Instructions for DELL models including: S2319HS, 23 inch Monitor, S2319HS 23 inch Monitor, Teardown
QSG, accessories including. DP cable, power cable, USB cable, CD&user's manual, stand and base from the carton from the carton.(Note: It depends on whether ...
dl.dell.com - /manuals/all-products/esuprt electronics accessories/esuprt electronics accessories monitor/esuprt monitor s series/
File Info : application/pdf, 6 Pages, 2.82MB
DocumentDocument1 DELL S2319HS Go to contents page 1. Disassembly Procedures: S1 Open the Pizza carton with a proper tool. Use a Philips-head screwdriver to remove four S4 screws for unlocking mechanisms. (No.1~4 screw size=M4x10; Torque=12±0.5kgfxcm) 2 3 4 1 Take out all of the accessories including QSG, DP cable, power cable, USB cable, CD&user's manual, S2 stand and base from the carton from the carton.(Note: It depends on whether users returning the accessories) QSG power cable DP cable USB cable Wedge your fingers between the rear cover and the middle bezel on the corners of the top side of the S5 monitor to release the rear cover, then use one hand to press the middle bezel, the other hand to pull up carefully the rear cover in order of arrow preference for unlocking mechanisms of rear cover.. 3 4 2 1 base stand user's manual Take out of the Paper-top and monitor from the S3 carton, then take out the monitor from the EPE bag and put the LCD monitor on a protective cushion. Lift the rear cover up carefully. Disconnect the USB S6 FFC cable from the connector of the interface board, and then remove the rear cover. Use a Philips-head screwdriver to remove one screw S7 for unlocking the USB board unit, then release the USB board unit and put it aside. (No.1 screw size=M3x6, Torque=4±0.5kgfxcm) DELL S2319HS 2 Go to contents page S11 Use a Philips-head screwdriver to remove 2pcs screws for unlocking the bracket with the panel. Push the earing-lock, and disconnect the LVDS cable from the connector of LCD panel module. (No.1~2 screw size=M3x2.8, Torque=2~3kgfxcm) 1 S8 Tear off two pieces of the aluminium foils for unfixing the bracket chassis base. aluminum foil aluminum foil Unplug the panel power cable from the connector of the panel module, then release the function by S9 tearing the tapes on the back of the cable, and then release the cable from the hooks of the middle bezel. 2 1 S12 Use a Philips-head screwdriver to remove 13pcs screws for unlocking the middle bezel with the assembled unit. (No.1~11 screw size=M3x4, Torque=3~4kgfxcm; No.12~13 screw size=M1.6x1.7, Torque=0.6~1kgfxcm) 2 4 8 6 1 53 9 7 10 12 11 13 S13 Take away the middle bezel, and put it on a fixture, then use a Philips-head screwdriver to remove 3pcs screws for unlocking the function key board with the middle bezel . S10 Use a proper tool to release the function key cable from the connector, then pull the function key cable high for releasing the function key cable. 3 2 1 3 DELL S2319HS Go to contents page S17 Remove the Mylar from the hooks of the bracket. Use a Philips-head screwdriver to remove six screws for unlocking the circuit board, release all the cables from the hooks. (No.1~5 screw size=M3x7.5, Torque=6±0.5kgfxcm; No. 6 screw size=M4x8, Torque=6±0.5kgfxcm) S14 Lift up the panel module for releasing the front bezel away from the panel module. S15 Take away the bracket chassis module and then put the bracket chassis module on a protective cushion. 3 4 2 5 6 1 S18 Remove the interface board and power board from the bracket chassis module carefully, and disconnect all the cables. S16 Use a Hex-head screwdriver to remove two screws for unlocking the D-Sub connector. (No.1~2 screws size=M3x8, Torque=6±0.5kgfxcm) Use a Philips-head screwdriver to remove two screws for unlocking the AC power outlet. ( No.3~4 screw size=M3x8, Torque=6~7kgfxcm) 2 1 4 3 S1 Remove electrolyte capacitors (red mark) from printed circuit boards DELL S2319HS 4 S1-1 Cut the glue between bulk cap. and PCB with a knife S1-2 Ensure cutting path within the glue, don't touch bulk cap. or PCB S1-3 Cut into the bottom of bulk cap. and pull it up carefully DELL S2319HS 5 S1-4 Take out bulk cap. pin solder with soldering iron and absorber S1-5 Lift the bulk cap. up and away from the PCB DELL S2319HS 6 . Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC. Capacitors / condensers (containing PCB/PCT) Mercury containing components Batteries Printed circuit boards (with a surface greater than 10 square cm) Component contain toner, ink and liquids Plastic containing BFR Component and waste contain asbestos CRT Component contain CFC, HCFC, HFC and HC Gas discharge lamps LCD display > 100 cm2 External electric cable Component contain refractory ceramic fibers Component contain radio-active substances Electrolyte capacitors (height > 25mm, diameter > 25mm) No used No used No used Product has printed circuit boards (with a surface greater than 10 square cm) No used No used No used No used No used No used Product has an LCD greater than 100 cm2 Product has external cables No used No used Product has electrolyte capacitors (height > 25mm, diameter > 25mm) . Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: - Screwdriver (Phillip head) #1 - Screwdriver (Phillip head) #2 - Penknife - Soldering iron and absorberCorel PDF Engine Version 14.0.0.653; modified using iTextSharp 5.1.3 (c) 1T3XT BVBA