HIOKI LR8520 Wireless Fungal Logger Instruction Manual

Instruction Manual for HIOKI models including: LR8520 Wireless Fungal Logger, LR8520, Wireless Fungal Logger, Fungal Logger

WIRELESS FUNGAL LOGGER LR8520

File Info : application/pdf, 146 Pages, 9.21MB

LR8520B960-06

LR8520

Instruction Manual

WIRELESS FUNGAL LOGGER

Be sure to read this manual before using the instrument.

Safety Notes

p.4

When using for the first time

Fungal Index

p.16

Collecting Measurement Data Using a Windows® PC
Collecting Measurement Data Using an AndroidTM Terminal

p.31 p.83

Troubleshooting Maintenance and Service p.125

Troubleshooting

p.127

Error Display

p.130

Dec. 2020 Revised edition 6 LR8520B960-06 20-12H
HIOKI LR8520B960-06

HIOKI LR8520B960-06

Contents

Introduction........................................................................................1 Trademark ..........................................................................................1 Verifying Package Contents .............................................................2
Options ................................................................................................. 3 Safety Notes.......................................................................................4 Usage Notes.......................................................................................7

1 Overview

1.1 Overview and Features..........................................................15 1.2 Fungal Index ...........................................................................16 1.3 Parts Names and Functions..................................................17 1.4 Display Configuration............................................................19

2 Preparation for Measurements

2.1 Inspection Before Use ...........................................................21
2.2 Inserting/Replacing Batteries ...............................................22 Installation (Replacement).................................................................. 23 Battery indicator display ..................................................................... 24 Battery life indication .......................................................................... 24
2.3 Connecting the AC Adapter...................................................25 External Power Supply ....................................................................... 25
2.4 Installing the Strap (optional) ...............................................26
2.5 Connecting Cables.................................................................27 Connecting the temperature and humidity sensor.............................. 27 Connecting the alarm output cable..................................................... 28

3 Collecting Measurement Data Using a

Windows® PC

LR8520B960-06

HIOKI LR8520B960-06

Contents

3.1 Software Specifications.........................................................31 System requirements ......................................................................... 31 Function specifications ....................................................................... 32
3.2 Measurement Workflow .........................................................33 3.3 Installing the Software...........................................................35
Installation .......................................................................................... 35 Startup procedure............................................................................... 36 Termination procedure........................................................................ 36 Uninstallation...................................................................................... 37
3.4 Display Configuration............................................................38 3.5 Basic Operation Procedure...................................................39
Operation flow .................................................................................... 39 Selecting multiple wireless loggers .................................................... 40
3.6 Registering/Deleting a Wireless Logger ..............................41 Registering a wireless logger ............................................................. 41 Deleting a wireless logger .................................................................. 44 Grouping wireless loggers.................................................................. 45
3.7 Setting Measurement Conditions ......................................... 47 Setting measurement ......................................................................... 48 Setting the channel............................................................................. 50 Setting scaling (as needed)................................................................ 52 Setting the alarm function (as needed) .............................................. 55 Setting the power saving function (as needed) .................................. 58 Setting the environment ..................................................................... 59 Communications................................................................................. 61 Copying the settings........................................................................... 63 Initializing the settings ........................................................................ 64
3.8 Sending/Receiving the Setting Conditions..........................65 Sending the settings........................................................................... 65 Receiving the settings ........................................................................ 66
3.9 Starting and Stopping Measurement and Monitoring ........67 Starting and stopping measurement .................................................. 67 Starting and stopping status monitoring ............................................. 68 Starting and stopping value monitoring .............................................. 69
3.10 Collecting Measurement Data...............................................70

HIOKI LR8520B960-06

Contents

Starting and stopping data collection ................................................. 70
3.11 Browsing/Analyzing Measurement Data..............................71 Browsing measurement data.............................................................. 71 Exporting measurement data ............................................................. 72 Deleting measurement data ............................................................... 74
3.12 Performing Wireless Logger Maintenance ..........................75 Setting the clock ................................................................................. 75 Self-diagnosis..................................................................................... 76 Checking the version number............................................................. 77 Updating the firmware version............................................................ 78
3.13 Convenient Functions ...........................................................79

4 Collecting Measurement Data Using an

AndroidTM Terminal

4.1 Software Specifications.........................................................83 System requirements ......................................................................... 83 Function specifications ....................................................................... 83
4.2 Measurement Workflow .........................................................84 4.3 Installing the Software...........................................................87
Installation .......................................................................................... 87 Startup procedure............................................................................... 88 Uninstallation...................................................................................... 88
4.4 Display Configuration............................................................89 4.5 Registering/Deleting a Wireless Logger ..............................94
Registering a wireless logger ............................................................. 94 Deleting a wireless logger .................................................................. 95 Grouping wireless loggers.................................................................. 96
4.6 Setting Measurement Conditions ......................................... 98 Setting measurement ......................................................................... 99 Setting the channel........................................................................... 100 Advance settings .............................................................................. 101 Initializing the setting ........................................................................ 102
4.7 Sending/Receiving the Setting Conditions........................103 Sending the settings......................................................................... 103

HIOKI LR8520B960-06

iii

Contents

Receiving the settings ...................................................................... 104
4.8 Starting and Stopping Measurement and Monitoring ......105 Starting and stopping measurement ................................................ 105 Starting and stopping monitoring...................................................... 106
4.9 Collecting Measurement Data.............................................108 Starting and stopping data collection ............................................... 108
4.10 Browsing/Analyzing Measurement Data............................109 Browsing measurement data............................................................ 109 Exporting measurement data ........................................................... 111 Deleting measurement data ............................................................. 114
4.11 Performing Wireless Logger Maintenance ........................ 115 Setting the clock ............................................................................... 116 Checking the version number........................................................... 116

5 Specifications

117

5.1 LR8520 Wireless Fungal Logger......................................... 117 5.2 Z2010, Z2011 Humidity Sensor ...........................................122

6 Maintenance and Service

125

6.1 Repair, Inspection, and Cleaning........................................125 6.2 Troubleshooting ...................................................................127 6.3 Error Display.........................................................................130 6.4 Disposal ................................................................................131
Removing lithium batteries ............................................................... 131

Appendix

Appx.1

Recording interval and recording time.........................................Appx.1 Target collection time...................................................................Appx.1 Initial setting list ...........................................................................Appx.2 Handling Data..............................................................................Appx.2 For customers who are using the LR8410 Wireless Logging
Station .........................................................................................Appx.3 Using the LR8410 as a Unit ........................................................Appx.4

HIOKI LR8520B960-06

Introduction

Thank you for purchasing the HIOKI LR8520 Wireless Fungal Logger. To obtain maximum performance from the product, please read this manual first, and keep it handy for future reference.

There are the following instruction manuals available for this instrument. Please refer to the appropriate manuals for the intended usage.

Model

Manual contents

Measurement Guide
Instruction Manual (this manual) Precautions Concerning Use of Equipment That Emits Radio Waves Logger Utility* User Manual

For customers who use this instrument for the first time, this manual describes the basic operation procedures.
Describes details of the functions, operations, and specifications of this instrument.
Precautions relating to use of equipment that emits radio waves, countries in which the instrument has been certified, etc.
Describes how to operate the PC application software.

Printed CD edition edition

*: To install the PC application software, Logger Utility, see "3.3 Installing the Software" (p.35). For information about its operating procedure, see the Logger Utility User Manual contained in the accompanying CD-R.

Trademark

· Microsoft, Windows, and Microsoft Excel are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.
· The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Hioki E.E. Corporation is under license. Other trademarks and trade names are those of their respective owners.
· Adobe and Adobe Reader are either trademarks or registered trademarks of Adobe Systems Incorporated in the United States and other countries.
· Android and Google Play are trademarks of Google, Inc.

HIOKI LR8520B960-06

Verifying Package Contents

· When you receive the instrument, inspect it carefully to ensure that no damage occurred during shipping. In particular, check the accessories, panel keys, and connectors. If damage is evident, or if it fails to operate according to the specifications, contact your authorized Hioki distributor or reseller.
Check the package contents as follows.

Instrument

Accessories

LR8520 × 1

Logger Application Disc (CD-R)*
· Instruction Manual (PDF) · Logger Utility · Wireless Logger Collector · Logger Utility Instruction Manual (PDF)
*: The latest version of the application software can be downloaded from our website.

Measurement Guide

Precautions Concerning Use of Equipment That Emits Radio Waves

LR6 Alkaline battery × 2 L1010 Connection Cable (length approx. 1.5 m) × 1

HIOKI LR8520B960-06

Verifying Package Contents
Options
The options listed below are available for the instrument. To order an option, please contact your authorized Hioki distributor or reseller. Options are subject to change. Please check Hioki's website for the latest information. Z2010 Humidity Sensor
(Length including the sensor: Approx. 50 mm) Z2011 Humidity Sensor (Cable length: Approx. 1.5 m) Z2003 AC Adapter (power cord attached)
Z5004 Magnetic Strap Z5020 Magnetic Strap
L1010 Connection Cable (length approx. 1.5 m)
Supported instrument LR8410 Wireless Logging Station

HIOKI LR8520B960-06

Safety Notes

This instrument is designed to conform to IEC 61010 Safety Standards, and has been thoroughly tested for safety prior to shipment. However, using the instrument in a way not described in this manual may negate the provided safety features. Before using the instrument, be certain to carefully read the following safety notes.
DANGER
Mishandling during use could result in injury or death, as well as damage to the instrument. Be certain that you understand the instructions and precautions in the manual before use.

WARNING
If you do not have knowledge or experience of electrical measurements, use this instrument under supervision of experienced personnel.

Notation In this manual, the risk seriousness and the hazard levels are classified as follows.

DANGER WARNING CAUTION
IMPORTANT

Indicates an imminently hazardous situation that will result in death or serious injury to the operator.
Indicates a potentially hazardous situation that may result in death or serious injury to the operator.
Indicates a potentially hazardous situation that may result in minor or moderate injury to the operator or damage to the instrument or malfunction.
Indicates information related to the operation of the instrument or maintenance tasks with which the operators must be fully familiar.
Indicates a strong magnetic-field hazard. The effects of the magnetic force can cause abnormal operation of heart pacemakers and/or medical electronics.

Indicates prohibited actions.

Windows Dialog [ ]
4

Indicates an action that must be performed.
Additional information is presented below. Windows 7, Windows 8, and Windows 10 are referred to as Windows, otherwise specified. Windows dialog boxes are referred to as dialogs. The names and keys on the screen including menus, commands, dialogs, dialog button names, etc. are enclosed in brackets [ ].
HIOKI LR8520B960-06

Safety Notes

Symbols affixed to the instrument
Indicates cautions and hazards. When the symbol is printed on the instrument, refer to a corresponding topic in the Instruction Manual.
Indicates a grounding terminal.
Indicates DC (Direct Current).

Symbols for various standards

Indicates the Waste Electrical and Electronic Equipment Directive (WEEE Directive) in EU member states.

Indicates that the instrument conforms to regulations set out by the EU Directive.

Indicates that the product incorporates Bluetooth® wireless technology.

FCC ID

Indicates the ID number of the wireless module certified by the U.S. Federal Communications Commission (FCC).

Indicates the identification number of a wireless module approved by Industry Canada (IC).

Screen display The instrument screen displays the alphanumeric characters as follows.
A B CD E F GH I J K L MNOPQR S T U VWX Y Z

12 3 4 56 7 890

HIOKI LR8520B960-06

Safety Notes

Accuracy
We define measurement tolerances in terms of rdg. (reading) and dgt. (digit) values, with the following meanings:

(Maximum display value or scale length/range)

f.s.

The maximum displayable value or scale length. This is usually the name of

the currently selected range.

(Reading or displayed value)

rdg.

The value currently being measured and indicated on the measuring

instrument.

(Resolution)

dgt.

The smallest displayable unit on a digital measuring instrument, i.e., the input

value that causes the digital display to show a "1" as the least-significant digit.

Measurement categories
To ensure safe operation of measuring instruments, IEC 61010 establishes safety standards for various electrical environments, categorized as CAT II to CAT IV, and called measurement categories.

DANGER
· Using a measuring instrument in an environment designated with a higher-numbered category than that for which the instrument is rated could result in a severe accident, and must be carefully avoided.
· Using a measuring instrument without categories in an environment designated with the CAT II to CAT IV category could result in a severe accident, and must be carefully avoided.

CAT II: CAT III: CAT IV:

When directly measuring the electrical outlet receptacles of the primary electrical circuits in equipment connected to an AC electrical outlet by a power cord (portable tools, household appliances, etc.) When measuring the primary electrical circuits of heavy equipment (fixed installations) connected directly to the distribution panel, and feeders from the distribution panel to outlets When measuring the circuit from the service drop to the service entrance, and to the power meter and primary overcurrent protection device (distribution panel)

Distribution panel Service entrance
Service drop
CAT IV Power meter

Internal wiring CAT II
CAT III

Outlet

Fixed installation

HIOKI LR8520B960-06

Usage Notes
Usage Notes
Follow these precautions to ensure safe operation and to obtain the full benefits of the various functions.
Bluetooth® This instrument, the LR8410 uses radio waves of a band frequency of 2.4 GHz. No radio station license is required to use this product, however, be aware of the following.
WARNING
· Do not use this instrument in a system that requires high safety and reliability.
· Do not use this instrument near any medical equipment, such as a pacemaker, etc.
· Do not modify, disassemble, or repair the instrument.
CAUTION
· If this instrument is used near any equipment that uses the same frequency band, such as wireless LAN equipment, etc., communications may become unstable or other equipment may be affected.
· The line-of-sight distance between the instrument and the LR8410 is 30 m. If there is an obstacle (wall, metal screen, etc.), communications may become unstable or the communications distance may become shorter. In addition, even if multiple instruments are installed in the same environment, each instrument may show a different radio-field strength (antenna-like indication).
· Communications between the instrument and the LR8410 are encrypted by SSP, however, the confidentiality of any information is not guaranteed. We are not responsible for any leakage of measurement data by wireless communications.
· This instrument, the LR8410 generates electric waves. Usage of electric waves requires permission and authorization in each country. Using electric waves in any country or region other than the ones listed in the attached document "Precautions Concerning Use of Equipment That Emits Radio Waves" is against the law and may be subject to punishment.
When the instrument is positioned on a stand instead of directly on the floor, communications can become more stable.

HIOKI LR8520B960-06

Usage Notes

Check before use Verify that it operates normally to ensure that no damage occurred during storage or shipping. If you find any damage, contact your authorized Hioki distributor or reseller.
Installation
WARNING
Installing the instrument in inappropriate locations may cause a malfunction of the instrument or may give rise to an accident. Avoid the following locations. · Exposed to direct sunlight or high temperature · Exposed to corrosive or combustible gases · Exposed to water, oil, chemicals, or solvents · Exposed to high humidity or condensation · Exposed to a strong electromagnetic field or electrostatic charge · Exposed to high quantities of dust particles · Near induction heating systems (such as high-frequency induction
heating systems and IH cooking equipment) · Susceptible to vibration For details on the operating temperature and humidity, see the specifications.
CAUTION
· This instrument is not drip-proof. Water that drips on the connector could cause a malfunction.
· Do not allow any condensation to form. Condensation can form particularly in an environment where the temperature changes drastically.
· Do not allow the instrument to become wet or take measurements with wet hands. Doing so may cause a malfunction.
· Do not position the instrument on an unstable table or inclined surface. When the instrument falls or tips, an injury or malfunction can occur.
Handling of this instrument
CAUTION
Avoid any vibration or impact to prevent damage to the instrument during transportation and handling. Be especially careful regarding the impact by a fall.

This instrument may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.

HIOKI LR8520B960-06

Usage Notes
Handling of cords and cables
WARNING
Make sure to use the specified power cord when using the instrument. Otherwise, a fire may be caused.
CAUTION
· Avoid stepping on or pinching the cables to prevent damage to the cables. Do not bend or pull the cables.
· To prevent any wires from breaking, pull on the connector end, not the cable, to disconnect the output connector.
· To prevent any wires from breaking, pull on the connector end, not the cord, to disconnect the power cord from the outlet or the instrument.
· The cables become stiff below 0°C. If the cables are bent or pulled in this condition, the cable insulation may be damaged or the wires may be cut.
· Observe the following precautions when making a connection to the alarm output terminal to prevent damage to the instrument. (1) Turn off the power to the instrument to be connected before making a connection. (2) Do not make any connection that exceeds the rating of the alarm output terminal. Maximum rating: 30 V DC, 200 mA
Position the sensor cable away from the power line or ground cable.
Before turning on the power
CAUTION
· When operating the instrument using a UPS (uninterruptible power supply) or DC-AC inverter, do not use any square-wave and pseudo sinewave UPS or DC-AC inverter. Doing so may damage the instrument.
· Make sure that the power voltage connection is correct. Connection errors could damage the internal circuit.

The instrument and measurement unit will not fail due to a momentary power failure under 40 ms. If the power failure is longer than 40 ms, the power may be shut off temporarily. Install the instrument in consideration of power conditions at the installation location.

HIOKI LR8520B960-06

Usage Notes
Magnet of the optional strap
DANGER
Those with medical electronics such as pacemakers should not use the Z5004/Z5020 Magnetic Strap. Nor should such persons approach the Z5004/Z5020. It is extremely dangerous. The electronics may not operate properly and the life of the operator may be put at great risk.
WARNING
Swallowing magnets could be life-threatening. Keep any magnets out of reach, especially of small children. If you accidentally swallow magnets, immediately seek medical attention.
CAUTION
· Do not use the Z5004/Z5020 in locations where it may be exposed to rainwater, dust, or condensation. In those conditions, the magnet may be decomposed or deteriorated. The magnet adhesion may be diminished. In such case, the instrument may not be hung in place and may fall.
· Do not bring the Z5004/Z5020 near magnetic media such as floppy disks, magnetic cards, pre-paid cards, or magnetized tickets. Doing so may corrupt and may render them unusable. Furthermore, if the Z5004/Z5020 is brought near precision electronic equipment such as PCs, TV screens, or electronic wrist watches, they may fail.
· Keep magnets away from any impact by a fall. The magnets may chip or crack due to impact.

HIOKI LR8520B960-06

Usage Notes
AC adapter
WARNING
· Make sure to use the optional Z2003 AC Adapter. The rated power voltage for the AC adapter is 100 V to 240 V AC and the rated power frequency is 50 Hz/60 Hz. Do not use the AC adapter at any voltage other than the above to avoid damage to the instrument and electrical accidents.
· Before turning on the power, make sure that the power voltage indicated on the AC adapter matches the power voltage to be used. Using the AC adapter outside the specified power voltage range could cause damage to the instrument or AC adapter or electrical accidents.
CAUTION
· Connect the output plug to the instrument and then connect the plug to an outlet. Connecting the energized output plug to the instrument may damage the instrument.
· When connecting an external power supply, connect the output plug to the instrument and then supply external power.
Handling of batteries
WARNING
· Do not short circuit, disassemble, or incinerate batteries. Do not charge alkaline batteries. Doing so may cause an explosion. Handle and dispose of batteries in accordance with local regulations.
· In order to prevent electric shocks, remove measurement cables and then replace the batteries.
· After battery replacement, reattach and screw down the battery cover before use.
· To prevent damage to the instrument or electric shocks, make sure to use the battery cover screw (screw with a spring) that is attached at the time of shipment. If you lose the screw or spring or find any damage, contact your authorized Hioki distributor or reseller.

HIOKI LR8520B960-06

Usage Notes
CAUTION
Poor performance or damage from battery leakage could result. Observe the cautions listed below. · Do not mix new and old batteries, or different types of batteries. · Be careful to observe the battery polarity during installation. Poor
performance or damage from battery leakage could result. · Do not use batteries after their recommended expiry date. · Do not allow used batteries to remain in the instrument. · To avoid corrosion from battery leakage and/or damage to the instrument,
remove the batteries from the instrument if it is to be kept in storage for an extended period.
IMPORTANT The displayed remaining battery level may be different from the actual remaining battery level due to the battery characteristics, settings during use, temperature or consumption level. When a battery is used in a low temperature environment or a weak and deteriorated battery is used, the power may shut off regardless of the battery indicator display.
Batteries The battery indicator display and battery life are based on the use of a new alkaline battery.
Use of nickel-metal hydride batteries When nickel-metal hydride batteries are used, the battery indicator display does not operate correctly. The battery life varies depending on the capacity, charging condition, deterioration due to repeated use, etc. Use batteries in consideration of the factors above.
Use of manganese dioxide batteries Do not use manganese dioxide batteries as the instrument may not be able to measure or communicate.

HIOKI LR8520B960-06

Usage Notes
Wire connection
DANGER
Do not permanently connect the instrument in an environment where there is a possibility of surges exceeding the dielectric withstand voltage. Doing so may damage the instrument and result in personal injury.
WARNING
Do not connect any equipment other than the specified temperature and humidity sensor to the instrument. Doing so may cause electric shocks or damage to the instrument. The power supply ground and alarm output terminal (ground) are common and not isolated. When using an external power supply, use an isolated external power supply or connect the wires so that there is no potential difference between the ground of the external power supply and the object for which an alarm is to be output to prevent damage to the instrument or electric shocks.
Handling of CD
· Do not allow any dirt or scratches on the disk recording surface. When writing on the label face, use a pen with a soft tip.
· Store the disk in a protective case and do not expose the disk to direct sunlight or high temperatures and humidity.
· We are not responsible for any trouble in the Windows® computer system when this disk is used.

HIOKI LR8520B960-06

Usage Notes
Handling of temperature and humidity sensor
CAUTION
· The temperature and humidity sensor is not dustproof or waterproof. Do not use the sensor in locations where it may be exposed to dust or water. It may cause a malfunction of the instrument.
· The temperature and humidity sensor is not drip-proof. Water that drips onto the connector could cause a malfunction.
· Sensor sensitivity and precision will degrade over time, even under normal operating conditions. To maintain the instrument's ability to make measurements that conform to the accuracy specifications, it is recommended to replace the temperature and humidity sensor with a new unit once it has been used for one year after being opened.
· When the sensor is used outside the specified operating (storage) environment, the sensor accuracy may deteriorate even within the 1 year accuracy warranty period and accurate measurement cannot be performed.
· In principle, the surface of the instrument's temperature and humidity sensor may become contaminated if exposed to an environment containing organic gases (ketone, acetone, ethanol, toluene, etc.), increasing the error component of humidity measurement.
· Do not expose the temperature and humidity sensor to any concentrated chemical solvent for an extended period of time while it is used or stored.
· The sensor may become contaminated by organic gases released from some types of vinyl chloride and packaging material.
· When the temperature and humidity sensor is not used, place it with a drying agent in a plastic bag, seal the bag completely, and store it in a cool, dark place.
· Do not allow any condensation to form. Condensation can form particularly in any environment where the temperature changes drastically.
· This instrument does not come with a guarantee against any problem when the sensor is used outside the specified operating (storage) environment.
· Due to a humidity change (from low to high humidity or high to low humidity), up to ±1% RH of change (hysteresis) occurs in the measured humidity value.
Precautions during shipment
CAUTION
· To avoid damaging the instrument, remove accessories and options from the instrument.
· Avoid any vibration or impact to prevent damage to the instrument and humidity sensor during transportation and handling. Be careful especially with impact by a fall.

HIOKI LR8520B960-06

1 Overview
1.1 Overview and Features
Possible fungal growth at a glance A fungal index enables you to predict a time period before fungal growth starts.
Easy operation You can start recording immediately by pressing the REC/STOP key as soon as the instrument is installed. Data is collected and managed as a batch by the terminal. Analyze the data using the software provided with the instrument.
LR8520

Android tablet

Android smartphone

Mass memory installed

The memory capacity per channel is 500,000 data units.

Windows® PC

3-way power supply
You can choose a power supply from LR6 alkaline batteries, AC adapter, and external power supply (5 V to 13.5 V).

Compatible with HIOKI LR8410
When the instrument is used as a unit for the LR8410, data can be collected in real time. For the connection procedure, see the instruction manual for each instrument.

LR8520

LR8410

Windows® PC

LAN/USB communications

HIOKI LR8520B960-06

Fungal Index

1.2 Fungal Index

A fungal index is an indicator to help predict how fungi are likely to grow. Fungal growth correlates with temperature and relative humidity and a fungal index can be calculated from temperature and relative humidity. It is mainly used to quantitatively indicate the climate of fungal growth indoors as a numerical value (Japanese Patent Number 2710903). The instrument calculates a fungal index between 0 and 200 from temperature and humidity using a highly accurate temperature and humidity sensor.

Temperature [°C]

40 40
20 7 30
20

80 160

100

Relative humidity [% RH]

Fungal index

Time period before Time period before

fungal growth starts fungal contamination

(estimate)

starts (estimate)

Example of indoor living environment

2 months

10 years or more · Dry area

1 month

2 weeks

5 days

8 years 3 years 2 years

· Living space · Closet · Shoe cabinet

3 days

1 day

100

12 hours

200

6 hours

1 year 4 months 2 months 1 month

· Underfloor · Bathroom · Inside air-conditioner during
cooling operation

Fungal contamination starts even more quickly in an environment where the contamination is already progressing or fungi are fed and nourished.

Predicted fungal growth
Fungal growth is predicted at 5 levels (measurement value: 0 to 4) from the accumulated fungal index. The following symbols appear in the display of the instrument.

(No symbol)

No new spores are growing.
Measurement value: 0

A hypha starts extending.
Measurement value: 1

New spores are growing.
Measurement value: 2

Spores start spreading.
Measurement value: 3

A lot of spores are spreading (the spore part in the display blink).
Measurement value: 4

A fungal index is a highly reliable indicator based on academic research, however, it does not guarantee that fungal growth is completely controlled in any environment with a low fungal index.

HIOKI LR8520B960-06

Parts Names and Functions

1.3 Parts Names and Functions

Front

Rear

(Common areas of each model are described.)

Display

Battery cover (p.22)

1 23
Operation keys
1 Power 2 Display 3 Measurement

Press briefly

Hold down (for at least 2 seconds)

Bluetooth ON/OFF
Display change YES (During operation
verification) NO (During operation
verification)

Power ON/OFF
Measurement start/stop

Left side

Right side
Serial number label The serial number consists of 9 digits. The first two (from the left) indicate the year of manufacture, and the next two indicate the month of manufacture. It is necessary for production control requirements such as the product warranty. Do not peel off the label.
AC adapter connection terminal
(p.25)

Sensor connection terminal Alarm output terminal
(p.27)

HIOKI LR8520B960-06

Parts Names and Functions

Display

Description

Channel (CH)

Blinking: During monitoring

MAX Maximum value MIN Minimum value AVG Average value

Data number

Unit number (1 to 7)

Date and time

Operation verification

Measurement

Lit: Performing measurement

Blinking: Waiting for a

measurement start to be

preset

Alarm
Lit: The current measurement value is outside the range. Blinking: There was a value
that was outside the range
but the current value is in the
range. (Alarm hold)

Display
2

Description Fungal index display

Predicted fungal growth display

AVG Average recording mode MODE (Not used for this instrument)

Lit: Bluetooth ON

Blinking: Bluetooth OFF

(The power saving function is

enabled.)

Off: Bluetooth OFF

Bluetooth connection status (3 levels) (Signal strength 1: Weak to 3: Strong) Blinking: Security lock Off: Bluetooth not connected

Operating with the AC adapter

Battery indicator display (p.24)

Displays the unit of

measurement values.

· While the Bluetooth is being connected (the antenna symbol ( ) is lit), it cannot be turned off.
· The power cannot be turned off during measurement. · During real-time measurement using the LR8410 Wireless Logging Station, the
measurement cannot be stopped with key operation on the instrument.

HIOKI LR8520B960-06

1.4 Display Configuration

Display Configuration

Fungal index*1, *2, *5

Temperature and humidity measurement value*1, *2, *5

Time*4

Fungal index statistic (maximum and minimum)*1, *2, *5

Screen change

Fungal index statistic (average value)*1, *2, *5

Date*4

Temperature and humidity statistic (maximum)*1, *2, *5

Unit number (1 to 7)*3

Temperature and humidity statistic (minimum)*1, *2, *5

Number of measurement data*1, *6

Temperature and humidity statistic (average)*1, *2, *5

HIOKI LR8520B960-06

Display Configuration

*1 Update for each sample during measurement.
*2 The unit of the channel for which the scaling setting is ON is not displayed. If it matches the
unit for which a segment is prepared, however, the unit is displayed. *3 It is displayed only when connected to the LR8410 . *4 The current time is set from the wireless logger collector. (p.75) It can also be set from
the LR8410 . For more details, refer to the LR8410 instruction manual. *5 When scaling is set to ON, the allowable display range is indicated in the following table.

Scaling displayed digit setting

U.F display (Underflow)

Automatic -10,000 or less

0 digit -10,000 or less

1 digit -1,000.0 or less

2 digits -100.00 or less

3 digits -10.000 or less

Allowable display range

O.F. display (Overflow)

±0.001 to ±9,999 ±1 to ±9,999 ±0.1 to ±999.9 ±0.01 to ±99.99 ±0.001 to ±9.999

+10,000 or more +10,000 or more +1,000.0 or more +100.00 or more +10.000 or more

0 display (Zero)
Less than ±0.001 Less than ±1 Less than ±0.1 Less than ±0.01 Less than ±0.001

*6 If the value is 10,000 or more, it is displayed at the top and bottom.

HIOKI LR8520B960-06

2 Preparation for Measurements

Before using the instrument, make sure to refer to "Usage Notes" (p.7).

2.1 Inspection Before Use

Before using the instrument for the first time, verify that it operates normally to ensure that no damage occurred during storage or shipping. If you find any damage, contact your authorized Hioki distributor or reseller.
"Before sending the instrument for repair" (p.127)

Checking the instrument appearance and operation

Check item

Action

Is there any damage to the

If it is damaged, there is a risk of electric shocks. Do not

instrument and connection cable? use the instrument but instead send it for repair.

Does the display turn on when the power is turned on/batteries are inserted?

If the display does not turn on, send the instrument for repair.

Does the battery indicator

display

When

is displayed, replace the current batteries with

new batteries.

Is the temperature and humidity value displayed?

If the temperature and humidity values are not displayed, completely insert the Z2010 or Z2011 Temperature and Humidity Sensor.

HIOKI LR8520B960-06

Inserting/Replacing Batteries
2.2 Inserting/Replacing Batteries
Insert two LR6 Alkaline batteries. Before measurements, check that the battery level is sufficient. When the battery charge is low, replace the batteries.
CAUTION
Stop measurement and then replace the batteries. Replacing the batteries during measurement may damage the data.
IMPORTANT Batteries The battery indicator display and battery life are based on the use of a new alkaline battery.
Use of nickel-metal hydride batteries When nickel-metal hydride batteries are used, the battery indicator display does not operate correctly. The battery life varies depending on the capacity, charging condition, deterioration due to repeated use, etc. Use batteries in consideration of the factors above.
Use of manganese dioxide batteries Do not use manganese dioxide batteries as the instrument may not be able to measure or communicate.
· Even when the batteries are low in charge or replaced, the data and measurement conditions saved in the instrument are not deleted.
· When the battery voltage drops to the point where the instrument cannot operate properly, the screen on the right is displayed. Measurement or communications cannot be made in this condition. When the Z2003 AC Adapter is connected or the batteries are replaced, the instrument returns to the normal operation.

HIOKI LR8520B960-06

Inserting/Replacing Batteries

Installation (Replacement)

WARNING
To prevent damage to the instrument or electric shocks, make sure to use the battery cover screw (screw with a spring) that is attached at the time of shipment. If you lose the screw or spring or find any damage, contact your authorized Hioki distributor or reseller.

Required items LR6 Alkaline battery × 2, Phillips screwdriver (No. 2)
1 Remove the connection cables.

2 Using a Phillips screwdriver, remove the screw (1 location) from the battery cover.

3 6
5

The screw cannot be removed from the battery cover. Do not try to remove the screw forcefully.

2, 7

3 Slide up and remove the cover.

4 4

Remove the old batteries (for battery

replacement).

5 Insert new batteries, being careful with the battery polarity.

6 Slide down and reattach the battery cover.

7 Secure the cover with the screw.

HIOKI LR8520B960-06

Inserting/Replacing Batteries When batteries are installed, the following screen is displayed.

All indicators on

Model

Version number

Battery indicator display

Displayed at the upper right corner of the display.

Fully charged.

As the battery charge diminishes, black charge bars disappear, one by one, from the left of the battery indicator.

The battery voltage is low. Replace the batteries as soon as possible.

(Blinks) The battery is drained. Recording or communications cannot be made in this condition.

Off

The battery indicator display turns off when the AC adapter or an external power supply is connected.

IMPORTANT
The displayed remaining battery level may be different from the actual remaining battery level due to the battery characteristics, settings during use, temperature or consumption level. When a battery is used in a low temperature environment or a weak and deteriorated battery is used, the power may shut off regardless of the battery indicator display.

Battery life indication

The battery life varies depending on the recording interval.

0.5 sec.

Recording interval

1 sec.

10 sec.

1 min.

Real-time measurement Bluetooth ON

Approx. 5 days

Approx. 7 days Approx. 10 days Approx. 14 days

Manual data collection Bluetooth ON

Approx. 20 days Approx. 20 days Approx. 20 days Approx. 20 days

Manual data collection Bluetooth OFF

Approx. 2.5 months

Approx. 3 months

Approx. 3.5 months

HIOKI LR8520B960-06

Connecting the AC Adapter

2.3 Connecting the AC Adapter

Connect the instrument, the optional Z2003 AC Adapter, and power cord, and then connect to an outlet. When using the AC Adapter with a batteries, the AC Adapter has priority in powering the instrument. When power from the AC Adapter is interrupted, the instrument or module will switch to battery power. Before connecting, make sure to read "AC adapter" (p.11) and "Handling of cords and cables" (p.9).

Rated supply voltage: 100 V to 240 V AC Rated supply frequency: 50 Hz/60 Hz

1 Connect the power
cord and AC adapter.

3
AC adapter
1
Power cord

2 Connect the outlet
plug to the instrument AC adapter connection terminal (left side).
2
3 Connect the output
plug to an outlet.

When the AC adapter is connected, the following screen is displayed.

All indicators on When the AC adapter is used,

Model

Version number

is lit at the upper right of the display.

External Power Supply
The instrument can work either on a DC power supply unit (5 V to 13.5 V DC) or the USB bus power (5 V DC). If you need a conversion cord to connect the instrument and an external power supply unit, contact your authorized Hioki distributor or retailer.

HIOKI LR8520B960-06

Installing the Strap (optional)
2.4 Installing the Strap (optional)
When the optional Z5004/Z5020 Magnetic Strap is attached to the instrument, the magnet can be attached to the wall surface (metal plate).
1 Attach the Z5004 or Z5020 through the strap hole.
In order of (1) (2) (3)
(1)

(2) (3)

Magnet

2 Attach it to the wall surface (with a metal plate affixed).

HIOKI LR8520B960-06

Connecting Cables

2.5 Connecting Cables

Connecting the temperature and humidity sensor
Attach the Humidity Sensor to the sensor connection terminals of the instrument.
Supported sensors Z2010 Humidity Sensor Length including the sensor: Approx. 50 mm Z2011 Humidity Sensor Cable length: Approx. 1.5 m

Right side of instrument

Z2010 or Z2011 Humidity Sensor

Completely insert the Humidity Sensor.

· When the temperature and humidity sensor is not completely inserted, [BURN OUT] is displayed for the measurement value and [BURN] is displayed on the screen.
· If a correct value is not displayed even when the sensor is completely inserted, the instrument or the sensor may have a problem. Send the instrument for repair.

HIOKI LR8520B960-06

Connecting Cables

Connecting the alarm output cable

Connect the alarm output cable (L1010 Connection Cable) to the alarm output terminal of the instrument.

Right side of instrument

Not
- used +

Alarm output cable (L1010 Connection Cable) (length approx. 1.5 m)
Red wire: Alarm output signal + - Black wire: GND
WARNING
The power supply ground and alarm output terminal (ground) are common and not isolated. When using an external power supply, use an isolated external power supply or connect the wires so that there is no potential difference between the ground of the external power supply and the object for which an alarm is to be output to prevent damage to the instrument or electric shocks.
· If a wrong input on the instrument side or the connection destination is made or the alarm output cable is not completely inserted, the instrument does not operate properly.
· If the instrument does not operate properly even when the alarm output cable is completely inserted, the instrument or connection cable may have a problem. Send the instrument for repair.

HIOKI LR8520B960-06

Connecting Cables

Alarm output circuit diagram
Open drain output (Maximum rating: 30 V DC, 200 mA) A switch (FET) is installed between the alarm output terminal and ground and turns ON (short circuit) when the signal is active (during alarm output).

Example of connection with an alarm signal light, buzzer, etc.

External power supply (12 V DC)

Instrument (LR8520)

Protective diode

Alarm signal light, Control terminal buzzer, etc.
+

Alarm output (Alarm output

terminal

signal)

- External relay

(GND)

HIOKI LR8520B960-06

Connecting Cables

HIOKI LR8520B960-06

Collecting Measurement Data Using a Windows® PC

Windows® PC

(Line-of-sight 30 m)

· Wireless Logger Collector · Logger Utility

3.1 Software Specifications
System requirements

CPU Memory Display
Hard disk OS
Communication method

1 GHz or faster 32-bit or 64-bit processor
1 GB or more of RAM (32-bit) or 2 GB or more of RAM (64-bit)
1,024 × 768 dots or more, 65,536 colors or more (Recommended: Use a small font. When a large font is used, the display may be disturbed.)
3.0 GB or more of available space
Windows 10 (32-bit/64-bit), Windows 8 (32-bit/64-bit), Windows 7 (32-bit/64-bit)
Bluetooth 2.1+EDR or higher Profile: SPP (Recommended: Use the Windows® standard protocol stack.)

HIOKI LR8520B960-06

Software Specifications

Function specifications

Number of allowable registrations Settings Measurement control Monitoring function
Measurement data collection function Analysis/browsing Measurement data output
Other

100 units
Measurement settings can be edited/copyed/initialized and sent/received.
Measurement can be started and stopped.
The status can be monitored. The status can be monitored repeatedly and periodically (10 minutes to 1 day).
Numerical values can be monitored. Update interval: 1 second
Measurement data can be collected. Measurement data can be collected repeatedly and periodically (10 minutes to 1 day).
Measurement data can be displayed in the waveform format and analyzed using the Logger Utility.
Measurement data can be output to a file in the following formats. Logger Utility format, LR5000 format, Smart Site compatibility format, CSV format, and text format
Measurement data can be combined. Measurement data obtained with several instruments can be combined to output as one file (in Logger Utility general-purpose data format).
Clock setting, self-diagnosis, version number check, and firmware version update

HIOKI LR8520B960-06

Measurement Workflow
3.2 Measurement Workflow 1 Install the instrument referring to "Preparation for Measurements"
(p.21).
2 Install the software on the Windows® PC. (p.35)
· Wireless Logger Collector · Logger Utility
3 Register the instrument in Wireless Logger Collector (up to 100 units).
(p.41)

When no wireless logger is found · When the symbol in the screen is off, press the power key to turn ON the Bluetooth
function. · When the symbol in the screen is off, a wireless connection is not established. Place the
instrument closer to the PC or remove any obstacle and then search for the logger again.
4 Set the measurement conditions in Wireless Logger Collector. (p.47)
(4)
(3)
(2) (1)

HIOKI LR8520B960-06

Measurement Workflow
5 Send the measurement conditions to the instrument. (p.65)
6 Start measurement. (p.67)
Please be advised that if you start recording, the previously acquired data retained in the internal memory will be deleted.
You can also start measurement by holding down this button.
7 Collect measurement data using Wireless Logger Collector. (p.70)
Measurement data can be collected during measurement and after measurement stop.

HIOKI LR8520B960-06

Installing the Software

8 Analyze the data on the Windows® PC.

1. Display measurement data in the The data is displayed in a graph and analyzed.

Logger Utility:

(p.71)

2. Output the collected data in the CSV file format: "Exporting measurement data" (p.72)

The data is displayed in a graph using a spreadsheet program, such as Microsoft® Excel®.

3.3 Installing the Software
Installation
Install the software according to the following procedure. Displayed messages and operations may be different depending on the operating system or settings.
1 Close all the software that is running.
IMPORTANT If any anti-virus software is running, make sure to close it before starting the installation. If anti-virus software is running, the software may not be installed properly.
2 Set the provided CD in the CD-ROM drive.

The language selection screen is automatically displayed. If the screen is not displayed, start the explorer to find the [index.htm] file and open it with a web browser.
3 Click [English]
The menu will appear.
4 Click [Logger Utility Wireless Logger Collector] 5 Click [Install]
The installer starts automatically. If the installer does not start, execute [Setup. exe] on the CD .
6 Install the software according to the instructions displayed by the
installer.
Two applications, Logger Utility and Wireless Logger Collector, are installed.

HIOKI LR8520B960-06

Installing the Software
Startup procedure
For Windows 7 From the Windows Start menu, click [All Programs] - [HIOKI] - [Logger Utility] [Wireless Logger Collector].
For Windows 8 From the Start window, display the [Apps] view and click [HIOKI] - [Wireless Logger Collector].
For Windows 10 From the Windows Start menu, click [All Apps] - [HIOKI] - [Wireless Logger Collector].
Termination procedure
In the main screen, click the application button and then click [Exit] in the displayed menu.

Or click the Close key [ ] at the upper right of the main screen.

HIOKI LR8520B960-06

Installing the Software
Uninstallation
Remove the software according to the following procedure.
1 Open Control Panel.
For Windows 7: From the Windows Start menu, click [Control Panel].
For Windows 8: From the Start window, display the [Apps] view and click [Windows System] [Control Panel].
For Windows 10: Right-click the Windows Start button, and then click [Control Panel].
2 Click [Programs and Features].
The [Uninstall or change a program] screen is displayed.
3 Double-click [HIOKI Logger Utility] in the list of installed programs.
As the measurement data and setting files remain as they are, delete them manually if they are not needed.

HIOKI LR8520B960-06

Display Configuration

3.4 Display Configuration

The main screen is displayed when the application starts up.

Name

Description

1 Application button

Displays the option menu, etc.

2 Quick access tool bar Right-click and customize the Ribbon bar.

3 Ribbon

Allows you to operate or edit the items displayed in the list.

4 Navigation bar

· Registers and sets wireless loggers. · Performs measurement and monitoring. · Collects and browses measurement data. · Performs wireless logger maintenance.

5 Wireless logger list (tree · Switches the group display and list display.

display)

· Creates and deletes groups.

6 Title display

Displays the information on the wireless logger that is currently selected.

7 Wireless logger/channel/file Displays the settings and wireless logger status. list (list display)

8 Output (log)

· Displays operation results and errors. · The log can be copied and cleared.

9 Status bar
38

· Number of items: Displays the total number of items. · Number of selections: Displays the number of selected items. · Status display: Sending/receiving settings, monitoring
status, controlling measurement, collecting data, performing maintenance HIOKI LR8520B960-06

Basic Operation Procedure
3.5 Basic Operation Procedure
Operation flow

1 Select one of the following categories from the Navigation bar.
[Register/Settings], [Measurement/Monitoring], [Collection/Browse], [Maintenance]
2 Select a group and wireless logger from the wireless logger list (tree
display).
3 Select the item to be displayed from the wireless logger/channel/file list
(list display).
4 Press the operation button of the Navigation bar.
Or right-click the item in the list and select the operation from the displayed menu.

HIOKI LR8520B960-06

Basic Operation Procedure
Selecting multiple wireless loggers
Search/Select From all the registered wireless loggers, communicative wireless loggers are searched for and selected automatically.
· This button may not be used depending on the PC specifications. · This button may not be selected depending on the communications with the
wireless logger.
Select all Click [Select All] on the Ribbon bar.
Unselect Click [Unselect] on the Ribbon bar.
Select individual Click a checkbox in the list.
Select multiple Click the item in the list while pressing the Ctrl key or Shift key.

· The number of selected items is displayed on the Status bar. · The checked items have priority over the selected items (highlighted items) in the
list.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
3.6 Registering/Deleting a Wireless Logger
Registering a wireless logger
Register a wireless logger in Wireless Logger Collector. Up to 100 wireless loggers can be registered.
IMPORTANT Some functions of Wireless Logger Collector may not be used depending on the PC specifications. Communications may not be established depending on the combination of the Bluetooth module and Bluetooth stack (device driver).
Preparation
1 Place the wireless logger near the Windows® PC (where there is no
communications interference).
2 Turn on the wireless logger power ( ).
(The instrument is powered up automatically when the AC adapter or battery is installed.) Check that the Bluetooth power is ON ( Lit).

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger Registration

1
3 2
4
5
1 Select [Register/Settings] - [Register/remove device] of the Navigation bar.
The [Register/remove device] dialog box is displayed.
2 Click [Search].
The nearby wireless loggers or wireless loggers that have been connected are displayed in the list on the left. (COM ports are displayed if a third party Bluetooth stack is used.)
3 Select the wireless logger(s) to be registered from the list on the left
(multiple units can be selected).
4 Press [ ] to register the selected wireless logger(s).
The selected wireless logger(s) moves to the list on the right.
5 Press [OK].

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
· When a Windows® standard Bluetooth stack is used, the model name and serial number are displayed in "Found devies". To check whether Windows® standard Bluetooth stack is enabled, select [Control Panel] - [Device Manager], open [Bluetooth Radios], and then check if [Microsoft Bluetooth Enumerator] is displayed.
· When a Windows® non-standard Bluetooth stack is used, the model name and serial number are not displayed. Make paring and virtual COM settings in the software provided with the Bluetooth stack and then register the wireless loggers. When an unauthorized virtual COM is registered, the operation of Wireless Logger Collector may become unstable. Ways of performing a pairing and creating a virtual serial port vary depending on your computer and Bluetooth stack. Please direct the inquiries to manufactures of them for details.
Example of how to allocate Virtual COM port
1 Open [Control Panel] - [Device and Printers] or [Bluetooth]. 2 Click [Add a device] and select a wireless logger which would like to
do a pairing. When a pairing is completed, the wireless logger is registered with a list.
3 Open [Property] of registered wireless logger and check the
assigned virtual COM port number.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
Deleting a wireless logger
Delete the wireless logger that is registered in Wireless Logger Collector (registration cancel).

1 2

4
1 Select [Register/Settings] - [Register/remove device] of the Navigation bar.
The [Register/remove device] dialog box is displayed.
2 Select the wireless logger(s) to be deleted from the list on the right
(multiple units can be selected).
3 Press [ ] to delete the selected wireless logger(s).
The selected wireless logger(s) moves to the list on the left.
4 Press [OK].
The collected measurement data is not deleted even when wireless loggers are deleted (registration cancel). Delete the measurement data manually if it is not needed.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
Grouping wireless loggers
Wireless loggers can be grouped and managed. Grouping is useful for managing multiple wireless loggers. Groups can be added to the layered structure. Procedure to create a group
2 1
1 From [List] (the wireless logger list [tree display]), select [Computer] or
the group for which a new group is to be created.
2 Press [ ].
A new group is now created.
3 Enter a group name and press the Enter key.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
Procedure to move a group From [List] (the wireless logger list [tree display]), drag the wireless logger to be moved using the left key of the mouse and drop it on the target group.
Drag and drop

Procedure to delete a group
2 1

1 From [List] (the wireless logger list [tree display]), select the group to be
deleted.
2 Press [ ].
If wireless loggers are registered in the deleted group, they move to under [Computer].

HIOKI LR8520B960-06

Setting Measurement Conditions
3.7 Setting Measurement Conditions
Set the measurement conditions for wireless loggers.
3
2 1

1 Select [Register/Settings] from the Navigation bar. 2 Select the target wireless logger. 3 Click [Open] on the Ribbon bar.
The settings dialog box is displayed.

HIOKI LR8520B960-06

Setting Measurement Conditions
Setting measurement
Recording Interval Allows you to set the interval to import data. Settings: 100ms, 200ms, 500ms, 1s, 2s, 5s, 10s, 20s, 30s, 1min, 2min, 5min, 10min, 20min, 30min, 1hour
Recording interval · Select the recording interval according to the object to be measured. · The data update of LR8520 is every 500ms. · The peak of the waveform may not be measured depending on the recording
interval setting. Example: When the recording interval is set to 1s.
Peak

Continuous Recording
Allows you to set a processing method when the memory is full. Settings:

Off (One-time) On (Endless)

Stops recording when the memory is full. Overwrites old data when the memory is full.

HIOKI LR8520B960-06

Setting Measurement Conditions

Title Comment
Allows you to set the title comment. (Up to 40 single-byte characters) The characters entered are converted to the following symbols.

2 (Superscript)

3 (Superscript)

Scheduled Record Start
Measurement can be started at the specified time. If the current time has passed the preset time, measurement is not started. Settings:

OFF (The preset start function is disabled.)

Starts recording at the preset time.

The instrument enters the recording start standby state at the same time as the Scheduled Record Start ON setting is sent. Measurement start by signal communications cannot be accepted in this state.

Scheduled Record Stop
Measurement can be stopped at the specified time. If the current time has passed the preset time, measurement is not stopped. Settings:

OFF (The preset stop function is disabled.)

Stops recording at the preset time.

HIOKI LR8520B960-06

Setting Measurement Conditions
Setting the channel
The channel to be set is switched.

Measurement
Allows you to set measurement to ON/OFF. Settings:

Does not perform measurement.

Performs measurement.

Comment
Allows you to set the channel comment. (Up to 40 single-byte characters) The characters entered are converted to the following symbols.

2 (Superscript)

3 (Superscript)

HIOKI LR8520B960-06

Setting Measurement Conditions
Making settings for temperature and humidity measurement The temperature and humidity are measured using the Z2010/Z2011 Temperature and Humidity Sensor.
1
: ON
1 Select the channel to be set and check the Measurement checkbox [] (ON).
Disconnection [BURN OUT] is displayed for the measurement value and [BURN] is displayed on the screen under the following conditions. The saved data will include values listed in "Data Handling" in the Appendix (p.Appx.2). · When the temperature and humidity sensor is not connected · When the cable of the temperature and humidity sensor is cut · When the temperature and humidity sensor fails · When a communications error occurs with the temperature and humidity sensor due to
noise
Channel numbers Each channel indicates the following measurement values. CH1T Temperature CH1H Humidity CH1F Fungal index CH1G Predicted fungal growth
If the waveform level significantly exceeds the measurable scope of each range, measured values will be treated as [+OVER] or [-OVER] with [O.F.] or [U.F.] displayed, respectively. The saved data will include values listed in "Handling Data" in the Appendix (p.Appx.2).

HIOKI LR8520B960-06

Setting Measurement Conditions
Setting scaling (as needed)
The input value can be converted to a physical quantity of the object to be measured from voltage to current, etc.

Normal display (OFF)

With scaling

1 3 2 4

1 Select the display format of the scaling value.

Settings: OFF
Decimal
Exponential

No scaling Displays the converted value as a decimal number. Displays the converted value as an index number. Wireless logger display is in a decimal number only.

2 Select the scaling method.

Settings:

Set by Ratio

Converts the value to a physical quantity (conversion ratio) per 1 V of the input signal, offset, and unit.

Set by 2 Points

Converts the value voltage at 2 points of the input signal and the converted value and unit of the 2 points.

HIOKI LR8520B960-06

Setting Measurement Conditions

3 Set the unit to be converted (up to 7 single-byte characters).
The characters entered are converted to the following symbols.

2 (Superscript)

3 (Superscript)

4 When Ratio is selected, set the conversion ratio and offset.
When 2 Points is selected, set the value for 2 points before and after conversion.

Setting by the ratio

Setting by 2 points

Unit [A]

Unit (eu)

(Example)

Conversion 1: VH value to AH value Conversion 2: VL value to AL value

Inclination (Conversion

ratio: eu/v)

Offset

VH: High potential point AH: Value for high potential point VL: Low potential point AL: Value for low potential point

[V]

Value of the unit to be converted

Actual measurement value (input value)

Setting the displayed digit under decimal point The measurement value is displayed with the decimal point fixed to the specified digit.

Settings:
AUTO
0 Digit/1 Digit/ 2 Digit/3 Digit

Displays a 4-digit value (0.000 to ±9,999). The decimal point position is changed as needed.
The decimal point is fixed to the specified digit.

Setting the auxiliary unit
The value obtained when the measurement value is multiplied by the constant shown in the following table is displayed in the wireless logger screen. (The measurement value is not affected.)

Settings: (micro) m (milli) k (kilo) M (mega)

×106 ×103 ×1 ×10-3 ×10-6

Reset
The conversion parameter (conversion ratio, offset, input, output) is restored to the default setting.

HIOKI LR8520B960-06

Setting Measurement Conditions
When a temperature measuring channel is selected, clicking [Fahrenheit] switches over the scaling setting to Fahrenheit mode automatically. [Units]: °F [Ratio]: 1.8 [Offset]: 32

HIOKI LR8520B960-06

Setting Measurement Conditions
Setting the alarm function (as needed)
Make the alarm settings.

Alarm Settings
Allows you to set the alarm function to ON/OFF. Settings:

OFF ON

Alarm function OFF Alarm function ON

Hold Alarm Allows you to set the alarm hold function to ON/OFF. Whether or not to hold the alarm is set.
Settings:

OFF ON

Cancels the alarm when the alarm conditions are no longer met. Holds the alarm.

Composite Condition Performs logic synthesis for the alarm between channels. Settings:

OR (Between channels)
AND (Between channels)

When the alarm conditions for a channel are met, judges it to be an alarm.
When the alarm conditions at all channels are met, judges it to be an alarm.

HIOKI LR8520B960-06

Setting Measurement Conditions

Alarm output Allows you to set whether or not to output a signal from the terminal when the alarm conditions are met.
Settings:

OFF ON

Does not output a signal from the output terminal even when the alarm conditions are met.
Outputs a signal from the terminal when the alarm conditions are met.

Setting the alarm for each channel Allows you to set the alarm conditions for each channel.

Alarm Method Settings: OFF Level Window In
Window Out

Does not perform alarm judgment.
When the specified level is reached, judges it to be an alarm.
When a value is inside of the specified upper and lower limit range, judges it to be an alarm.
When a value is outside of the specified upper and lower limit range, judges it to be an alarm.

HIOKI LR8520B960-06

Setting Measurement Conditions

Alarm Level, HIGH/LOW (When Alarm Method is set to Level) Settings:

HIGH LOW

When a value is more than the specified level value, judges it to be an alarm.
When a value is less than the specified level value, judges it to be an alarm.

Upper Limit, Lower Limit (When Alarm Method is set to Window In, Window Out)
The judgment level value (upper/lower limit) is set.

HIOKI LR8520B960-06

Setting Measurement Conditions
Setting the power saving function (as needed)
Setting the Bluetooth module power to OFF can save the battery life.

Schedule
The method to turn ON/OFF the Bluetooth module power is set. Settings:

OFF Every Day Every Week
Every Month

Does not turn ON/OFF the Bluetooth module power.
Turns ON the Bluetooth module power at the specified time.
Turns ON the Bluetooth module power at the specified time on the specified day (Sunday to Saturday).
Turns ON the Bluetooth module power at the specified time on the specified date (1st to 31st). When the specified date does not exist, it is ignored.

Starting Communication Reception The clock time to turn ON the Bluetooth module power is set. Settings:

Allowable setting range

00:00 to 23:59

Continuous Reception Time The period when the Bluetooth module power is ON is set. Settings:

Allowable setting range

10 minutes to 12 hours

· After the power saving function is set, press the power key to turn OFF the Bluetooth module power.
· When the power saving function is enabled and the Bluetooth module power is
OFF, the Bluetooth symbol ( ) blinks.

HIOKI LR8520B960-06

Setting the environment

Setting Measurement Conditions

Prevent a wrong key operation of the body
A confirmation message can be displayed at the time of measurement start, stop, and power OFF to prevent operational errors. Settings:

Does not display a confirmation message.

Displays a confirmation message.

· Press the · Press the

(YES) key to continue the operation. (NO) key to cancel the operation.

· The operation is automatically canceled when the key is not pressed for 10 seconds.

Start Backup
Recording can be resumed when the power is lost due to a power outage, etc. during recording operation and the power is turned ON again. Settings:

Does not use the start backup function.

Uses the start backup function.

· Measurement is resumed to the point of the measurement data before a power outage. The data during the power outage is indicated as [NO DATA]. The saved data will include values listed in "Data Handling" in the Appendix (p.Appx.2).
· If a power outage continues for an extended period of time (period over recording interval × 250,000 data), the measurement data prior to the power outage is discarded and new measurement starts.

HIOKI LR8520B960-06

Setting Measurement Conditions

Free Run
The measurement value is indicated every 1 second while measurement is stopped. (the data is not saved in the memory). The measurement value is saved in the memory and indicated every 1 second regardless of recording interval setting while measuring. (when the setting of recording interval is less than 1 second, the measurement value is indicated every recording interval) Settings:

Does not use the free-running function.

Use the free-running function.

When the free run function is used, a battery is consumed big because the measurement is performed every 1 second, so when doing battery drive, please be careful about a battery remaining amount.

HIOKI LR8520B960-06

Setting Measurement Conditions
Communications
The communications settings of registered wireless loggers are changed.

Identification name change
You can name the wireless logger to be identified (up to 16 single-byte characters). The characters entered are converted to the following symbols.

2 (Superscript)

3 (Superscript)

Bluetooth COM
The communications port setting cannot be changed.
· Normally this setting does not need to be changed. Change the setting only when a connection cannot be established.
· If no virtual COM is registered in Windows®, the COM number is not displayed in the options. For details on how to create a virtual COM port, contact the manufacturer.
· If a COM number that is not related to the registered device is specified, communications cannot be established.

HIOKI LR8520B960-06

Setting Measurement Conditions

Security
The authentication function using a password can be enabled to prevent the wireless logger from being controlled remotely without due care by a third party. Press [Reset Password] to change the password.
Settings:

Disables authentication.

Enables authentication.

Enter the password for authentication (up to 20 single-byte characters).

The password is not set at the time of shipment (no characters).

IMPORTANT
· Be aware that the wireless logger cannot be controlled at all if you forget the password.
· When the password is not correct, "Authentication Error" is displayed in the output (log) and setting sending/receiving, measurement start/stop, status monitoring, data collection, and maintenance cannot be performed.

HIOKI LR8520B960-06

Setting Measurement Conditions

Copying the settings
The settings of a particular wireless logger can be copied to another wireless logger. The settings of a particular channel can also be copied to another channel. Some settings cannot be copied if the wireless logger type is different.

2, 4

1 Select [Register/Settings] from the Navigation bar. 2 Select the wireless logger or channel from which the settings are copied. 3 Press [Copy] on the Ribbon bar. 4 Select the wireless logger or channel to which the settings are copied. 5 Press [Paste] on the Ribbon bar.

HIOKI LR8520B960-06

Setting Measurement Conditions
Initializing the settings
The settings are restored to the default values. (p.Appx.2)

3
1 Select [Register/Settings] from the Navigation bar. 2 Select the target wireless logger. 3 Click [Clear].

HIOKI LR8520B960-06

Sending/Receiving the Setting Conditions
3.8 Sending/Receiving the Setting Conditions
Sending the settings
The setting conditions edited in Wireless Logger Collector are sent to and set for wireless loggers using wireless communications.

3
1 Select [Register/Settings] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Send].

HIOKI LR8520B960-06

Sending/Receiving the Setting Conditions
Receiving the settings
The settings of the current wireless logger are received by Wireless Logger Collector using wireless communications.

3
1 Select [Register/Settings] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Receive].
When the settings are received, the settings of the corresponding unit are all overwritten. The settings cannot be restored once they are overwritten.

HIOKI LR8520B960-06

Starting and Stopping Measurement and Monitoring
3.9 Starting and Stopping Measurement and Monitoring
Starting and stopping measurement
Wireless logger measurement is started and stopped.
2 1
3

1 Select [Measurement/Monitoring] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Start] or [Stop].
When measurement start is preset, measurement does not start until the preset time.

HIOKI LR8520B960-06

Starting and Stopping Measurement and Monitoring
Starting and stopping status monitoring
The wireless logger status is periodically monitored. The status is periodically monitored until the status monitoring is stopped once the monitoring interval is set. (p.81) Items to be monitored: Measurement status, latest measurement data, battery level, wireless signal level The monitoring result is displayed in each line of the list.
2 1
3
1 Select [Measurement/Monitoring] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Start Monitoring] or [Stop Monitoring].

HIOKI LR8520B960-06

Starting and Stopping Measurement and Monitoring
Starting and stopping value monitoring 3 2
1

1 Select [Measurement/Monitoring] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Open] on the Ribbon bar.
The value monitor screen is displayed.
: Close button

: Start monitoring

: Stop monitoring

: Measuring

: Monitoring

Monitoring value (updated every second)

(None): :

Measurement/monitoring stopped
Battery level

: AC adapter is used

Wireless signal level

· When the selected wireless logger is being measured, the latest measurement data is displayed. · When the selected wireless logger is not being measured, the monitoring operation starts. · The wireless logger remains connected wirelessly and the communications of the target
wireless logger is occupied. In this state, the settings cannot be sent to or received from the target wireless logger and measurement start/stop, measurement data collection, and maintenance cannot be performed.

HIOKI LR8520B960-06

Collecting Measurement Data
3.10 Collecting Measurement Data
Starting and stopping data collection
Measurement data is collected from wireless loggers. Measurement data can be collected even while wireless loggers are being measured. Measurement data is periodically collected until the data collection is stopped once the collection interval is set. (p.81)
2 1
3

1 Select [Collection/Browse] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Start Collection] or [Stop Collection].

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data
3.11 Browsing/Analyzing Measurement Data
Browsing measurement data
Collected measurement data can be displayed in a waveform using the Logger Utility.

3 4

1 Select [Collection/Browse] from the Navigation bar. 2 Double-click the target wireless logger in the list using the mouse.
The list switches to the collected measurement data (file) list.
3 Select the measurement data to be browsed from the list. 4 Press [Open Logger Utility].
For details, refer to the Logger Utility instruction manual on the provided CD.

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data
Exporting measurement data
Measurement data can be output in various formats. Use this function to analyze measurement data using software like Microsoft® Excel®.

1 Select [Collection/Browse] from the Navigation bar. 2 Double-click the target wireless logger in the list using the mouse.
The list switches to the collected measurement data (file) list.
3 Select the measurement data to be exported from the list.
You can select multiple measurement data. (p.40)
4 Press [Export data].
The [Export Measurement Data] dialog box is displayed.

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data

5 Select the file type.
When you want to combine multiple measurement data files to 1 file, please choose [Logger Utility General-purpose Data Format].
Settings:
Compatible Logger Utility Format, Logger Utility General-purpose Data Format [File Combination], LR5000 Format and Smart Site Format, LR5000 Format, CSV (Comma), Text (delineated by semicolon), Text (delineated by space), Text (delineated by tab)
6 (For CSV or text format) Make detail settings.
Settings:

Decimal point Time Axis Format File Division Thin Out Comment Time Format Text Format

Dot, Comma Absolute Time, Relative Time, Second, Point Do not split, Splitting by data number (1,000 to 2,000,000), Splitting by date 1 to 10,000 None, Header, Value, Header and Data Sections yyyy/mm/dd HH:MM:SS, dd/mm/yyy HH:MM:SS, mm/dd/yyyy HH:MM:SS Exponential, Decimal

7 Select the location where the settings are to be saved.
Press [Browse] and select the destination folder.
8 Press [Go].
When [Open Folder After Export] is checked, the saved folder is opened in Explorer after the export is completed.

· The file to be exported is automatically named. Any file with the same name as a file that exists in the folder to which the file is to be exported is overwritten. If you do not want any file to be overwritten, create a new folder and then change the location to save the file.
· The Logger Utility General-purpose Data Format (*.lux) cannot be converted
under the following conditions.
(1) When 100 or more files are selected (2) When the total number of channels recorded in the selected file exceeds 270

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data
Deleting measurement data
Collected measurement data can be deleted.
1 Select [Collection/Browse] from the Navigation bar. 2 Select the target wireless logger. 3 Double-click the target wireless logger in the list using the mouse.
The list switches to the collected measurement data (file) list.
4 Select the measurement data to be deleted from the list. 5 Press [Delete Data].
Once the measurement data is deleted, it cannot be restored.

HIOKI LR8520B960-06

Performing Wireless Logger Maintenance
3.12 Performing Wireless Logger Maintenance
Setting the clock
The wireless logger clock is set according to the Windows® PC clock.
2 1
3
1 Select [Maintenance] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Adjust Clock].
The clock cannot be set during wireless logger measurement and monitoring.

HIOKI LR8520B960-06

Performing Wireless Logger Maintenance
Self-diagnosis
Self-diagnosis of wireless loggers is executed.
2 1
3
1 Select [Maintenance] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Self-Test].
Self-diagnosis takes approximately 2 minutes. If the self-diagnosis result is displayed as [Error], the instrument needs to be repaired or inspected. Contact your authorized Hioki distributor or reseller.

HIOKI LR8520B960-06

Performing Wireless Logger Maintenance
Checking the version number
The firmware version of wireless loggers is checked.
2 1
3
1 Select [Maintenance] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Version Check].

HIOKI LR8520B960-06

Performing Wireless Logger Maintenance
Updating the firmware version
The firmware version of wireless loggers is updated.
2 1

3
1 Select [Maintenance] from the Navigation bar. 2 Select the target wireless logger. 3 Press [Version Upgrade].
The latest update file version can be downloaded from our Internet website. Execute [Import Version Upgrade File] in the menu to load the downloaded file to Wireless Logger Collector.
CAUTION
· Never turn OFF the power of the wireless logger that is being updated. The wireless logger needs to be repaired and inspected if the power is turned OFF during update.
· As measurement data and settings are erased, back up the data and settings as needed.

HIOKI LR8520B960-06

3.13 Convenient Functions

Convenient Functions

Column The description to be displayed in the list (wireless logger/channel/file) can be selected. Font Size The size of letters in the list can be changed. Settings Small, Standard, Medium, Large, Extra Large
Language The display language for the application is switched. Restart the application to reflect the change. Settings Japanese, English, Chinese
Style The color scheme for the application is switched. Settings Style 1 to 11

HIOKI LR8520B960-06

Convenient Functions
Caption Bar, Output Window, Status Bar The window display/non-display status is switched.
Version Information The version information of the application is displayed.
Import Data File to Application Measurement files (in LUW format) exported through the Android version of Wireless Logger Collector are imported to Wireless Logger Collector.
Export Application Data File This function can be used when the Windows® PC is transferred or backed up. The registered wireless logger information and collected measurement data can be output all together as one file.
Import Application Data File The backed up file is loaded to Wireless Logger Collector.
Communications may not be established via Bluetooth if the PC environment is different. Perform registration and deletion of the wireless loggers again. (p.41)
Import Version Upgrade File A firmware version upgrade file is loaded to Wireless Logger Collector. (p.78)

HIOKI LR8520B960-06

Option The optional functions are set.

Convenient Functions
Set the number of simultaneous connections. Set the monitor interval. Set the collection interval.

Max. Connectable Devices Settings (*: Default settings) 1* to 7 device(s)
The number of simultaneous connections may be limited depending on the PC environment.
Monitor Interval Settings (*: Default settings) Once*, 10 minutes, 30 minutes, 1 hour, 2 hours, 6 hours, 12 hours, 1 day Collection Interval Settings (*: Default settings) Once*, 10 minutes, 30 minutes, 1 hour, 2 hours, 6 hours, 12 hours, 1 day

HIOKI LR8520B960-06

Convenient Functions

HIOKI LR8520B960-06

Collecting Measurement Data Using an AndroidTM Terminal

· Android tablet · Android smartphone

(Line-of-sight 30 m)

USB

Windows® PC

4.1 Software Specifications
System requirements

Android OS
Recommended display size
Communication method

4.0.3 or later 7 inches or larger
Bluetooth 2.1+EDR or higher Profile: SPP

Function specifications

Number of allowable registrations

100 units

Settings

Measurement settings can be edited/initialized and sent/received.

Measurement control

Measurement can be started and stopped.

Monitoring function

Numerical values can be monitored. Update interval: 1 second

Measurement data Measurement data can be downloaded. collection function

Browse

Measurement data can be displayed.

Measurement data Measurement data can be output to a file in the following formats.

output

Logger utility format

Other

The clock can be set and the version number can be checked.

The terms and button display and arrangement may be different depending on the Android terminal.

HIOKI LR8520B960-06

Measurement Workflow
4.2 Measurement Workflow 1 Install the instrument referring to "Preparation for Measurements"
(p.21).
2 Install Wireless Logger Collector on the Android terminal. (p.87)
Wireless Logger Collector
3 Register the instrument in Wireless Logger Collector (up to 100 units).
(p.94)
4 Set the measurement conditions in Wireless Logger Collector and send
the conditions to the instrument. (p.98)
(3) (2)

(1)

(4)

HIOKI LR8520B960-06

5 Start measurement. (p.105)
(2)

Measurement Workflow

(3)
(1)
6 Collect measurement data using Wireless Logger Collector. (p.108)
(2)

(3) (1)

HIOKI LR8520B960-06

Measurement Workflow
7 Export the measurement data to a file. (p.111)
(2) (3)
(1)

(5)

(4)

8 Copy the exported file onto the Windows® PC. (p.112)
USB cable

9 Analyze the data on the Windows® PC.

HIOKI LR8520B960-06

Installing the Software
4.3 Installing the Software
Installation
Go to "Google PlayTM Store" and download Wireless Logger Collector.

Tap [Play Store] in the application screen. [Play Store] may not be available on some models.

Tap the [Search] button.

Tap [Wireless Logger Collector] in the search results. Install the software according to the instructions displayed in the screen.

Enter a key word.
Wireless Logger Collector

When the installation is completed, application screen.

[Wireless Logger Collector] is added to the

HIOKI LR8520B960-06

Installing the Software

Startup procedure
In the application screen, tap

[Wireless Logger Collector].

Uninstallation
The application can be removed from "Google Play Store" or the [Settings] - [Apps] screen.
IMPORTANT When the application is uninstalled, the wireless logger registration information, settings, and collected measurement data are erased. Export and store the collected measurement data prior to uninstallation.

HIOKI LR8520B960-06

Display Configuration

4.4 Display Configuration

Main screen

Wireless logger search and registration Wireless logger monitoring status

Registered wireless loggers

Menu buttons

Back

Group name
Operation buttons · Settings · Measurement · Collection · Browse

HIOKI LR8520B960-06

Display Configuration
Monitor screen

Wireless logger status Latest measurement data
Trend waveform (Update interval: 1 second, up to 100 data)

HIOKI LR8520B960-06

Settings screen

Display Configuration

Discards the changed settings. Confirms and saves the changed settings. Receives all settings from the selected wireless logger. Sends all settings to the selected wireless logger.

HIOKI LR8520B960-06

Display Configuration
Browse screen

Title comment

Collection date and time
Number of data Measurement start date and time

HIOKI LR8520B960-06

Graph screen
Displayed waveforms can be expanded or compressed along the horizontal axis.
The display range can be adjusted.
Select channel for gauge display.

Display Configuration
Jump to the specified time.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
4.5 Registering/Deleting a Wireless Logger
Registering a wireless logger
Register a wireless logger in Wireless Logger Collector. Up to 100 wireless loggers can be registered.
1
2

1 Tap [

The search result list is displayed. It may take several tens of seconds to search for wireless loggers. The wireless loggers that are located nearby and are not registered are displayed in the search result list.
2 Select the wireless logger to be registered.
The newly registered wireless logger is displayed under [Basic Group].

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
Deleting a wireless logger
Units that are registered in Wireless Logger Collector are deleted (registration cancel).
1
2
1 Tap the menu button. 2 Tap [Remove Logger]. 3 Select the group to which the wireless logger to be deleted belongs. 4 Select the wireless logger to be deleted.
IMPORTANT When wireless loggers are deleted (registration canceled), the settings and collected measurement data are also deleted. Export and store the collected measurement data prior to deleting a wireless logger.

HIOKI LR8520B960-06

Registering/Deleting a Wireless Logger
Grouping wireless loggers
Wireless loggers can be grouped and managed. Grouping is useful for managing multiple wireless loggers. Procedure to create a group
1 2
1 Tap the menu button. 2 Tap [Add Group]. 3 Enter a new group name.
A new group is now created at the very bottom of the list.

HIOKI LR8520B960-06

Changing the group

Registering/Deleting a Wireless Logger
1 2

1 Tap the menu button. 2 Tap [Change Group]. 3 Select the current group. 4 Select the wireless logger to be moved. 5 Select the group to which the wireless logger is to be moved.
Procedure to delete a group
1
2

1 Tap the menu button. 2 Tap [Remove Group]. 3 Select the group to be deleted.
If wireless loggers are registered in the deleted group, they move to under [Basic Group].

HIOKI LR8520B960-06

Setting Measurement Conditions
4.6 Setting Measurement Conditions
Set the measurement conditions for wireless loggers. For details on settings, see "3.7 Setting Measurement Conditions" (p. 47).

1
1 Tap [Settings] button. 2 Tap the wireless logger for which the settings are to be changed.
The settings screen is displayed.
3 Set the measurement conditions.

HIOKI LR8520B960-06

Setting measurement

Setting Measurement Conditions

Title Comment Allows you to set the title comment. (up to 40 single-byte characters)
Identifier Name You can name the wireless logger to be identified (up to 16 single-byte characters).
Recording Interval Allows you to set the interval to import data.
Continuous Recording Allows you to set a processing method when the memory is full.

HIOKI LR8520B960-06

Setting Measurement Conditions

Setting the channel
Set the input, scaling, and alarm for each channel.

Settings screen

Scaling settings screen

Alarm settings screen

100

HIOKI LR8520B960-06

Advance settings

Setting Measurement Conditions

Record Schedule Scheduled Record Start Measurement can be started at the specified time. Scheduled Record Stop Measurement can be stopped at the specified time.

Power Save

Schedule

The time to turn ON/OFF the Bluetooth module power is set. Setting the Bluetooth module power to OFF can save the battery life.

Starting Communication The clock time to turn ON the Bluetooth module power is set. Reception

Continuous Reception The period when the Bluetooth module power is ON is set. Time

Security
An authentication function using a password can be enabled to prevent the unit from being controlled carelessly by a third party. When changing the password, set a new password. As the old password is required for sending the settings, enter the old password.

Environment

Prevent a Wrong Key Operation on the Body
Start Backup

A confirmation message can be displayed at the time of measurement start, stop, and power OFF to prevent operational errors.
Recording can be resumed when the power is lost due to a power outage, etc. during recording operation and the power is turned ON again.

HIOKI LR8520B960-06

101

Setting Measurement Conditions

Free Run

The measurement value is indicated every 1 second while measurement is stopped. (the data is not saved in the memory) The measurement value is saved in the memory and indicated every 1 second regardless of recording interval setting while measuring. (when the setting of recording interval is less than 1 second, the measurement value is indicated every recording interval)

Initializing the setting
The settings are restored to the default values. (p.Appx.5)
1 2

1 Tap the menu button. 2 Tap [Initialize Settings].

102

HIOKI LR8520B960-06

Sending/Receiving the Setting Conditions
4.7 Sending/Receiving the Setting Conditions
Sending the settings
The settings edited on the applications are sent to and set for wireless loggers using wireless communications.
2

1 Tap the [Settings] button. 2 Tap the wireless logger to be edited.
The settings screen is displayed.
3 Tap the [Send] button.
The measurement settings are sent to the wireless logger.

HIOKI LR8520B960-06

103

Sending/Receiving the Setting Conditions
Receiving the settings
The settings of the current wireless logger are received by the application using wireless communications.
2

1 Tap the [Settings] button. 2 Tap the wireless logger to which the settings are to be sent.
The settings screen is displayed.
3 Tap the [Receive] button.
The measurement settings are sent from the wireless logger.

104

HIOKI LR8520B960-06

Starting and Stopping Measurement and Monitoring
4.8 Starting and Stopping Measurement and Monitoring
Starting and stopping measurement
Wireless logger measurement is started and stopped.
2
3
1
1 Tap the [Measure] button. 2 Tap the wireless logger for which measurement is to be started or stopped.
The menu is displayed.
3 Select [Start Measurement] or [Stop Measurement] from the menu.

HIOKI LR8520B960-06

105

Starting and Stopping Measurement and Monitoring
Starting and stopping monitoring
Checking the latest status of wireless loggers The current status of wireless loggers can be checked. The measurement status, power status (battery level), and wireless signal level can be checked.

Tap [ ] at the top of the screen. The status of all the registered wireless loggers is acquired only once.

Item Power

Icon AC

Description

Battery (level 1) It is recommended to replace the batteries.

Battery (level 2)

Wireless signal level

Battery (level 3) Level 1 (low)

Level 2 (slightly low)

Measurement status

Level 3 (good) Measuring

Waiting for preset measurement start

Waiting for preset measurement stop

Status check time

(None)

Monitoring Elapsed time from the last check

106

HIOKI LR8520B960-06

Starting and Stopping Measurement and Monitoring
Checking the latest data of wireless loggers The latest measurement data of the wireless loggers that are being measured can be checked in the waveform and value formats. This is useful for checking measurement before installation.
2
3
1
1 Tap the [Measure] button. 2 Tap the wireless logger to be monitored.
The menu is displayed.
3 Tap [Start Monitoring] in the menu.
The monitoring screen is displayed. (p.90) The monitoring value is updated every second.
· When the selected wireless logger is being measured, the latest measurement data is displayed.
· When the selected wireless logger is not being measured, the monitoring operation starts. Send and set the measurement conditions to the wireless logger in advance.

HIOKI LR8520B960-06

107

Collecting Measurement Data
4.9 Collecting Measurement Data
Measurement data is collected from wireless loggers.
Starting and stopping data collection
Measurement data is collected from wireless loggers. Measurement data can also be collected during measurement.
2
3
1
1 Tap the [Collection] button. 2 Tap the wireless logger from which the measurement data is to be
collected. The menu is displayed.
3 Select [Start Collection] from the menu.
Select [Stop Collection] if you want to stop the data collection.

108

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data

4.10 Browsing/Analyzing Measurement Data
Browsing measurement data
The collected measurement data can be displayed on the screen.

HIOKI LR8520B960-06

109

Browsing/Analyzing Measurement Data
1 Tap the [Browse] button. 2 Tap the wireless logger for which the measurement data is to be browsed.
The browsing screen is displayed. (p.92)
3 Tap the collected measurement data to be displayed.
The menu is displayed.
4 Tap [Show Graph].

110

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data
Exporting measurement data
The collected measurement data can be output to a file to use it on the Windows® PC, etc.
2 3
1

1 Tap the [Browse] button. 2 Tap the wireless logger for which the measurement data is to be browsed.
The browsing screen is displayed.
3 Tap the collected measurement data to be output.
The menu is displayed.
4 Tap [Export Data].

HIOKI LR8520B960-06

111

Browsing/Analyzing Measurement Data
5 Select the location where the data is to be output to.
The measurement data is output in the LUW format. A LUW file can be browsed/analyzed using the supplied Logger Utility. The following folder is automatically created on the media of the selected location. A file name is automatically generated. [HIOKI] - [Wireless Logger Collector] - [Model number and serial number]
Copying the output file onto the Windows® PC When the file is output to the internal storage of the Android terminal (USB cable required)
1 Connect the Android terminal to the Windows® PC using a USB cable.
USB cable
The icon for the connected Android terminal is displayed under [Computer] on the Windows® PC.

112

HIOKI LR8520B960-06

Browsing/Analyzing Measurement Data
2 Double-click the Android terminal icon.
The list of media connected to the Android terminal is displayed.

3 Double-click [Internal storage] in the list of connected media. 4 Copy the output file onto the local drive on the Windows® PC.
Browse/analyze the file using the supplied Logger Utility.
When the file is output to an external medium (SD card, USB flash drive, etc.)
1 Remove the medium from the Android terminal and connect it to the
Windows® PC. The icon for the connected medium is displayed under [Computer] on the Windows® PC.
2 Copy the output file onto the local drive on the Windows® PC.
Browse/analyze the file using the supplied Logger Utility.

HIOKI LR8520B960-06

113

Browsing/Analyzing Measurement Data
Deleting measurement data
Collected measurement data can be deleted.
2 3
1

4
1 Tap the [Browse] button. 2 Tap the wireless logger for which the measurement data is to be deleted.
The browsing screen is displayed.
3 Tap the measurement data to be deleted.
The menu is displayed.
4 Tap [Delete Data].
IMPORTANT Be aware that once measurement data is deleted, it cannot be restored.

114

HIOKI LR8520B960-06

Performing Wireless Logger Maintenance
4.11 Performing Wireless Logger Maintenance
The wireless logger clock can be set and the version information can be displayed.
1 3
2

1 Tap the menu button. 2 Tap [Maintenance].
The system enters the maintenance mode.
3 Select the wireless logger for which maintenance is to be performed.
The menu is displayed.
4 Select [Adjust Clock] or [Version Check] in the menu. 5 End the maintenance mode.
To end the maintenance mode, tap [Exit Maintenance Mode].
SS

HIOKI LR8520B960-06

115

Performing Wireless Logger Maintenance
Setting the clock
The wireless logger clock is set according to the Android terminal clock. The clock cannot be set during wireless logger measurement and monitoring.
Checking the version number
The wireless logger version number is displayed.

116

HIOKI LR8520B960-06

5 Specifications

5.1 LR8520 Wireless Fungal Logger

Basic specifications

Product warranty period

3 years

Supported instrument

Used as a unit:

· LR8410 Wireless Logging Station

(Real-time measurement)

Used as a stand-alone device: (Manual data collection)

· Windows® PC or Windows® tablet (Wireless Logger Collector is used.)
· Android smartphone or Android tablet terminal (Wireless Logger Collector for Android is used.) (Settings can be made only from the supported equipment.)

Control communications method

Bluetooth 2.1+EDR Communications distance: 30 m (line-of-sight distance) (The distance for equipment other than the LR8410 depends on the performance of the equipment to be communicated with.) Security SSP Profile SPP

Clock function

Auto-calendar, automatic leap year adjustment, and 24-hour clock

Clock accuracy

±50 ppm (reference value at temperature of 23°C) ±4.32 seconds per day

Recording interval

0.5 sec./1 sec./2 sec./5 sec./10 sec./20 sec./30 sec., 1 min./2 min./5 min./10 min./20 min./30 min., 1 hour

Recording mode

Instant value recording: Records an instant value for each recording interval.

Continuous recording

ON/OFF selection ON: Deletes old data and continues recording when the
recording capacity is full (endless recording). OFF: Ends recording when the recording capacity is full (one-time
recording). (ON is automatically set when the instrument is used as a unit.)

Internal memory

Non-volatile memory (flash memory)

Recording capacity

500,000 data for each channel

Recording start method Key operation/Preset time/Command (communications from supported equipment by Bluetooth)

Recording stop method Key operation/Preset time/Command (communications from supported equipment by Bluetooth)/Automatic stop by one-time recording

HIOKI LR8520B960-06

117

LR8520 Wireless Fungal Logger

Backup

Recorded data, setting conditions (not deleted due to power shutdown)

Clock backup battery life

Approx. 5 years (reference value at 23°C) When the power is supplied by the AC adapter, batteries, or external power supply, the clock backup battery does not drain.

Display

LCD display

Display items

Temperature measurement value, humidity measurement value, measurement channel, unit (°C, °F, %, r/s, W, h, V, A, k, m), recording, recording mode, unit number, date, time, alarm, communications status, AC adapter connected, battery indicator (3 levels), number of recorded data, maximum value, minimum value, average value, fungal index (0 to 200), predicted fungal growth (5 levels)

Operation keys

[POWER] [REC/STOP] [DATA/INFO]

Power saving setting

Bluetooth standby can be turned ON/OFF by [POWER] key operation. ON: Accepts Bluetooth connection. OFF: Rejects Bluetooth connection.

Operating environment Indoors, Pollution Degree 2, altitude up to 2,000 m (6,562 ft.)

Operating temperature and humidity

Temperature: -20°C to 60°C (-4.0°F to 140.0°F) Humidity: 80% RH or less (non-condensation) (The operating temperature and humidity depend on the battery specifications when batteries are used.)

Storage temperature and humidity

Temperature: -20°C to 60°C (-4.0°F to 140.0°F) Humidity: 80% RH or less (non-condensation) (With batteries removed)

Temperature and humidity for guaranteed accuracy (Z2010/Z2011 used)

· At temperature measurement (sensor only) Temperature: -40°C to 80°C (-40.0 to 176.0°F) (Only the operating temperature and humidity of the logger when Z2010 is used) Humidity: 80% RH or less (non-condensation)
· At humidity measurement (sensor only) Temperature: 10°C to 60°C (50.0°F to 140.0°F) Humidity: 10% RH to 90% RH (non-condensation)

Dimensions

Approx. 85W×61H×31D mm (3.35"W×2.40"H×1.22"D) (Projections not included)

Mass

Approx. 95 g (3.4 oz.) (Batteries not included)

Standards

Safety: EN61010 EMC: EN61326, Class A

Vibration resistance

JIS D 1601:1995 5.3 (1), Class 1: Passenger vehicle, Condition: Equivalent to Class A (4 h in the X direction, 2 h in the Y and Z directions at a vibration acceleration of 45 m/s2 [4.6 G])

Dustproof and waterproof

None

118

HIOKI LR8520B960-06

LR8520 Wireless Fungal Logger

Input

Number of input channels

Temperature 1 channel + humidity 1 channel (1 sensor can be installed.)

Sensor

External temperature and humidity sensor (Z2010/Z2011 Humidity Sensor) Temperature 1 channel (semi-conductor sensor) + humidity 1 sensor (capacitance humidity sensor)

Measurement range/ allowable measurement range/resolution

Measurement target
Temperature

Range

Maximum resolution

100°C f.s.

0.1°C

Allowable measurement
range
-40°C to 80°C

Humidity

100% RH f.s.

0.1 % RH 0% RH to 100% RH

Temperature

±0.5°C (10°C to 60°C)

measurement accuracy If the temperature is outside of the range

(Z2010/Z2011 used)* Add 0.015°C/°C (-40°C to 10°C) or 0.02°C/°C (60°C to 80°C).

* The measurement accuracy depends only on the sensor.

Humidity measurement ±3% RH (20°C to 30°C , 20% RH to 90% RH)

accuracy

See the figure below if the humidity is outside of the range.

(Z2010/Z2011 used)*

Relative humidity [% RH]

100

±8% RH*

Values marked with an asterisk (*) are outside the guaranteed accuracy range (reference value).

±6% RH*

±8% RH*

80 ±8% RH*
±6% RH

±5% RH

40 ±6% RH* ±3.5% RH
±5% RH

±3% RH

±5% RH

±6% RH ±5% RH

±4% RH

±6% RH* ±12% RH*

±6% RH

±10% RH* ±8% RH ±4% RH

±5% RH ±6% RH

±12% RH*

±8% RH*

±12% RH*

10 20 30 40 50 60 70 80

Temperature [°C]

* The measurement accuracy depends only on the sensor.

Hysteresis: ±1% RH (Added to the humidity measurement accuracy)

Response time

Approx. 300 seconds (Temperature: 90% response time for 0°C 60°C, 60°C 0°C [reference value]) (Humidity: 90% response time for 10% RH 80% RH, 80% RH 10% RH [reference value])

HIOKI LR8520B960-06

119

LR8520 Wireless Fungal Logger

Output
Alarm output

The built-in FET turns ON when the output is outside of the range (short circuit). Open drain output (Maximum rating: 30 V DC, 200 mA)

Function

Fungal index calculation

Calculate a fungal index from temperature and humidity (0 to 200). Predict fungal growth based on the integrated fungal index (5 levels).

Alarm

Displays [ALARM] when the value is outside of the setting range.

Lit:

The current measurement value is outside the range.

Blinking: There was a value that was outside the range but the

current value is in the range.

Scaling

Scales and displays a measurement value. (The lamp turns off if a unit other than the allowable display unit is set during scaling.)

Recording operation hold function

Automatically recovers records after the power is recovered if the power is shut off during recording. (The data during power shutdown will not be recorded.)

Erroneous operation prevention function

Displays a confirmation message when recording starts/stops, or the power is turned off. Whether a confirmation message is displayed can be selected.

Comment recording function

Records a comment in the title or each channel (up to 40 singlebyte characters) (number, English character, symbol).

Power saving function

Energy can be saved by turning ON/OFF the Bluetooth power. 1. Manual ON/OFF using the power key 2. Automatic ON/OFF according to the schedule setting
Energy saving can be set according to the date, day, or time (10 minutes to 12 hours).

Authentication function Authentication using a password (ON/OFF)

Free Run

ON/OFF selection ON : The measurement value is indicated every 1 second while
measurement is stopped. (the data is not saved in the memory) The measurement value is saved in the memory every recording interval and indicated every 1 second regardless of recording interval setting while measuring. (when the setting of recording interval is less than 1 second, the measurement value is indicated every recording interval) OFF : The measurement value which is at the time of a measurement stop is indicated while measurement is stopped. The measurement value is saved in the memory and indicated every recording interval while measuring.

120

HIOKI LR8520B960-06

LR8520 Wireless Fungal Logger

Power supply

Power supply AC adapter

Z2003 AC Adapter (12 V DC) Rated supply voltage: 100 V to 240 V AC (A voltage fluctuation of ±10% of the rated power voltage is taken into account.) Rated supply frequency: 50 Hz/60 Hz Anticipated transient overvoltage: 2,500 V

Battery

LR6 alkaline battery × 2

External

5 V to 13.5 V DC (can also be supplied from USB bus power,

power supply 5 V DC with a conversion cable)

Power consumption

Normal power consumption

Recording interval: 1 minute When the Z2003 AC Adapter or 12 V DC external power supply is used 0.2 VA (with Bluetooth ON) 0.05 VA (with Bluetooth OFF)

Maximum rated power

When the recording interval is 0.5 seconds during real-time measurement Z2003 AC Adapter: 4.5 VA (AC adapter included), 0.45 VA (instrument only) 13.5 V DC external power supply: 0.5 VA Batteries: 0.3 VA

Continuous operating time

Battery

Approx. 3.5 months (reference value at recording interval of 1 minute, Bluetooth OFF, 23°C) Approx. 3 months (reference value at recording interval of 1 second, Bluetooth OFF, 23°C) Approx. 20 days (reference value at recording interval of 1 second, Bluetooth ON, 23°C) Approx. 5 days (reference value at recording interval of 0.5 seconds during real-time measurement, 23°C) (When the recording interval is 2 second or later and the free run setting is on, the life is the same as for 1 second intervals.)

Accessories

See: p.2

Options

See: p.3

HIOKI LR8520B960-06

121

Z2010, Z2011 Humidity Sensor

5.2 Z2010, Z2011 Humidity Sensor

Basic specifications

Product warranty period

1 year

Guaranteed accuracy period

1 year

Sensor type

Temperature: Semi-conductor sensor Humidity: Capacitance humidity sensor

Supported instrument

LR8514 Wireless Humidity Logger LR8520 Wireless Fungal Logger

Operating environment

Indoors, Pollution Degree 2, altitude up to 2,000 m (6,562 ft.)

Operating temperature and humidity

Temperature: -40°C to 80°C (-40.0°F to 176.0°F) Humidity: 90% RH or less (non-condensation)

Storage temperature Temperature: -20°C to 60°C (-4.0°F to 140.0°F)

and humidity

Humidity: 80% RH or less (non-condensation)

Temperature and humidity for guaranteed accuracy

At temperature measurement Temperature: -40°C to 80°C (-40.0°F to 176.0°F)
(Only the operating temperature and humidity of the logger when Z2010 is used) Humidity: 80% RH or less (non-condensation) At humidity measurement Temperature: 10°C to 60°C (50.0°F to 140.0°F) Humidity: 10% RH to 90% RH or less (non-condensation)

Dimensions

Sensor:

Approx. 35W×12.5H×9D mm (1.38W×0.49H×0.35D)

Cable length (including the sensor):

Approx. 48 mm (1.89") (Z2010),

Approx. 1,530 mm (60.24") (Z2011)

Mass

Approx. 5 g (0.2 oz.) (Z2010), Approx. 37 g (1.3 oz.) (Z2011)

Dustproof and waterproof

None

Temperature measurement accuracy

±0.5°C (10°C to 60°C) If the temperature is outside of the range Add 0.015°C/°C (-40°C to 10°C) or 0.02°C/°C (60°C to 80°C).

122

HIOKI LR8520B960-06

Z2010, Z2011 Humidity Sensor

Humidity measurement accuracy

±3% RH (20°C to 30°C , 20% RH to 90% RH) See the figure below if the humidity is outside of the range.

Relative humidity [% RH]

100

±8% RH*

Values marked with an asterisk (*) are outside the guaranteed accuracy range (reference value).

±6% RH*

±8% RH*

80 ±8% RH*
±6% RH

±5% RH

40 ±6% RH* ±3.5% RH
±5% RH

±3% RH

±5% RH

±6% RH ±5% RH

±4% RH

±6% RH* ±12% RH*

±6% RH

±10% RH* ±8% RH ±4% RH

±5% RH ±6% RH

±12% RH*

±8% RH*

±12% RH*

10 20 30 40 50 60 70 80

Temperature [°C]

Response time

Hysteresis: ±1% RH (Added to the humidity measurement accuracy)
Approx. 300 seconds (Temperature: 90% response time for 0°C 60°C, 60°C 0°C [reference value]) (Humidity: 90% response time for 10% RH 80% RH, 80% RH 10% RH [reference value])

HIOKI LR8520B960-06

123

Z2010, Z2011 Humidity Sensor

124

HIOKI LR8520B960-06

6 Maintenance and Service

6.1 Repair, Inspection, and Cleaning

Replacement parts and service life
The characteristics of some parts that are used on this product may deteriorate due to long-term use. We recommend periodical replacement to use this instrument for many years. Contact your authorized Hioki distributor or reseller for parts replacement. The service life of parts varies depending on the usage environment and frequency. The period of the recommended replacement cycle is not guaranteed.

Part name Lithium battery

Recommended replacement cycle Approx. 5 years

Electrolytic capacitor

Approx. 10 years

Calibrations
IMPORTANT Periodic calibration is necessary in order to ensure that the instrument provides correct measurement results of the specified accuracy. The calibration frequency varies depending on the status of the instrument or installation environment. We recommend that the calibration frequency is determined in accordance with the status of the instrument or installation environment and that you request that calibration be performed periodically. Initializing of settings and upgrading to the latest software version may be carried out during repair and restoration. Please backup any important data before sending it for repair and calibration.
For LR8520 unit Only the Humidity Sensor, which affects the measurement accuracy, is subject to calibration. No calibration for LR8520 Wireless Fungal Logger is required because it has no measurement circuit that affects the accuracy.

HIOKI LR8520B960-06

125

Repair, Inspection, and Cleaning
If the instrument is not to be used for an extended period of time
CAUTION
To avoid corrosion from battery leakage and/or damage to the instrument, remove the batteries from the instrument if it is to be kept in storage for an extended period.
Precautions during shipment
CAUTION
· To avoid damaging the instrument, remove accessories and options from the instrument.
· Avoid any vibration or impact to prevent damage to the instrument during transportation and handling. Be especially careful regarding the impact by a fall.
· When shipping the instrument, use the original packing materials that were used when the instrument was delivered.
Cleaning · To clean the instrument, wipe it gently with a soft cloth moistened with water or mild
detergent. · Wipe the display gently with a soft, dry cloth.
IMPORTANT Never use solvents such as benzene, alcohol, acetone, ether, ketones, thinners or gasoline. Doing so may deform or discolor the instrument.

126

HIOKI LR8520B960-06

Troubleshooting

6.2 Troubleshooting

When a malfunction of the instrument is suspected, check "Before sending the instrument for repair" and then contact your authorized Hioki distributor or reseller.

Before sending the instrument for repair When the instrument operation does not seem normal, check the following items.

Symptom

Possible cause

Solution and reference

The measurement value does not appear.

When the number of recorded data is 0, the measurement value and maximum/ minimum/average value are not displayed.

Start measurement.

The measurement value is not correct.

Is the cable and/or sensor completely inserted?

Completely insert the cable and/or sensor. If the measurement is still not correct, the cable and/or sensor need to be repaired or inspected. Contact your authorized Hioki distributor or reseller.

The batteries die Manganese dioxide Use new LR6 alkaline batteries.

quickly.

batteries are used.

The keys do not work.

The instrument has Remove the AC adapter and batteries and then

an internal error or the turn on the instrument power.

keys have failed.

If the problem persists, the instrument needs to be

repaired or inspected.

Contact your authorized Hioki distributor or reseller.

The instrument cannot establish communications.

The instrument has an internal error or the communication module has failed.

Remove the AC adapter and batteries and then turn on the instrument power. If the problem persists, the instrument needs to be repaired or inspected. Contact your authorized Hioki distributor or reseller.

Nothing appears in the display.

· The power is OFF. · Hold down the power key to turn the power ON.

· The AC adapter is · Check that the AC adapter is connected correctly.

improperly attached.

· The AC adapter

· Check to see that the batteries are properly

is incorrectly

installed.

connected.

· The batteries are · Use new LR6 alkaline batteries.

exhausted.

If the problem persists, the instrument needs to be

repaired or inspected.

Contact your authorized Hioki distributor or reseller.

HIOKI LR8520B960-06

127

Troubleshooting

Symptom

Possible cause

Solution and reference

When the power The backup lithium is turned ON, the battery life has date and time expired. are significantly deviated from the correct values.

The replacement cycle for the backup lithium battery is 5 years. Contact your authorized Hioki distributor or reseller.

Measured data Recording has cannot be found. restarted since
measurement stop.

Be aware that data is deleted if recording is started accidentally after measurement stops.

· The wireless logger cannot be found.
· A connection to the wireless logger cannot be established.

Are you using the LR8410 to perform real-time measurement?
The Bluetooth module power is OFF ( is off or blinking).
The wireless logger cannot be searched for or connected if another terminal (LR8410, PC, or Android terminal) is connected ( is lit).
Windows® nonstandard Bluetooth stack is used.

Data cannot be collected with Wireless Logger Collector during real-time measurement by the LR8410.
Press the power key of the instrument and turn ON the Bluetooth module power.
Cut off the communications of the connected terminal and then search for or connect the wireless logger again.
Use Windows® standard Bluetooth stack or allocate virtual COM port manually. (p.43) When using a commercially available USB Bluetooth adapter, please uninstall the device driver of Bluetooth adapter accessory.

Bluetooth pairing

Notice of a pairing request is shown in a notification

information has been area of Windows® or Android terminal. As it is

lost.

directed, please redo a pairing.

Communication with all Bluetooth compatible instruments is not guaranteed.

Try other terminals.

128

HIOKI LR8520B960-06

Troubleshooting

Symptom

Possible cause

Solution and reference

Communications with the wireless logger cannot be established. An error occurs.

The settings cannot be sent or received or maintenance cannot be performed while the wireless logger is busy (during measurement or monitoring).

Stop measurement or monitoring and then try again.

As the security

Enter the correct password.

settings are enabled,

an authentication error

occurs.

HIOKI LR8520B960-06

129

Error Display

6.3 Error Display

When there is an error in the instrument, the error is displayed as follows. Instrument error display

Error display Err.1 Err.2 Err.3 Err.4 Err.5
Err.140 O.F. U.F.
BURN BATT LO
----

Meaning

Solution and reference

Adjustment data error An error has occurred in the internal adjustment data.

Repair or inspection is required. Contact your authorized Hioki distributor or reseller.

Serial number error An error has occurred in the internal memory.

Microcomputer operation error An error has occurred in the program ROM.

Bluetooth module error

· Disconnect the Z2003 Adapter and

An error has occurred in the

connect it again.

Bluetooth module.

· Remove the batteries and place new

Hardware error An error has occurred in the hardware.

LR6 alkaline batteries. · If the problem persists, the
instrument needs to be repaired or inspected. Contact your authorized

Backup battery error

Hioki distributor or reseller.

An error has occurred during clock

backup.

The measurement value is outside The measurement value cannot

of the measurement range or

be displayed as it is outside of the

display range.

measurement range or display range.

Check the input signal. (p.19)

A temperature and humidity

Completely insert the temperature and

sensor error has been detected. humidity sensor. (p.27)

Power supply error

· Remove the Z2003 AC Adapter and

The power voltage drops to the

connect the AC Adapter.

point where the instrument cannot · Remove the batteries and place new

operate properly.

LR6 alkaline batteries.

Not measured A measurement value cannot be displayed as measurement has not been performed.

Start measurement.

130

HIOKI LR8520B960-06

Disposal
6.4 Disposal
Backup lithium batteries are built into the instrument. When disposing of the instrument, remove the lithium batteries and handle and dispose of the instrument in accordance with local regulations.
CALIFORNIA, USA ONLY Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
WARNING
To avoid electric shocks, remove the power cord and measurement cables and then remove the lithium batteries.
Removing lithium batteries
Required items: 1 Phillips screwdriver (No. 2) and nippers
1 Remove the cables and power cord.
2 Remove the screw that secures the
bottom case on the instrument rear side and remove the battery cover.
3 Remove the batteries and screws (4).

Lithium battery

4 Remove the bottom case.

Remove the bottom case.

5 Remove the lithium batteries.
Pull up the lithium batteries from the printed
board and cut the + and - leads using the
nippers.

HIOKI LR8520B960-06

131

Disposal

132

HIOKI LR8520B960-06

Appendix

Recording interval and recording time

500,000 data can be recorded for each channel.

Recording interval 0.1 seconds 0.2 seconds 0.5 seconds 1 second 2 seconds 5 seconds 10 seconds 20 seconds 30 seconds 1 minutes
2 minutes to 1 hour

Recordable time 13 hours 53 minutes 20 seconds 1 day 3 hours 46 minutes 40 seconds 2 days 21 hours 26 minutes 40 seconds 5 days 18 hours 53 minutes 20 seconds 11 days 13 hours 46 minutes 40 seconds 28 days 22 hours 26 minutes 40 seconds 57 days 20 hours 53 minutes 20 seconds 115 days 17 hours 46 minutes 40 seconds 173 days 14 hours 40 minutes 00 second 347 days 5 hours 20 minutes 00 second 365 days or more

When continuous recording is set to ON (Endless), old data is overwritten until measurement is stopped. Latest 500,000 data are saved in the memory.

Target collection time

Time required to collect 500,000 data (reference)

Model LR8520

Time Approx. 12 minutes

(While measurement is stopped)

HIOKI LR8520B960-06

Appx.1

Initial setting list

Measurement
Channel Other settings

Item Recording Interval Continuous Recording Scheduled Record Start Scheduled Record Stop Alarm Composite Condition Hold Alarm Alarm Output Measurement Input Type
Range Scaling Power Save Prevent a Wrong Key Operation on the Body Start Backup Security Free Run

Settings 1 min ON (Endless) OFF OFF ON OR (Between channels) OFF ON ON Temperature/Humidity/Fungal Index/ Predicted fungal growth (fixed) 100°C/100% RH/200/10 (fixed) OFF OFF OFF
OFF OFF OFF

Handling Data

The saved data will include values listed in the below table on the following occasions: · When the waveform level significantly exceeded the measurable scope of each
range (+OVER, -OVER) · When the start backup setting resumed the measurement after a power failure
occurred during recording. (NO DATA) · When older data was replaced with newer data because the memory was full
(NO DATA) · When a humidity sensor malfunction was detected (BURN OUT)

Input type Temperature Humidity Fungal index Predicted fungal growth
Appx.2

Range 100°C 100% RH
200 10

+OVER 327.67

-OVER -327.68

HIOKI LR8520B960-06

NO DATA 327.65 3276.5 3276.5 3276.5

BURN OUT 327.66 3276.6 3276.6 3276.6

For customers who are using the LR8410 Wireless Logging Station
This instrument can be used on the LR8410 firmware version 1.30 or later. The firmware version for the LR8410 is displayed on the system screen.
The latest version can be downloaded from our website. For details on how to upgrade the software, see our website or check with your authorized Hioki distributor or reseller.

HIOKI LR8520B960-06

Appx.3

Using the LR8410 as a Unit
There are two ways. Real-time measurement using the LR8410

LR8410

(Line-of-sight 30 m) Real-time measurement using a Windows® PC
LR8410

Windows® PC (Logger Utility)

(Line-of-sight 30 m)

LAN/USB communications

Real-time Measurement Using the LR8410
1 Turn ON the power of the instrument and the LR8410. 2 Register the instrument as a unit using the LR8410 Quick Set function (Unit
Guide).

3 Set the measurement conditions using the Quick Set function (Config.
Guide) and send the conditions to the instrument.
4 Start measurement.
For details, refer to the LR8410 measurement guide.

Appx.4

HIOKI LR8520B960-06

Performing Real-time Measurement Using a Windows® PC
1 Register the instrument as a unit in the LR8410. (p.Appx.4) 2 Install Logger Utility on the Windows® PC.
Logger Utility
3 Start up Logger Utility.
The main screen is displayed when Logger Utility starts up. The main screen is the basic screen for Logger Utility.

4 Set the measurement conditions for the instrument. 5 Send the measurement conditions to the instrument. 6 Start or stop measurement.
For details, refer to the Logger Utility instruction manual on the provided CD.

HIOKI LR8520B960-06

Appx.5

Appx.6

HIOKI LR8520B960-06