PATPET TK16 1600ft Remote Training Collars Instruction Manual

Instruction Manual for PATPET models including: TK16, TK16 1600ft Remote Training Collars, 1600ft Remote Training Collars, Remote Training Collars, Training Collars, Collars

Manual EN

Patpet TK16 - Training collars - Electric-Collars.com

1600ft Remote Training Collar

Transmitter Patpet TK16 - Transmitters - Electric-Collars.com

File Info : application/pdf, 16 Pages, 900.55KB

16955-patpet-tk16-en

1600ft Remote Training Collar
MANUAL BEFORE BEGINING Please read the user manual carefully before use. If the product you got is not suitable or damaged, please contact us immediately. We will give you a satisfactory reply.
1

1. Make sure the remote and receiver are full charged before using for the first time 2. Please use vibration or tone mode first. Shock mode is only recommended in emergency situation and not advised as a form of positive behavior training. 3. Start at the lowest level of shock mode then slowly turn to the next level until the dog has a response. And if your dog becomes uncomfortable, please stop using immediately. 4. Please check the skin condition of dog's when wearing the receiver collar. If there is any skin injury, please stop using immediately until the dog recovers. 5. Please don't keep receiver collar on dogs for more than 4 hours at a time. 6. Contact points are made of silicone; most dogs can wear it comfortably. If some dogs are allergic to silicone or feel uncomfortable with collar, please stop using it and consult a veterinarian. Note: This product is only suitable for training and is banned for animal abuse.
2

Content
Warning.................................................................................2 Package List............................................................................4 Usage Instruction....................................................................5
Main Functions...................................................................5 Functions Instruction................................................................6
Remote Range...................................................................6 Outdoor Waterproof.............................................................6
Static Shock......................................................................7 Vibration & Beep................................................................8 Sleep Mode.......................................................................8 Button Definition.....................................................................9 LCD Screen.......................................................................9 Turning up & off and Indicator..................................................10 Product Synchronizing............................................................11 Fit the collar..........................................................................13 Charging & Battery.................................................................14 Charging ........................................................................14 Battery..........................................................................14 Trouble Shooting..............................................................15
3

Package List
4

Usage Instruction Main Functions
Static Shock: 16 adjustable intensity levels Vibration: 16 adjustable intensity levels Beep: tone warning WaterproofIP67 full waterproof receiver collar Safe Screen-lockAvoid pressing buttons by accident
Fast Charging2-hour full charging
5

Functions Instruction
Remote Range · This item uses 433MHz frequency to send and receive signals, the theoretical range is up to 1600ft. · The distance is used in most dog training environments such as indoor, courtyard, parks, streets and so on. · The received signal distance may be shortened due to interference from the environment, weather, and obstacles. · When the remote sends a signal, you should hold it to protect it from obstacles. If you use it inside or under your pocket, it will also affect the distance.
Outdoor Waterproof · This receiver collar achieves IP67 waterproof performance · Safe for dog to wear during rain and fog · Safe to be immersed in water up to 1 meter deep · Do not immerse in water for more than one hour
6

Static Shock · Before using for the first time, you can use the test bulb to test whether the current is normal. · Different dogs have different resistance values. You can gradually use the equipment when you start to use it to find the appropriate electric shock level for your dog. · For initial use, select the minimum current for the pet to adapt and watch his reaction. If any adverse reactions occur, please stop immediately. · The current range of this product is divided into 1-16 levels, which is suitable for all kinds of education and punishment environment. The recommended usage values of 1-16 levels are as follow. · The use of static shock of this product is limited to proper education, and all non-standard use and abuse of pets are strictly prohibited.

Level 1-3 It can be used for warning

Level 4-6 It can be used for punishment

Level 7-10 It can be punishment and deterrence

Level 11-16

It can be used to stop the current behavior in an emergency

(Different volumes of dogs or breeds have different reactions. The above are recommended methods for reference only)
7

Vibration & Beep · Before using the static shock, you can use the sound and vibration first, which allows the dog to form a conditioned reflex, and stops the current wrong behavior before feeling the vibration or sound. It is the safest method of training. · You can combine reward training to train your dog to make a series of actions after feeling vibration or sound. · The gear for vibration is divided into 1-16 files, and the intensity of the sound is not adjustable.
Sleep Mode · Sleep mode normally used for dogs short breaks, or when sleeping, no manual shutdown is required. After no operation for 30 seconds, it enters sleep mode and maintains extremely low power consumption. · Just pressing any button on the remotecan be wake it up. When you launch a command signal by remote, you can wake up the receiver
8

Button Definitions

LCD Screen

Beep mode Vibration mode Shock mode Show receivers in using If keeping 2 receivers Screen-lock state Intensity level Power state of remote
9

Turning up & off and Indicator Screen-lock button Push down to unlock buttons. Push up to lock buttons and turn it off, and any other buttons can't activate remote. Turning on/off receiver: ON: The receiver vibrates and is accompanied by a sound. OFF: Press power button, it will make a long beep. Operation Indicator The green indicator lights up and keeps flashing every 2 seconds that when receiver turned on and entering working state. During synchronizing state, it will flickering alternately red and green. Power Indicator Less than 20% power, The red LED Light will flashing. When receiver chargingThe red LED Light will keeps on and turns green when it's fully charged.
10

Product Synchronizing This product works by radio channel. Only do remote transmitter and receiver keep on the same channel, they can work synchronously . Before delivery, we will complete synchronizing. If remote lost contact with receiver because of signal interrupt and power outage, please synchronize by hand.
How to manually pair the receiver and remote when they lost contact
Step 1: Turn on the Remote Press the any button to turn on the Remote. Please unlock the remote first, If the remote is locked.
Step 2: Choose dog channel.

Set 1/2 button on remote, select or on LCD screen. It means receiver will be controlled by channel 1 or 2. (see picture 1 and

picture 2)
11

Step 3: Turn on the receiver Press the power button to turn on the receiver (see Picture 3), and the LED indicator on the receiver will flash (see Picture 4)

Step 4: Remote receiver signal to complete synchronizing.

Press the power button and hold for 3 seconds, the LED indicator on

the receiver will flickering alternately red and green (see picture 5).

The receiver is ready for pairing, then press the vibration and Beep

button at the same time, and a beep from receiver means

synchronizing finishes. Now please start to enjoy your dog training

collar.

PS: If you buy 2-dog system, you can pair the two collars on channel

1 and channel 2 separately. Follow step 1 to synchronize two

receivers separately. You can use 1/2 button on the remote to control

different dogs separately.

Fit the collar
1. Make sure your pet is standing comfortably to fit it correctly(3A). 2. Place receiver collar on the middle of your pet's neck and avoid it being loose(3B).
3. Adjust the most comfortable collar length to your dog, do not too loose or too tight. It should be left 2 fingers between the collar and dog's neck(3C). 4. Please check whether contact points touch dog's neck. If dog's fur is too long, please change longer contact points or trim the fur, otherwise, shock won't work (because fur is a nonconductor.) 5. The receiver is ABS plastic and compound rubber, please prevent dog from biting. 6. Contact points are made of silicone and most dogs can wear it comfortably. If some dogs are allergic to silicone or feel uncomfortable with collar, please stop to use it and consult a veterinarian.
13

Charging & Battery Charging
1. Please do not use an adapter larger than 5V2A to charge the product. 2.You can also charge the product through the USB port of your car, laptop,desktop computer or power bank. 3.When the receiver is low on power,the indicator light on the receiv er turns red,please charge it as soon as possible. 4.Please unplug the power supply as soon as possible after full char ge to avoid long-term charging. 5.Do not expose the power cord to rain or snow, and do not trample or squeeze it to avoid damage. 6.The charging time is about 2 hours.
Battery 1.Do not leave the product in excessive temperature for a long time. When the battery is in an environment exceeding 60 degrees Celsius for a long time, it is possible to explode and cause danger to life. 2.When the device shows low power, charge it as soon as possible. Do not recharge before the battery is run out. 3.After full charge, please remove the power supply as soon as possible to avoid prolonged charging. 4.When the battery is damaged, do not repair or disassemble it.
14

Trouble Shooting

·Make sure the Receiver Collar has been turned on.

·Check if you are currently in a paired channel,

My pet does not press the 1/2 button to select the channel you want

respond when I to control.

press a button. ·If both channels cannot be controlled, check

whether they are currently in a matching state. You

can manually rematch them. For details, see Pairing

and Hibernation Pairing.

Why the remote ·The current environment may have obstacles that

range can't

affect the signal distance.

reach actual

·Signal interference may exist in the current

distance?

environment.

How to know if ·When the transmitter and receiver are working, it

the shock works will light up.

or not?

·You can use the test light to test if it works.

·Try to increase the level of the electric shock.

·Check that the wear is correctly, the two contacts

are positive and negative, and it is necessary to

touch the dog's skin at the same time.

What if dogs

·Depending on the length of the dog's hair, it is

have no

possible to increase the length of the contacts or to

response for the remove some of the dog hair.

shock?

·Insufficient current from the receiver or

transmitter can also affect the shock function.

YBS234 MADE IN CHINA
15

The device has been approved for use in EU countries and is therefore provided with the CE mark. All necessary documentation is available on the website: www.electric-collars.com Changes to technical parameters, properties and printing errors reserved.
Service center and distribution Reedog, sro Sedmidomky 459/8 101 00 Prague 10 Phone: +1 646 980 4569 Email: info@electric-collars.eu

References

PDF24 PDF24