Installation Manual-MEAN WELL Switching Power Supply ManufacturerProduct Liability Disclaimer-MEAN WELL Switching Power Supply Manufacturer
Owner's Manual for MEAN WELL models including: IDLV-45 Series 45W IDLV Series Constant Voltage PWM LED Driver, IDLV-45 Series, 45W IDLV Series Constant Voltage PWM LED Driver, Constant Voltage PWM LED Driver, Voltage PWM LED Driver, PWM LED Driver, LED Driver
45W IDLV Series Constant Voltage PWM LED Driver - Marvel Lighting
File Info : application/pdf, 6 Pages, 961.39KB
DocumentDocument45W PWM Output LED Driver
IDLV-45 series
User's Manual
IS 15885(Part 2/Sec13)
THOMAS SAMUEL
THOMAS SAMUEL
R-41027766
(for IDLV-45-12,24,48 only)
A
File Name:IDLV-45-SPEC 2022-02-14
45W PWM Output LED Driver
IDLV-45 series
SPECIFICATION
MODEL
IDLV-45 -12
IDLV-45 -24
IDLV-45 -36
IDLV-45 -48
IDLV-45 -60
OUTPUT
DC VOLTAGE
12V
24V
36V
RATED CURRENT
3.0A
1.88A
1.25A
RATED POWER
36W
45.12W
45W
DIMMING RANGE
0~100%
VOLTAGE TOLERANCE
±10%
PWM FREQUENCY (Typ.)
1KHz(±20%)
SETUP TIME Note.3
500ms / 230VAC 1200ms/115VAC
AUXILIARY DC OUTPUT Note.4 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only
VOLTAGE RANGE Note.2 90 ~ 295VAC (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE 47 ~ 63Hz
48V 0.94A 45.12W
60V 0.75A 45W
POWER FACTOR (Typ.)
PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VAC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION" section)
EFFICIENCY (Typ.)
84%
86%
88%
88%
90%
AC CURRENT (Typ.)
0.6A / 115VAC 0.4A / 230VAC 0.3A / 277VAC
INRUSH CURRENT(Typ.) COLD START 30A(twidth=150s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD POWER CONSUMPTION <0.5W for Blank-Type, <1.2W for A-Type
SHORT CIRCUIT
Shut down O/P voltage, re-power on to recovery
PROTECTION OVER CURRENT
105 ~ 115% Protection type : Hiccup mode, recovers automatically after fault condition is removed
WORKING TEMP.
Tcase=-20 ~ +85 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section)
MAX. CASE TEMP.
Tcase=+85
ENVIRONMENT WORKING HUMIDITY
20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 40)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750,CSA C22.2 NO.250.13-12; BS EN/EN/AS/NZS 61347-1 & BS EN/EN/AS/NZS 61347-2-13 independent, BS EN/EN62384,BIS IS15885(for IDLV-45-12,24,48 only), EAC TP TC 004 approved
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC
EMC
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH
EMC EMISSION
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load60%) ; BS EN/EN61000-3-3, EAC TP TC 020
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity:Line-Line:1KV), EAC TP TC 020
MTBF
386.59Khrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION
120*75*25mm (L*W*H)
NOTE
PACKING
0.22Kg;54pcs/13Kg/ 0.93CUFT
To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains. , https://www.meanwell.com/serviceDisclaimer.aspx
File Name:IDLV-45-SPEC 2022-02-14
45W PWM Output LED Driver
DIMMING OPERATION
ACL
ACL ACN
TB1
ACN
DIM+
DIMVo+
TB2
Vo-
IDLV-45 series
Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current.
ON Output DC current
Io=0A
OFF TON
T
TON
Duty cycle(%) =
×100%
T
Output PWM frequency : 1KHz(±20%)
2 in 1 dimming function Applying additive 0 ~ 10VDC
Vo+ +
+
Vo-
-
DIM+ +
Additive Voltage DIM-
"DO NOT connect "DIM- to Vo-"
Applying additive 10V PWM signal (frequency range 300~3000Hz):
Vo+ +
+
Vo-
-
DIM+
Additive PWM signal
DIM-
"DO NOT connect "DIM- to Vo-"
Duty cycle of output current (%)
Duty cycle of output current (%)
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0% 0V 1V
2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Note : 1. Min. duty cycle of output current is about 8% and the output current is not defined when 0%< Iout<8%. 2. The duty cycle of output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
File Name:IDLV-45-SPEC 2022-02-14
45W PWM Output LED Driver
IDLV-45 series
OUTPUT LOAD vs TEMPERATURE
LOAD (%)
100
80 70 60
40
20
-20 -10 0
10
20
30
40
AMBIENT TEMPERATURE,Ta ()
100
80 70 60
40
20
LOAD (%)
(HORIZONTAL)
-20 -10 0
15
30
45
60
85
Tcase ()
(HORIZONTAL)
LOAD (%)
STATIC CHARACTERISTIC
100
90
for 12V model
80
70
for others
60
50
40
90 100
135
180 200 230
295
INPUT VOLTAGE (V)
De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 75
1.00
0.95 0.90 0.85
277(45W) 230(45W) 115(36W)
0.80
0.75
50%
60%
70%
80%
90%
100%
LOAD
TOTAL HARMONIC DISTORTION (THD)
60V Model,Tcase at 75
19.00%
17.00%
15.00%
13.00%
11.00%
9.00%
7.00%
5.00%
50%
60%
70%
80%
90%
LOAD
277(45W) 230(45W) 115(36W)
100%
EFFICIENCY(%)
EFFICIENCY vs LOAD
IDLV-45 series possess superior working efficiency that up to 90% can be reached in field applications. 60V Model,Tcase at 75
91%
90%
89%
277(45W)
230(45W)
88%
115(36W)
87%
86%
85%
50%
60%
70%
80%
90%
100%
LOAD
File Name:IDLV-45-SPEC 2022-02-14
THD(%)
45W PWM Output LED Driver
BLOCK DIAGRAM
IDLV-45 series
fosc : 70~150KHz
EMI FILTER
I/P
&
RECTIFIERS
POWER SWITCHING
O.L.P.
PWM&PFC CONTROL
RECTIFIERS
RECTIFIERS &
FILTER
CURRENT LIMIT
DETECTION CIRCUIT
AUX+(for A-Type) AUX-(for A-Type)
Vo+ VoDIM+ DIM-
75
6.5
MECHANICAL SPECIFICATION
Blank-Type
120 6.5
6.5
6.5
Case No.IDLC-45A Unit:mm
tc : Max. Case Temperature
1
2 3
TB1
4
1
2 3
TB2
4
tc 30
30
3
25
NOTE: Please use wires with a cross section of 0.75~1.5mm2 for TB1 and wires with a cross section of 0.5~1.5mm2 for TB2.
Terminal Pin No. Assignment(TB1)
Pin No. Assignment
1
ACL
2
ACL
3
ACN
4
ACN
Terminal Pin No. Assignment(TB2)
Pin No. Assignment
1
DIM+
2
DIM-
3
Vo+
4
Vo-
File Name:IDLV-45-SPEC 2022-02-14
45W PWM Output LED Driver
A-Type
120 6.5
75
6.5
6.5
6.5
30
IDLV-45 series
tc : Max. Case Temperature
1
2 3
TB1
4
1 2 3 TB2 4 5 6
tc 30
3
25
NOTE: Please use wires with a cross section of 0.75~1.5mm2 for TB1 and wires with a cross section of 0.5~1.5mm2 for TB2.
Terminal Pin No. Assignment(TB1)
Pin No. Assignment
1
ACL
2
ACL
3
ACN
4
ACN
Terminal Pin No. Assignment(TB2)
Pin No. Assignment Pin No.
1
DIM+
4
2
DIM-
5
3
Vo+
6
Assignment VoAUX+ AUX-
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
File Name:IDLV-45-SPEC 2022-02-14