Instructions for bkvibro models including: AC-1405, Velocity Sensor, AC-1405 Velocity Sensor, Sensor
Velocity Sensor VSI-101 - VSI-101
Betriebsanleitung AC-1405 DE Aderendhülsen ohne Isolierung Kabelschirm abgetrennt, Draht verzinnt L = Kabellänge HINWEIS: Diese Betriebsanleitung ist Teil des Produktes. Lesen Sie die Betriebsanleitung vor der Verwendung des Produktes sorgfältig durch und bewahren Sie die Anleitung für den zukünftigen Gebrauch auf. Anwendung Das vieradrige Anschlusskabel AC-1405 ist geeignet für den Anschluss von Sensoren und Transmittern mit vierpoligem M12-Stecker an ein Maschinenüberwachungssystem. Technische Daten · Steckerausführung · Kabellänge L · Aderzahl · Ader- querschnitt M12, 4-polig, weiblich, gerade 5,0 m; 10,0 m 4 4 x 0,34 mm² · Leiterwiderstand 5m · Schirm mit Überwurfmutter verbunden · Biegeradius min. 26 mm statisch min. 62 mm dynamisch Montage / Anschluss · Mantel · Außen- durchmesser · Temperaturbereich · Lagerungstemperaturbereich · Steckzyklen · IP-Schutzart nach EN 60529 PUR, black 5,1 mm -30 °C .. +90 °C -40 °C .. +90 °C min. 100 IP65, IP67, IP68 HINWEIS: Prüfen Sie vor jeder Inbetriebnahme die Kabel auf Funktion und Beschädigung. Tauschen Sie beschädigte Kabel sofort aus. Montieren Sie das Anschlusskabel, in dem Sie den korrekt ausgerichteten Stecker auf den Sensor setzen. Ziehen Sie die Überwürfmutter an. Drücken Sie den Stecker in Richtung Sensor nach. Wiederholen Sie diesen Vorgang so oft, bis sich der Stecker nicht mehr in die Buchse nachdrücken lässt. Drehen Sie die Überwurfmutter abschließend fest. Zur Demontage gehen Sie in umgekehrter Reihenfolge vor. Bestellcode AC-1405/xxxx/x Brüel & Kjær Vibro GmbH Leydheckerstraße 10 D-64293 Darmstadt Abb 1) Pinbelegung des M12 Kabelsteckers 0050 = 5 m 0100 = 10 m 1 = mit Stahlschutzschlauch Tel.: +49 6151 428-1400 Fax : +49 6151 428-1401 E-Mail : info@bkvibro.com UNRESTRICTED DOCUMENT AC-1405 / C108242001 / V01 © Brüel & Kjær Vibro 08/2022 / Seite 1 von 2 Instruction AC-1405 EN ferule without isolation Cable screen flush cutted, additional wire tinned L = Cable length NOTE : This manual is a part of the product. Read the manual carefully before using the product and keep it safe and easily accessible for future use. Application The four-core connection cable AC-1405 is suitable for the connection of sensors and transmitters with 4-pole M12-plug to a machine monitoring system. Technical data · Plug design: M12, 4-pole, female, straight plug · Cable length L 5,0 m; 10,0 m · Number of conductors 4 · Conductor cross section 4 x 0,34 mm² · Conductor resistance 5m · Shield connected to union nut · Bending radius · Outer jacket · Outer diameter · Operating temperature range · Storage temperature range · Mating cycles IP-protection acc. to EN 60529 min. 26 mm statisch min. 62 mm dynamisch PUR, black 5,1 mm -30 °C .. +90 °C -40 °C .. +90 °C min. 100 IP65, IP67, IP68 Connection NOTE: Check for function and damage to the cable prior to each commissioning. Replace damaged cables immediately. Install the connecting cable by putting the correctly aligned plug onto the sensor. Tighten the union nut. Press the plug further towards the sensor. Repeat this process as often as necessary until the plug cannot be pressed any further into the socket. Then tighten the union nut. For deinstallation, proceed in the reverse order. Order code: AC-1405/xxxx/x Fig 1) Pin configuration of the M12-cable connector 0050 = 5 m 0100 = 10 m 1 = with steel protective conduit Brüel & Kjær Vibro GmbH Leydheckerstrasse 10 D-64293 Darmstadt Phone: +49 6151 428-1400 Fax : +49 6151 428-1401 E-Mail : info@bkvibro.com AC-1405 / C108242001/ V01 © Brüel & Kjær Vibro 08/2022 / Page 2 of 2Simone Stern Adobe PDF Library 22.1.149