Installation Guide for Custom Dynamics models including: CD-ALT-BS-UNV Universal Alternating Brake Strobe, CD-ALT-BS-UNV, Universal Alternating Brake Strobe, Alternating Brake Strobe, Brake Strobe
Custom Dynamics Alternating Brake Light Strobe Module - RevZilla
Custom Dynamics Alternating Brake Light Strobe Module - Cycle Gear
prieš 3 dienas — We thank you for purchasing the Custom Dynamics Alternating. Brake Strobe Module. Our products utilize the latest technology.
Custom Dynamics® Alternating Brake Strobe Module Installation Instructions We thank you for purchasing the Custom Dynamics® Alternating Brake Strobe Module. Our products utilize the latest technology and high quality components to ensure you the most reliable service. We offer one of the best warranty programs in the industry and we back our products with excellent customer support, if you have questions before or during installation of this product please call Custom Dynamics® at 1(800) 382-1388. Part Numbers: CD-ALT-BS-UNV Package Contents: - Alternating Brake Strobe Module (1) - Adapter Harness (1) - Wire Ties (10) Fits: 12VDC negative ground systems. ATTENTION Please read all Information below before Installation Warning: Disconnect negative battery cable from battery; refer to owner's manual. Failure to do so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on vehicle. Safety First: Always wear appropriate safety gear including safety glasses when performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Be sure vehicle is on level surface, secure and cool. Important: This product is designed and intended for use as auxiliary lighting only. It is NOT intended to replace any original equipment lighting installed on the vehicle and should not be used for that purpose. This product must be wired so that it does not interfere with any original equipment lighting. Important: Do not exceed 3 Amps per output. Installation: 1. Secure motorcycle on level surface. Remove seat. Disconnect negative battery cable from the battery. 2. Locate and unplug the rear fender lighting harness connector. 3. Connect the Adapter Harness into the rear fender lighting harness. Adapter Harness MUST be installed in front of any Run/ Brake/Turn module or Taillight Brake Strobe module. Refer to the Input Wiring Schematic on Page 2. Plug the Alternating Strobe Module into the Adapter Harness. 4. For plug-n-play installation, install Custom Dynamics® Red LED BoltzTM (sold separately). Once the LED BoltzTM are installed connect them to the left and right output white 3 pin connectors. 5. For custom installations, remove the White 3 wire connectors from both outputs. Refer to the Output Wiring Schematic on Page 2 for connections. 6. Re-connect the battery's negative battery cable to the negative of the battery. 7. With the power off to the module, select the desired Brake Strobe Pattern using SW1 and SW2 switches. Refer to the Brake Strobe Pattern Information on Page 2. 8. Locate a secure place for the Alternating Strobe Module that will not interfere with the secure placement of the seat or side cover. Secure with tie-wraps, tape or other means so that unit will not move. 9. Test all lighting for proper operation. Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST 05/2022 Installation Instructions - Page 2. Input Wiring Schematic Adapter Harness Running Light Circuit Brake Circuit Ground Yellow Posi-TapTM Connector White Black Input ON OFF ON OFF SW-2 SW-1 9 01 8 2 7 3 65 4 DIAL Output Wiring Schematic ON OFF ON OFF SW-2 SW-1 9 01 8 2 7 3 65 4 DIAL Output: Right Side Brown Black Blue Constant 12Vdc Output Ground Strobe Output Purple Black Blue Constant 12Vdc Output Ground Strobe Output Output: Left Side NOTE: Do not exceed 3 Amps per output. Brake Strobe Pattern Information Adapter Harness Input Alternating Strobe ON OFF ON OFF SW-2 SW-1 9 01 8 2 7 3 65 4 DIAL Output: Right Side Output: Left Side · Dial controls the speed of the brake strobe. 0 being the slowest and 9 being the fastest. · SW-1 and SW-2 Selects the Brake Strobe Pattern: SW-2 SW-1 ON OFF ON OFF Random Brake Strobe Pattern ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF Alternating 2 Flash Pattern Alternating 4 Flash Pattern Alternating 5 Flash Pattern Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST 05/2022Microsoft Publisher for Microsoft 365