Guide Sensmart TD Series Thermal Imaging Cameras Quickstart Guide

Introduction

Thank you for purchasing this product. Please read this Guide first and keep it properly for future reference. The picture is for reference only, the product shall prevail in kind.

Important Information

IMPORTANT

Thank you for purchasing this product. Please read this Guide first and keep it properly for future reference. We hope this product will meet your expectations. This Guide is a general guide for a series of products, which means that the product you receive may differ from the description in the Guide. The actual product you receive shall prevail. This Guide is prepared to introduce our products to the users. We will try our best to ensure the accuracy of the Guide, but the completeness of the Guide still cannot be guaranteed, because our products have been continuously upgraded. We reserve the right to modify at any time without prior notice.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Notes and Warnings

DANGER

1. Please follow the method described in this Guide for charging the cell, and follow the charging procedures and precautions. Improper charging may cause overheating, damage and even personal injury; Do not attempt to open or disassemble the cell at any time. If any liquid touches the eyes in case of cell leakage, please rinse with clean water immediately and seek medical care.

WARNING

1. Please keep the device as stable as possible to avoid violent shaking.
2. Do not use or store the device in an environment with the temperature higher than the permitted level.
3. Do not expose the device directly to high-intensity heat radiation source, such as the sun, laser, spot welding machine, etc.
4. Do not block the holes on the device.
5. Do not knock, throw or vibrate the device and accessories to avoid damage.
6. Do not disassemble the unit by yourself, which may cause damage to the device and loss of warranty rights.
7. Do not use soluble or similar liquid on the device and cables, which may cause damage to the device.
8. Please do not use the device in an environment with the temperature higher than the permitted level, which may cause damage to the device.
9. Please observe the following rules when wiping this device:
   • Non-optical surface: if necessary, use a clean and soft cloth to wipe the non-optical surface of the thermal imaging camera.
   • Optical surface: avoid soiling the optical surface of the lens when using the thermal imaging camera, and especially avoid touching the lens with your hand, because the optical coating on the glass surface may be corroded due to sweat on the hands. When the optical lens surface is contaminated, use a professional lens cloth to carefully clean it.
10. Do not put the cell in a high temperature environment or near high-temperature objects.
11. Do not short-circuit the positive and negative terminals of the cell.
12. Do not place the cell in a humid environment or the water.

NOTES

1. Do not expose the device to dust or moisture. When used in an environment with water, avoid splashing water on the device. The lens shall be covered when the device is not in use.
2. When this device is not used, please place the device and all accessories in the special packing box.

List of Parts

Visual description of parts:

• BAG: A drawstring pouch.
• 18650 CELL: A cylindrical battery.
• MICRO USB CABLE: A cable with a Micro USB connector on one end and a standard USB-A connector on the other.
• VIDEO CABLE: A cable for video output.
• WRIST STRAP: A strap to secure the device to the wrist.
• 18650 CHARGER: A charger for the 18650 cell.

Product Components

This Guide is applicable to several models of this series, and the illustration is only for one of them.

Diagram Description: The diagram shows the thermal imaging camera with various buttons and ports labeled.

• CELL COVER BUTTON: Button to access the battery compartment.
• COLOR PALETTES BUTTON: Button to change color display modes.
• BRIGHTNESS BUTTON: Button to adjust screen brightness.
• POWER BUTTON: Button to turn the device on/off.
• FOCUS RING: Adjustable ring around the lens for focusing.
• ZOOM-IN BUTTON: Button to zoom the image.
• LASER: Indicates the presence of a laser pointer.
• LENS COVER: Protective cover for the camera lens.
• PERIPHERAL INTERFACE: A port for external connections.
• DIOPTER REGULATION: Adjustment for eyepiece focus.
• VIDEO AND EXTERNAL POWER SUPPLY INTERFACE: Port for video output and external power.
• CAMBOX PORT: A 1/4-inch standard port.

Quickstart Instructions

Button Operations

Button Descriptions

1. POWER BUTTON

• Power on: Long press and hold the power button until the startup picture appears in the eyepiece, then the device can be switched on successfully.
• Power off: Manual power-off: long press and hold the power button, the power-off progress bar will be displayed, and the power-off succeeds after the progress bar is finished. Automatic power-off: in the set automatic power-off time, without any button operation, the automatic power-off succeeds.
• Display off: Press and hold the power button, the progress bar of power-off will be displayed. Before the progress bar is finished, the power-off will be canceled and the Display off mode will be entered.
• Display on: In Display off mode, press any button to wake the screen.
• Compensation: When it is turned on and the menu is out of the state, short-press the power on/off button to complete the corresponding compensation action.

2. BRIGHTNESS BUTTON

• Adjust screen brightness: Short press the brightness button to switch to the screen brightness.
• Focus far (some models): Long press and hold it to focus far.
• Switch to scene mode (some models): Long press and hold it to switch to the scene mode.

3. COLOR PALETTES BUTTON

• Switch to color palettes: Short press it to switch to white hot/black hot, red hot/iron red, and blue hot.
• Menu: Long press and hold the color palettes button to enter the menu. When the menu is called up, short press the menu to confirm the current option and return to the previous menu. Long press and hold the menu to return or exit the menu without saving the current settings.

4. ZOOM-IN BUTTON

• Zoom-in: When the device is turned on and the menu is not called up, short press the button to switch to magnification and PIP.
• Focus near (some models): Long press and hold it to focus near.
• Hot track (some models): Long press and hold it to adjust the hot track.

Function Description

1. Video output: It can be turned on or off.
2. WiFi: The WiFi can be used to transmit real-time video to the mobile phone after the mobile phone client is connected to the device, and the device can be operated through the APP.
3. Laser cursor: Red, yellow and blue laser cursors can be switched on or off.
4. Image contrast (some models): Adjustable for 5 levels.

   NOTE: The adjusted contrast value will be saved in the current scene mode.

5. Image brightness (some models): Detector brightness can be adjusted with 5 levels.

   NOTE: The adjusted brightness value will be saved in the current scene mode.

6. Hot track: A white cross cursor is displayed when it is turned on to trace the highest temperature point in the full image.
7. Scene mode: Three scene modes, natural/enhanced/highlight, can be set.
8. Auto Stand-by: The Auto Stand-by time can be set to 5/10/15 min. If there is no operation within the set time, the sleep state will be entered.
9. Automatic power-off: The automatic power-off time can be set to 15/30/60 minutes. If there is no button operation at the set time, the power-off will be entered, and the power-off will be completed.
10. Bluetooth: It can be set, and after it is turned on, the device can be controlled by the Bluetooth remote controller.
11. Working indicator lamp: It can be turned on or off.

Troubleshooting

1. The device fails to start
   Solution: Replace the cell or connect the adapter for charging.
2. The screen goes out during use
   Solution: Short press any button to wake up sleep and light up the screen.
3. The image of the device is blurred during use
   Solution: Long press and hold the brightness button or Zoom-in button for focusing until the display is clear.

Storage and Transport

The following is the correct storage and transportation of the product. To prevent danger, property loss, etc., please read the manual carefully before using the device. Strictly observe it, and keep the instruction properly after reading it.

Storage:

1. The packaged product shall be stored in a well-ventilated, clean, condensate-free and corrosive gas-free room with temperature of -30 ℃ ~ 60 ℃ and relative humidity not exceeding 95%.
2. Please take it out and charge it once every 3 months.

Transport:

During transport, it shall be protected against rain, water flooding and falling, without severe vibration and impact. It shall be handled with care and throwing is strictly prohibited.