Installation Guide for HD Ridez models including: WB-FR188BD Overland Slider Drop Steps, WB-FR188BD, Overland Slider Drop Steps, Slider Drop Steps, Drop Steps
HD Ridez Overland Slider Drop Steps Compatible with Ford F150 2015-2024 Super Cab & F-250 F-350 Super Duty 2017-2024 : Automotive
INSTALLATION INSTRUCTIONS RS6 OVERLAND SLIDER DROP STEPS 2015-24 FORD F150 SUPER CAB 2017-24 F250/350/450/550 SUPER DUTY SUPER CAB PART#WB-FR188BD PARTS LIST: RS6 OVERLAND SLIDER DROP STEPS 2015-24 FORD F150 SUPER CAB, 2017-24 F250/350/450/550 SUPER DUTY SUPER CAB 1 Driver/Left Tube 8 10mm Nylon Lock Nuts 1 Passenger/Right Tube 8 8mm x 25mm Triangle Double Bolt Plates 4 Drop Steps 12 8mm x 24mm OD x 2mm Flat Washers 4 Mounting Brackets 16 8mm x 22mm OD x 2mm Flat Washers 8 10mm x 30mm Hex Bolts 28 8mm Nylon Lock Nuts 16 10mm x 20mm OD x 2mm Flat Washers 12 8mm Plastic Retainers (4) Mounting Brackets Front Driver/Left Overland Step (4) Drop Steps PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. 1. Start the installation under the Driver/Left side of the vehicle. Locate the front mounting location along the inner side of the body, (Figure 1). 2. Slide (1) Plastic Washer over each of the (3) factory mounting studs in the body panel, (Figures 2 & 3). IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers. 3. Select (1) Mounting Bracket. NOTE: All (4) Brackets are universal and will fit left or right side. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figure 4). Leave brackets loose at this time. 4. Repeat Steps 1--3 to attach (1) Mounting Bracket to the rear location, (Figure 5). 5. Select the Driver/Left Tube. Insert (2) 8mm Triangle Double Bolt Plates into the front (2) sets of (2) holes, (Figure 6). Attach (1) Drop Step to the (2) Double Bolt Plates with (4) 8mm x 22mm Flat Washers and (4) 8mm Nylon Lock Nuts, (Figure 7). Do not tighten hardware. 6. With assistance, line up the mounting tabs in the Driver/Left Tube to the rear faces of the Mounting Brackets. Secure the Tube to the Mounting Brackets with (4) 10mm Hex Bolts, (8) 10mm x 20mm Flat Washers and (4) 10mm Nylon Lock Nuts, (Figure 8). Do not tighten hardware. 7. Level and adjust the Overland Step, then tighten all hardware. 8. Repeat Steps 1--7 to attach the Passenger/Right Step. 9. Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Overland Steps. Page 1 of 3 9/12/22 (EL) RS6 OVERLAND SLIDER DROP STEPS 2015-24 FORD F150 SUPER CAB, 2017-24 F250/350/450/550 SUPER DUTY SUPER CAB Driver/Left Side Installation Pictured Front (Fig 1) Driver/Left front mounting location Rear (3) Plastic Insulation Washers (Fig 2) Plastic Insulation Washer (Fig 3) Thread Plastic Washers onto all mounting studs. (Passenger side rear mounting location pictured) (3) 8mm Plastic Washers (3) 8mm x 24mm Flat Washers (3) 8mm Nylon Lock Nuts (Fig 4) Attach (1) Mounting Bracket to the front mounting location Page 2 of 3 9/12/22 (EL) RS6 OVERLAND SLIDER DROP STEPS 2015-24 FORD F150 SUPER CAB, 2017-24 F250/350/450/550 SUPER DUTY SUPER CAB Driver/Left Side Installation Pictured Rear (Fig 5) Driver/Left rear mounting location 8mm Bolt Plate (2) 8mm x 22mm Flat Washers (2) 8mm Nylon Lock Nuts (Fig 6) Insert (1) Bolt Plate into the holes in the Tube (Fig 7) Attach (1) Drop Step to (2) Bolt Plates (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts (Fig 8) Attach the Driver/Left Running Board to the Mounting Brackets Page 3 of 3 9/12/22 (EL)WPS 文字