 6000lbs 23 5/8" Lifting Time Overall Length Overall Lowered Runway Width Height Width Runway Length Motor 1.0 HP 21S 76 1/4" 70" 4 1/8" 18" 53 1/4" Single Phase 1 II. INSTALLATION REQUIREMENT A. Tools requirement Screw Set Grease gun Socket Head Wrench (8) Pliers Wrench sets(13151719 ) Fig.2 B. Power requirement The electrical source must be 1.0HP minimum. The source cable size must be 2.5mm² and in good condition of contacting with floor. 2 III. STEPS OF INSTALLATION A. Check the parts before assembly, make sure all the parts are completed. 1. Packaged lift, Parts box, Power Unit and Power Unit Stand. Move aside the parts, Open the outer packing and check the parts according to the shipment parts list (See Fig. 3). 33 Fig. 3 2. Open the parts box, check the parts according to the part list (See Fig. 4). Fig. 4 3 3. Check the parts of the parts bag according to the parts bag list (See Fig. 5). Fig. 5 B. Install hydraulic power unit (See Fig. 6) Fig. 6 4 C. Install fitting to power unit, and then connecting oil hose (See Fig.7). Fig. 7 5 D. Install electrical system Connect the power source on the data plate of power unit. Note: For the safety of operators, the power wiring must contact the earth well. Single phase motor 1. Circuit diagram (See Fig. 8) Fig.8 2. Connection step (See Fig. 9) Connecting the two power supply wires (active wire L and neutral wire N) to terminals of AC contactor marked L1, L3 respectively. Earth wire( yellow and green wire) is connected with the earth wire terminal of the motor Power supply wires Fig. 9 6 IV. EXPLODED VIEW MODEL LR06 Rollers Fig. 10 Fig. 11 7 PARTS LIST FOR MODEL LR06 Item Part# Description 1 11630001 Platform 2 10206019 Snap ring 19 3 11630003 Pin for drive-thru ramp 19*452 4 11630004 Drive-thru ramp 4A 10209010 Snap Ring 10 4B 11620043 Pin for roller of drive-in ramp 4C 10620063 Roller of drive-pin ramp (black nylon) 5 11630005 Connecting pin for cylinder 25*210 6 10630006 Cylinder 7 11630007 Cylinder base connecting pin 25*132 8 10206032 Snap ring 25 9 11630008 Frame support connecting pin (Upper) 19*356 10 11630009 Frame support (Front) 11 11630010 Frame support connecting pin (Lower) 19*405 12 11630011 Frame support (Rear) 13 10630100 Socket bolt M10*40 14 11630013 Safety block 15 11630014 Safety bar set 16 10420020 Hex bolt M10*110 17 10630015 Spring 15*12*55 18 10209022 Washer 10 19 10209056 Self Locking Nut M10 20 11640024 Rollers 21 10630102 Rubber block 438*1350*5 22 10620034 Rubber pad 120*100*38 23 11630012 Base frame 24 071103 Manual power unit 25 10209003 Hex bolt M8*25 26 10209005 Self Locking Nut M8 27 11640021 Power unit stand 28 10206006 Washer 12 29 10420046 Split pin 3*20 30 10209064 Straight Fitting 31 10630101 Oil hose 1/4*3650 32 10209060 90 Fitting for power unit 33 10630500 Parts Box PARTS FOR ROLLER 20-1 11630031 20-2 10630032 20-3 11630033 20-4 11630034 20-5 1003275021 Rollers handle Snap Ring 12 Connecting Shaft 12*80 Roller Shaft 12*65 White wheel QTY. 1 20 2 2 8 4 4 1 1 1 4 4 2 4 2 1 1 1 2 2 2 3 2 2 4 1 1 4 4 1 2 2 1 1 1 1 2 8 2 2 4 Note 8 Cylinder Item 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6-13 6-14 Part No. 11630029 11630026 10201034 11630030 10209078 10620058 10620049 11630028 10206069 10630027 10620054 10620055 10206071 10620064 Description Bore Weldment Piston Rod Bleeding Plug Head cap Dust ring O-Ring inside head cap O-Ring outside head cap Piston Small O-Ring for piston O-Ring outside piston Y-Ring OSI Support Ring Nut Greasing Fitting Fig. 12 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 2 Note 9 Manual Power Unit (071103) Fig. 13 10 Manual Power Unit 110V/60HZ Single Phase Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Part No. 81400180 81400250 81400200 10420148 81400066 81400363 80101013 10209149 81400276 81400259 85090142 81400312 10209034 81400295 81400365 10209152 85090167 81400290 81400412 10420070 81400559 81400287 71111211 81400560 81400266 81400284 10720118 81400451 10209020 81400421 81400422 81400449 81400567 81400566 81400375 81400376 81400364 81400263 81400320 Description Rubber pad Start capacitor Run capacitor Cap head bolt with washer Cover for capacitor Motor connecting shaft Manifold block Lock washer Iron plug Red rubber plug Socket bolt Gear pump Washer Socket bolt O-ring Belt Magnet Filter mesh Motor Button switch AC contactor Cover of motor terminal box AMGO label Throttle valve Release valve Iron plug Elastic pin Handle for release valve Plastic ball for arm lock Release valve nut Release valve shim Valve seat(Low) Release valve Check valve Oil suction pipe Oil return pipe Hose clamp (stainless steel) Oil tank cap Oil tank QTY. 2 1 1 4 2 1 1 4 1 1 4 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Note 11 Illustration of hydraulic valve for power unit Protective ring Oil return port Oil Outlet Release valve Handle for release valve Check valve Fig. 14 Relief valve Throttle valve Oil Outlet 12 V. OPERATION INSTRUCTIONS 1. Install the oil hose between oil cylinder and power unit, connect well the power supply wire. The machine can be ready to use. 2. The roller must be disengage when lifting vehicle (See Fig.17). To raise and lock the lift: Press the button up till the lift is raised to the required height and the locks are in engaged (See Fig.15), then push release handle of the power unit, the lift would be locked. 3. To lower liftPress the button UP, until the safety lock is in the released position (See Fig.16), lower lift by pushing lowering handle. Fig.15 Fig.16 4. Move lift: Pull up roller bracket, lock two roller to the lift with roller shaft. (See Fig. 16& 17 ). Moving the lift by the power unit stand. Roller Assy. disengaged Fig. 17 Roller Assy. engaged Fig. 18 13 1. There are four fixed holes in the machine, can fix the machine on ground by 3/4 X 5 1/2" anchor bolts (See Fig.19). Fig.19 VI. MAINTENANCE SCHEDULE Monthly: 1. Lubricate all moving parts with lubricant. 2. Check all connectors, bolts and pins to insure proper mounting. 3. Make a visual inspection of all hydraulic hoses/lines for possible wear or leakage. Every six months: 1. 1. Make a visual inspection of all moving parts for possible wear, interference or damage. 2. Check all fastener and re-torque. Oil cylinder maintenance: In order to extend the service life of the oil cylinder, please operate according to the following requirements. 1. Recommend to use N46 anti-wear hydraulic oil. 2. The hydraulic oil of the lifts should be replaced regularly during using. Replace the hydraulic oil 3 months after the first installation, Replace the hydraulic oil once a year afterwards. 14 3. Make at least one full trip raising and lowering per day. For exhausting the air from the system, which could effectively avoid the corrosion of the cylinder and damage to the seals caused by presence of air or water in the system. 4. Protect the outer surface of the oil cylinder's piston rod from bumping and scratching, and timely clean up the debris on the oil cylinder dust-ring and the piston rod. VII. TROUBLE SHOOTING TROUBLE Motor does not run CAUSE 1. Start Button does not work 2. Wiring connections are not in good condition 3. Motor burned out 4. AC contactor burned out REMEDY 1. Replace start button 2. Repair all wiring connections 3. Repair or replace motor 4. Replace AC Contactor Motor runs but the lift is not raised Lift does not stay up 1. Motor runs in reverse rotation 2. Gear Pump out of operation 3. Release Valve in damage 4. Relief Valve or Check Valve in damage 5. Low oil level 6. Overload or system low pressure 1. Release Valve out of work 2. Relief Valve or Check Valve leakage 3. Cylinder or Fittings leaks 1. Reverse two power wire 2. Repair or replace 3. Repair or replace 4. Repair or replace 5. Fill tank 6. Check load or adjusting the pressure of hydraulic system Repair or replace Lift raises slowly 1. Oil line is jammed 2. Motor running on low voltage 3. Oil mixed with air 4. Gear Pump leaks 5. Overload lifting 1. Clean the oil line 2. Check electrical system 3. Fill tank 4. Repair or replace pump 5. Check load Lift can not lower 1. Safety device are in activated 2. Release valve in damage 3. Oil system is jammed 1. Release the safeties 2. Repair or replace 3. Replace Clean the oil system VIII. Lift disposal. When the car lift cannot meet the requirements for normal use and needs to be disposed, it should follow local laws and regulations. 15 AMGO HYDRAULIC CORPORATION 1931 Joe Rogers Blvd, Manning, South Carolina, USA Tel: (803) 505-6410 Fax: (803) 505-6410 Manual Part No. : 722215602 Revision Date: : 2022/02 16WPS 文字