Download – ATOMRC
User Manual for EACHINE models including: Atomrc Seagull Fpv Bundle
ATOMRC Seagull FPV Bundle, the ATOMRC EXCEED TOWER have compact size and powerful feature, F405 FC and 500mW VTX. The ESC ...Missing: 2021 | Must include: 2021
File Info : application/pdf, 9 Pages, 16.26MB
DocumentDocumentSeagull FPV Bundle User Manual 2021.5 Intro ATOMRC Seagull FPV Bundle, the ATOMRC EXCEED TOWER have compact size and powerful feature, F405 FC and 500mW VTX. The ESC can support 35A for 60s environment 25. The ATOMRC PHOTON 2004 2700KV MOTOR have max 634g thrust, give more maneuverability for drones. Flight time with standard 4S 850mah battery is 9 min, user change use bigger battery for more flight time. The Cobra L FPV goggles have 4.3 inch 480*272 LCD Screen, integrated with DVR, goggles have diversity receiver for stable image reception, goggles can power by 18650 battery or USB C. The T8 lite radio have ergonomic design and 4 aux switch,support multiple mode. Packing list Seagull FPV Racing drone*1 Cobra L FPV FPV Goggles*1 T8 Lite Radio*1 Cobra L accessories*1 Seagull Bundle user manual*1 Charger*1 4S Lipo Battery*1 Seagull Basic Manuel 1Make sure nothing is blocked the props when power on. 2User can change the settings on Betafight ground station. 3Before flight, please make sure know the arm switch and mode switch, if the drone out of control, please disarm the drone immediately, the prop will stop spinning. (radio content below) 4User 4S 850mah battery, flight time about 9min,with naked gopro flight 7min full size gopro about 6 min. 5If the battery voltage below 14.5V, there is no much power remain, user need land the drone to avoid crash and over discharge. 6Angle mode: the drone will self-level when release the sticks. Self-level modes are easier to fly for beginner. 7Air mode, there is no angle limit for the drone, drone will have much more maneuverability, this mode is for advanced fight. Cobra L USER MANUEL SPECS MODEL Screen Resolution FOV Aspect Ratio Receiver Power Supply Power Consuption DVR SIZE Weight COBRA L LCD 480*272 50° 16:09 5.8Ghz 48 CH Diversity RX 18650/USB 5V 5V 0.5A H264, 30fps,MOV 6Mbps, Max 32Gb 122*165*100mm 330g Frequency Table BAND/CH CH 1 A 5865M B 5733M E 5705M F 5740M R 5658M L 5362M Sensitivity Antenna Port CH2 5845M 5752M 5685M 5760M 5695M 5399M BAND/CH table CH3 CH4 CH5 5825M 5805M 5785M 5771M 5790M 5809M 5665M 5645M 5885M 5780M 5800M 5820M 5732M 5769M 5806M 5436M 5473M 5510M -98dBm±1dBm 2 X SMA-K,50ohm CH6 5765M 5828M 5905M 5840M 5843M 5547M CH7 5745M 5847M 5925M 5860M 5880M 5584M CH8 5725M 5866M 5945M 5880M 5917M 5621M Button Function 3 2 1 6 GND Video Audio R Audio L AV connector Pin out 5 4 7 8 1.Power 3.CH/BAND/Search 5.Mode 7.SD card connector Goggles Menu 2.Menu 4.Record/Delet 6.USB C Connector 8.Audio/Video connector 1Install the 18650 battery. 2Long press the power on button to power on. 3Press the right wheel, then roll the right wheel to change channel, press the wheel again switch to band setting mode, then roll the wheel to change the band. 4Hold the righ wheel to search, it will take 20s to search. 5Sometime the auto search channel is not accurate, user may need manually select the channel. 6DVR need SD card to record, please format SD card to FAT32. 7When goggles receive image, press record buttonthe DVR icon will flash, press record button again to stop recording. 8Short press left wheel, when OSD show PBPlay Back Mode, roll right wheel to select, press right wheel to record or fast forward . 9press mode button to quit play back mode. 10Goggles OSD is below. 1 2 RF BAND:A CH:1 5865MHz 4 5 3 L: R: 6 3.8V 7 15.2V 8 00:08 10 2.1A 9 1.DVR Status 2.SD Card Status 3.Battery Status 4.Mode 5.Frequency 6.RSSI 7.Drone Battery voltage per cell 8.Drone Battery voltage 9.Drone Current 10.Flight Time The Goggles OSD time out can be set, turn off means the OSD is always on. Radio 1Make sure all switch is down, throttle stick is at the bottom. 2Hold power button is turn on, the LED will turn green. 3If the green LED is flashing and radio start beep, it means that Switch is not down or throttle stick is not bottom. push switch down and throttle to bottom, the radio will back to normal. 4The radio can charge by USC C port 5V. Flight Mode Push up SC Switch to Arm the quad, the prop will spinning. SC SD SC Push up SD Switch Angle mode to Air Mode. SA Switch is buzzer switch, drone will beep when pull up this switch. SB is anti flip switch, when drone is flipped, pull up this switch then push sticks, drone will flip back to normal. Stick mode Mode 2 Left Stick Mode 1 Right Stick Left Stick Right Stick Push the throttle Stick upward, the drone will fly upward. Push the Yaw Stick right, the drone will rotate horizontal clockwise. Push the Pitch Stick upward, the drone will tilt down. Push the Roll Stick left, the drone will roll left. How to Bind RX 1. Hold the BIND button on the receiver and turn on the power .After about 3 seconds, the receiver LED red light will be on. And wait for the link. 2. Keep the throttle stick at the lowest position, and then press the link button for more than 1 second to bind the receiver. The power button will flash, indicating that linking is in progress. 3. At this time, the red light of the receiver flashes to indicate that the linking is successful, and the receiver can be used after powering on again Special. Attention: different D8 protocol receivers may enter the pairing mode in different ways. For details, please refer to the corresponding manuals of various receivers to ensure correct use. Various different receivers and models will have different methods to place the model or receiver in to bind mode. Please follow the instructions from the model or receiver manufacturers user manual to in. Pre fight Check 1Make sure droneradio and goggles batter are fully charged. 2Make sure familiar with stick mode and switch mode function. 3Make sure the goggles received the image, and image is clear. 4Ensure the prop is properly installed, no damage on prop. 5Turn on the radio and Goggles. 6Use battery strap to tie the battery, make sure no slide. 7Plug the battery, and put the drone to the level ground. 8Now the drone is ready to fly. 9If not familiar with the drone, use angle mode first. Flight Environment 1Do not fly in windy or snow and rain days. 2Choose open area, no crowds and cars near by. 3Keep away from crowds powerline water radio tower etc. 4Do not fly over height. Chager And Maintain 1Charger support 110~220V AC IN. 2For safety do not charge the battery unattended . 3To reserve the battery, make sure battery is not fully charged, discharge battery to 14.8V . FAQ Cant Arm? Check throttle stick, make sure it at bottom, make sure quad is level. How to install prop? The prop is spinning from inside to out size, prop is locked by M2*8mm Hex screw. Goggles screen black? Make sure its in RF mode, press left wheel to switch. How to change the Frequency? The VTX have IRC protocol, user can change it with osd command. ATOMRC Seagull RTF Bundle Flight Controller ESC Motor VTX Cam Prop Resolution Receiver DVR POWER Frequency Channel Protocal Drone ATOMRC Exceed F405 MINI ATOMRC Exceed 30A MINI BLS 2~4s 4in1 ATOMRC 2004 2700KV ATOMRC Exceed 500mW MINI Foxeer Razer nano Gemfan 90mm COBRA L Goggles 480*272 Diversity MJPEG 1 Cell 18650/ USB C RADIO 2.4Ghz 8 D8 Please download the latest user manual at www.atomrc.com/pages/download