TAKSTAR XR-1016FX Analog Mixer User Manual

User Manual for TAKSTAR models including: XR-1016FX Analog Mixer, XR-1016FX, Analog Mixer, Mixer

XR-1016FX XR-1824FX 得胜调音台说明书 20220923 XR-1016FX XR-1824FX 得胜调音台说明书 20220923

scb036

点击下载

【得胜官网 XR-1824FX （2023款）模拟调音台】音响系统 - 产品信息

【得胜官网 XR-1016FX（2023款）模拟调音台】音响系统 - 产品信息

File Info : application/pdf, 24 Pages, 13.55MB

XR-1016FX 模拟调音台说明书

XR-1016FX / XR-1824FX
ANALOG MIXER
USER MANUAL

XR-1016FX/XR-1824FX

XR-1016FX/XR-1824FX
4006828333

· · DSP16 · 8/16XLR46 · L/R · USB-A MP3USB-B · +48V · 3 · · 60

.....................................................................................................................................................1 .....................................................................................................................................................1 .....................................................................................................................................................1
1

XR-1016FX/XR-1824FX

: 8/16XLR : 20 Hz - 20 kHz, +/-1 dB THD+N) <0.003% at +0 dB, 20 Hz-20 kHz
: +20 dBu : 14k : +48 V : 80 Hz

: 8/16TRS : 20 Hz - 20 kHz, +/- 1dB (THD+N): <0.003% at +0 dB, 20 Hz-20 kHz : 20 dB to -30 dB
: 21 k

: 4 TRS2 RCA : 20 Hz - 20 kHz, +/- 1 dB (THD+N): <0.003% at +0 dB, 20 Hz-20 kHz : 20 dB to -30 dB : 15 k

EQ
: +/-15 dB @ 10 kHz Shelving : +/-15 dB @ Freq.sel. from 100Hz to 8kHz
-Bell : +/-15 dB @ 100 Hz Shelving

DSP : 20/27 bit digital signal A/D D/A : 24 bit : 4 algorithms: reverb, chorus, delay,
flanger - 16 presets
: TS jack (for effect return mute and unmute)

EQ
: +/-15 dB @ 10 kHz Shelving : +/-15 dB @ 1,250 kHz Bell : +/-15 dB @ 100 Hz Shelving

: 1 XLR1 6.3mm TRS : +28 dBu : 4 TRS : +28 dBu 1,2: 2 TRS : +28 dBu 3,4: 2 TRS : +28 dBu : 1 TRS : 1 TRS

: 100 V - 240 V AC, 50-60 Hz : 30 W

XR-1016FX 468*440*95mm XR-1824FX 680*450*95mm

: 6.6Kg : 9.3Kg

XR-1016FX/XR-1824FX
XR-1016FX
XR-1824FX
1 220V
2
3 USB-B USB
4 USB-A U
5 AUX 1 - 4 AUX 1/4 TRS AUX Level (10)
6 BUS1-4 1/4" TRS
3

XR-1016FX/XR-1824FX

1 MIC IN

XLR o dB -50 dB MIC/LINE

80 Hz 80 Hz

2 LINE IN(1/4)
1/4"( TRS ) 2

3 GAIN

MICLINE

0-50dBLINE-20--+30dB;

PEAK

4
4 LOW CUT 80Hz 5 6

5 COMP

4:1

6 HIGH EQ

(10 kHz±15dB)

7 MID EQ 1250 Hz, +/-15 dB

8 MID FREQ

Mid EQ100 Hz

8kHz

9 LOW EQ (100 Hz ±15 dB), 11

10 AUX1-4

XR-1016FX4 AUX1 AUX2 PRE AUX3

POST PRE AUX3 PRE/POST ( [32] ) FX/AUX4

FX/AUX4 PRO DSP FX FX/AUX4

AUX4 OUTPUT

11 PAN

/1/2

(17)1/21

18
12 MUTE SWITCH

solo

XR-1016FX/XR-1824FX

13 MUTE LED LED,

14 PEAK LED

LED

EQ +15 dBu

(

EQ5dB EQ LED

15 PFL SWITCH

PFLCTRL ROOM OUTPUT

16 MAIN SWITCH

MAIN MIX

17 GROUP 1-4 SWITCH BUS 1/2BUS3/4 1/2, 3/4

18 CHANNEL FADER -+10dB,0dB

19 LINE/Hi-Z DI Box 1/4" TRS 1/4" TRS DI DI
19

20 RCA RCA L/R mp3CD

1/4" TRS 1/4" TS

22 -20 --+30dB, 0PFL 3 LED

23 USB-B USB-B

IN USB-B

XR-1016FX/XR-1824FX

24 FX

FOOT SWITCH 1/4"TRS

25 1/4" TRS PHONES

26 / /21/4" TRS Z 2XLR 1/4" Tip, Ring, Sleeve (TRS) Tip, Sleeve (TS) (39) 2

27 1/4"

28 (XR-1824FX2) XLR +48 VDC XLR

29 AUX1-3 FX AUX1-3
30 AUX3 / AUX3/FX

31 AUX1-4 MASTER AUX1-4 PFLCTRL ROOM OUTPUT [27] )PHONES OUTPUT ([25] )

32 12 LED "CLIP"

33 PFL ACTIVE LED PFL LED

34 CTRL ROOM CTRL ROOM PFL PFL CTRLROOM

35 (-)

"TO CTRL ROOM"

L/RBUSSES

BUS1/2BUS3/4

26
27 28
8 32

33 34

XR-1016FX/XR-1824FX

37 DSP PFL CTRL ROOMPHONES OUTPUTMAIN 1/23/4 BUS1/2BUS3/4

38 BUS 1/2, BUS 3/4 BUS 1/2 BUS 3/4 BUS 1/2 BUS 3/4 BUS OUTPUTS MUTE BUS BUS MAINBUS MAIN MIXPFL CTRL ROOMOUTPUT BUS PHONES OUTPUT
37
39 MAIN MIX MAIN MIX
40

41 / 42 43 BT

43 44 45

44 UUSB-A 45 UREC

46 (1-16)MODE

47 (1-16)

a. BT () BT 2 Mixer BT// /2 (MODE) 3
b. USB () USB-AU(MODE)U USB/// U USB-AU(MODE)U

XR-1016FX/XR-1824FX

c. REC () USB-AUUUSB (MODE)3REC (MODE)3REC 3(MODE)REC (MODE)3
d. REC () USBREC ///U (MODE)33 MODE

DSP
XR-1016FX, XR-1824FX 16 PRO DSP FX 16

01. SMALL HALL

05. THIN PLATE

09. ANALOG DELAY

13. PHASER

02. LARGE HALL

06. PLATE

10. CHORUS VERB

14. GATED REVERB

03. SMALL ROOM

07. SPRING REVERB

11. STEREO CHORUS

15. FLANGER REVERB

04. BRIGHT ROOM

08. MULTITAP DELAY

12. FLANGER

16. VOCAL ECHO

XR-1016FX/XR-1824FX
XR-1016FX
9

X RXR--1100161FX6/XFR-1X82/4XFXR-1824 FX

1. 2. 3. 4. 5. 6.
11

XR-1016FX/XR-1824FX
XR-1824FX
10

XR-1016FX/XR-1824FX ANALOG MIXER
PREFACE
Dear Customer, Thank you for purchasing Takstar XR-1016FX/XR-1824FX Analog Mixer. In order to better understand and use the product, please read this manual carefully. If you have any questions or suggestions, please contact our local dealer.
FEATURES
· Robust metal housing · Professional DSP effector with 16 effects available · 8/16CH XLR mic inputs, 4CH bus outputs, 6CH with built-in compressor; separate stereo pan
control on each channel · Two stereo channels capable of direct routing to L/R · Bluetooth & USB-A MP3 playback, stereo USB-B audio input & output · Low-noise preamp + 48V phantom power · 3-band equalizer on each channel for treble/mid-range/bass adjustment · Studio quality headphone output · 60mm high precision faders
APPLICATIONS
Commercial performances, large gatherings, outdoors
PACKING LIST
Analog Mixer..............................................................................................................................................1 User Manual...............................................................................................................................................1 Power Cord................................................................................................................................................1
12

XR-1016FX/XR-1824FX ANALOG MIXER

SPECIFICATIONS
MONO INPUT
MIC IN: 8/16CH Bal XLR Frequency Response: 20 Hz - 20 kHz, +/-1 dB Distortion (THD+N): <0.003% at +0 dB, 20 Hz-20 kHz Sensitivity: 0 dB to -50 dB Max Input Level: +20 dBu MIC IN Impedance: 14 k, unbal Phantom Power: +48V Low Cut: 80 Hz

LINE IN: 8/16CH Bal TRS Frequency Response: 20 Hz - 20 kHz, +/-1 dB
Distortion (THD+N): <0.003% at +0 dB, 20 Hz20 kHz
Sensitivity: 20 dB to -30 dB Max Input Level: +40 dBu LINE IN Impedance: 21 k, unbal

STEREO INPUT
LINE IN: 4 pairs of Bal TRS + 2 pairs of Unbal RCA Frequency Response: 20 Hz - 20 kHz, +/-1 dB Distortion (THD+N): <0.003% at +0 dB, 20 Hz-20 kHz Sensitivity: 20 dB to -30 dB LINE IN Impedance: 15 k, unbal

MONO EQ
HIGH: +/-15 dB @ 10 kHz Shelving MID: +/-15 dB @ Freq.sel. from 100Hz to 8kHz
-Bell LOW: +/-15 dB @ 100 Hz Shelving

DSP
DSP: 20/27 bit digital signal A/D & D/A Converter: 24 bit FX Type: 4 algorithms: reverb, chorus, delay,
flanger - 16 presets
Foot Switch: TS jack (for effect return mute and unmute)

STEREO EQ
HIGH: +/-15 dB @ 10 kHz Shelving MID: +/-15 dB @ 1,250 kHz Bell LOW: +/-15 dB @ 100 Hz Shelving

OUTPUT
MAIN OUTPUT: 1 pair of XLR + 1 pair of 6.3mm TRS MAIN Max Output Level: +28 dBu AUX OUTPUT: 4 TRS AUX Max Output Level: +28 dBu STEREO GROUP 1/2 OUTPUT: 2 TRS GROUP Max Output Level: +28 dBu STEREO GROUP 3/4 OUTPUT: 2 TRS GROUP Max Output Level: +28 dBu Monitor Output: 1 pair of TRS Stereo Headphone Output: 1 Stereo TRS

POWER SUPPLY
Main Input Voltage: 100 V - 240 V AC, 50-60 Hz Power Consumption: 30W

XR-1016FX Dimensions: 468*440*95 mm; XR-1824FX Dimensions: 680*450*95 mm;

Weight: 6.6 kg Weight: 9.3 kg

XR-1016FX/XR-1824FX ANALOG MIXER
DESCRIPTIONS XR-1016FX REAR PANEL
XR-1824FX REAR PANEL
1 AC INPUT Connect the power cord to this socket and properly connect it to a 220V grounded AC power source.
2 POWER SWITCH Turns the mixer power on or off.
3 USB-B CONNECTOR Connect a computer to this port via a UBS cable for stereo recording and playback of audio signals.
4 USB-A STORAGE CONNECTOR Connect a USB flash drive for music playback and recording.
5 AUX OUTPUTS 1 4 These AUX outputs feature 1/4'' TRS balanced jacks and provide signal from auxiliary outputs. The output level is controlled by the AUX Level control (10).
6 BUS OUTPUTS 1 4 These BUS outputs feature 1/4'' TRS balanced jacks and provide signal from group outputs. The output level is controlled by the BUS Level fader.
14

XR-1016FX/XR-1824FX ANALOG MIXER

MONO INPUT

1 MIC IN

This XLR balanced mic preamp input supports sources with a gain range of 0 dB to -50 dB.

All MIC/LINE inputs feature an 80 Hz high pass filter, which can be enabled to reduce low

frequency pops, bumping and rattling noise when using a mic for vocals.

2 LINE IN (1/4)

These jacks are 1/4" balanced (TRS) high impedance inputs. The cores are positive and used for unbalanced inputs. MIC IN and LINE IN should not be used at the same time.

3 GAIN

May refer to MIC GAIN or LINE GAIN subject to input source. Using MIC IN, Gain Range:

0~50dB; Using LINE IN, Gain Range: -20~+30dB. Preferably set to a level where PEAK LED

only flashes occasionally, so to prevent distortion.

4 LOW CUT

An 80Hz low cut filter toggle. Enable it to cut off unwanted low frequency noise

(e.g., operating noise, stage noise, air noise) to improve clarity. These unwanted energy 5

could drain power from your audio system.

6
5 COMP

Turning this knob clockwise lowers the compressor threshold, increasing the amount of compression. The compression ratio is within 4:1 and varies with the signal level and

the amount of compression. This is useful for controlling peak levels from live sources,

and is designed to subtly tame the level of live vocals without noticeable artifacts.

6 HIGH EQ

This smooth-tilt tone control adjusts treble frequency levels (±15dB at 10 kHz), reducing

noise or boosting brightness.

7 MID EQ The IF control is set to 1250 Hz, with a gain of +/-15 dB and a bell curve.
10
8 MID FREQ This control knob determines the center frequency of the MID EQ control. The center frequency of the bandpass filter can be set between 100 Hz and 8kHz.

9 LOW EQ This smooth-tilt tone control adjusts the bass frequency level (±15 dB at 100 Hz), adding 11 depth to thin sounds or clarity to overly thick sounds.

10 AUX1-4

Each channel of the XR-1016FX mixer provides 4 aux sends; AUX1 and AUX2 are PRE fader

sends. AUX3 is a POST or PRE fader send, depending on the position of the AUX3 PRE/POST

button (32). FX/AUX4 send is always post-fader. FX/AUX4 is sent to the internal PRO DSP FX

board. Signals in FX/AUX4 send are also routed to the AUX4 OUTPUT jack on the rear panel.

11 PAN

This control determines the signal position of the assigned L/R channel and group 1/2 bus.

Turning the knob counterclockwise increases the amount of signal sent to the left channel

and odd group; while turning it clockwise increases the amount of signal sent to the right

channel and even group.

For example, when the GROUP SWITCH (17) is in the 1/2 position, turning the knob

counter-clockwise will increase the amount of signal sent to Group 1, and turning it

clockwise will increase the amount sent to Group 2. Equal amount is sent to each group if

rotated to the middle.

XR-1016FX/XR-1824FX ANALOG MIXER

12 MUTE SWITCH

Pressing this switch will mute the signal sent to the main mix, aux sends, and FX effects. The mute switch does not affect the signal sent to the solo system.

13 MUTE LED

The mute button is equipped with a red LED that lights up when the channel is muted.

15
14 PEAK LED

This LED usually indicates that the channel signal level is approaching clipping (distortion),

but it also lights up when muted. Because the peak indicator circuit monitors the signal

after gain, EQ and master level, peaks can be caused by high settings of any of these controls.

It lights up upon a static signal (test sound) of +15 dBu, which corresponds to the audible

peak of a highly dynamic signal (i.e. a piano). When lit, there is about 5dB of headroom

remaining, and the gain and EQ boost should be reduced. Under optimal settings of input

gain and EQ, LED will only flash briefly at the loudest peak.

15 PFL SWITCH This PFL button allows monitoring of the signal on this channel through a speaker connected to the CTRL ROOM OUTPUT or a headphone connected to the PHONES OUTPUT.

16 MAIN SWITCH This button allows signals to be routed individually to the MAIN MIX.

17 GROUP 1-4 SWITCH The BUS1/2, BUS3/4 buttons allow the signal to be routed to the stereo BUS 1/2, 3/4 respectively. 19
18 CHANNEL FADER Used to adjust the signal level of the channel sent to the main output; control range is - to +10dB, the optimal position is 0dB.

19 LINE/Hi-Z SWITCH To connect a guitar directly to the mixer without using a DI Box, press this switch down first; then connect the guitar's output to the channel's 1/4" TRS input. This helps to match the directly connected input impedance and preserve high frequency fidelity. The channel's 1/4" TRS input will become a line input, just like any other mono line input. To use guitars or other instruments on other channels, you'll need to use an external DI box first. Without the DI box or if this switch is not pressed the guitar may sound dull and muddy.

STEREO INPUT

20 STEREO INPUTS (RCA) RCA L/R line input which accepts signal from MP3 or CD player.

21 STEREO INPUTS

1/4'' TRS balanced or 1/4'' TS unbalanced line inputs. If you are

connecting a mono source, use the left (mono) input and the mono

signal will appear on both sides of the main mix.

22 STEREO GAIN

This control establishes the nominal operating level of the channel.

The the

sinigpnuatlg-taoi-nncoaisnebreataiod,juthsteegdaiinnashwoidueldrabnegseet(-t2o0a--n+a3p0pdrBo)p. Trioatme alexvimel.ize3

To do so, set the channel fader to 0, then press the PFL switch and

observe the LEVEL LED. If the CLIP LED glows and stays red, you need to

reduce the gain.

23 LINE IN / USB-B IN SWITCH When this switch is not pressed, the input signal of this channel is provided by line input; or when pressed, provided by USB-B.
16

IN USB-B

XR-1016FX/XR-1824FX ANALOG MIXER

PANEL

24 FOOT SWITCH

This 1/4" TRS connector is where the foot switch is connected. The

internal effect can be turned on and off through the foot switch. If the

internal effect channel has been muted, the foot switch will not work.

25 PHONES OUTPUT

This 1/4" TRS connector provides stereo headphone output. The

output volume of this channel is controlled by the PHONES volume

control knob.

26 L/R MAIN OUTPUT There are two 1/4'' TRS balanced jacks and two balanced XLR outputs for Left/Right outputs. 1/4" output can be connected with Tip, Ring, Sleeve (TRS) balanced or Tip, Sleeve (TS) unbalanced connector. Its output level is controlled by MAIN FADER (39). Both XLR and TRS outputs can be used at the same time.

27 CTRL ROOM OUTPUT These 1/4" jacks are usually connected to the input amplifier or headphone amplifier in the control room.

28 PHANTOM POWER (two on XR-1824FX) This switch applies +48VDC to the XLR input connector to power mics

that require phantom power. If enabled, do not connect unbalanced dynamic mics or other XLR input devices that cannot handle this voltage.

29 FX TO AUX 1-3

This allows routing of signal in the FX return channel to AUX1-3 send.

30 AUX3 PRE/POST This button sets whether the AUX3/FX signal is pre-fader or post-fader.

31 AUX 1-4 MASTER These potentiometers control the AUX1-4 master level. When PFL button is pressed, the signal present on the respective individual aux output can be monitored through the speaker connected to the CTRL ROOM OUTPUT (27) or the headphones connected to the PHONES OUTPUT (25).

32 LEVEL LED This 12-LED level meter helps to control the main mix output level. Keep the output level below the "CLIP" LED to avoid signal overload and distortion.

33 PFL ACTIVE LED This LED illuminates when one or more of the PFL buttons are pressed.

34 CTRL ROOM VOLUME This is the level control of signal routed to the CTRL ROOM OUTPUT. During regular use, the main channel mix signal is routed to this output; when one or more PFL buttons are pressed, the PFL bus signal is routed to CTRL ROOM OUTPUT and PHONES OUTPUT.

35 PHONES VOLUME

This knob controls the level of the headphone output. Set the

headphone volume level to the minimum (-) before connecting

and wearing headphones to avoid hearing damage.

26
27 28
8 32

33 34

XR-1016FX/XR-1824FX ANALOG MIXER

36 MONITOR SETTINGS There are two buttons for monitoring settings. For the upper button: when not pressed, it monitors the audio from MAIN L/R; when pressed, it monitors audio from BUSSES. For the lower button: when not pressed, it monitors audio from BUS 1/2; when pressed, it monitors audio from BUS 3/4.

37 FX FADER This fader controls the signal level from the internal DSP effector. The mute button, when pressed, disables signal flow to the output bus or main mix. The PFL button allows the current channel's signal to be monitored by CTRL ROOM OUTPUT and PHONES OUTPUT. The MAIN button allows the effect signal to be sent to the main channel for mixing. The 1/2, 3/4 buttons allow the effect signal to be sent to the stereo busses BUS 1/2 or BUS 3/4.

38 BUS 1/2, BUS 3/4 FADER Faders BUS1/2 and BUS3/4 control the level of the stereo bus outputs. 37

BUS 1/2 and BUS 3/4 can be fed by each input channel to create stereo audio groups routed to the physical

BUS OUTPUTS. When the MUTE button is pressed, signal flow to the BUS output or main mix is disabled. The

MAIN button next to the BUS fader routes the BUS to the MAIN MIX. When the PFL button is pressed, the signal

present in the BUS can be monitored through speaker connected to CTRL ROOM OUTPUT or headphones

connected to PHONES OUTPUT.

39 MAIN FADER This fader controls the level of the MAIN MIX.

40 PREVIOUS TRACK 41 PAUSE/PLAY 42 NEXT TRACK

43 44 45

43 BLUETOOTH (BT) MODE LED 44 USB-A PLAYBACK MODE LED

45 USB REC MODE LED

46 EFFECTS SELECTION (1-16) KNOB & MODE SELECTION BUTTON

47 EFFECT STATUS (1-16) DISPLAY

OPERATIONS
a. BT MODE (see picture on the right) After power on, the BT indicator will flash for 2 minutes, awaiting Bluetooth connection. Search for "Mixer BT" on your Bluetooth device and connect. Once paired successful, the BT indicator will stay lit. You can then manually play media inside your device using PAUSE/PLAY/PREVIOUS TRACK/NEXT TRACK. If without Bluetooth connection within 2 minutes, the Bluetooth function automatically shuts down and the BT indicator turns off. To re-try Bluetooth connection, press and hold the MODE button for 3 seconds to activate Bluetooth pairing and establish connection.

b. USB MODE (see picture on the right)

When a USB drive is inserted via USB-A port, press the MODE button to switch to

USB playback mode. In this case, the USB indicator will light up, and you can play

media inside your USB drive using PAUSE/PLAY/PREVIOUS TRACK/NEXT TRACK.

Note: You cannot switch to USB playback mode by pressing the MODE button if no

USB drive is inserted via USB-A.

XR-1016FX/XR-1824FX ANALOG MIXER

c. REC MODE (see picture on the right) While a USB drive is inserted via USB-A and mixer under USB playback mode (i.e., green USB indicator glows), press and hold MODE button for 3 seconds to enter REC mode. In this case, the REC indicator flashes red while recording normally. Press and hold MODE button for 3 seconds again to pause recording (REC indicator glows solid red). Again, press and hold MODE button for 3 seconds to exit REC mode and start playback of the recorded file.
d. REC PLAYBACK MODE (see picture on the right) While playing the recording file, the USB green light and the REC red light will be on at the same time, and you can control the playback using PAUSE/PLAY/PREVIOUS TRACK/NEXT TRACK. audio file. Press and hold the MODE button again for 3 seconds to continue recording. During the recording process, press and hold the MODE button for 3 seconds to pause recording. While paused, press the MODE button once to return to Bluetooth mode, and start new operation or selection.

DSP Effector
Both XR-1016FX and XR-1824FX are equipped with an internal PRO DSP FX board with 16 FX presets. Rotate the EFFECTS KNOB to select among the 16 sound effects:

01. SMALL HALL 02. LARGE HALL 03. SMALL ROOM 04. BRIGHT ROOM

05. THIN PLATE 06. PLATE 07. SPRING REVERB 08. MULTITAP DELAY

09. ANALOG DELAY 10. CHORUS VERB 11. STEREO CHORUS 12. FLANGER

13. PHASER 14. GATED REVERB 15. FLANGER REVERB 16. VOCAL ECHO

Enrich your audio with any of the above preset effects.

PLUG PINOUT DIAGRAM
1/4'' Balanced TRS Mono Wiring
Tip Ring Sleeve
Tip Ring Sleeve

Sleeve = Ground/Shield Tip = Hot Ring = Cold

Ring Sleeve Sleeve Ring Tip
Tip Ring Tip Sleeve

1/4'' Unbalanced TS Mono Wiring
Tip Sleeve

Tip

Sleeve

Sleeve = Ground/Shield Tip = Hot

Sleeve

Sleeve Tip

Tip Tip
Sleeve Shield

XLR Connector (Female) XLR Connector (Male)

XLR Connector
Bal XLR Wiring: 1 = Shield (Ground) 2 = Positive (+/Hot) 3 = Negative (-/Cold)

Cold Hot

Shield Cold Hot

XR-1016FX/XR-1824FX ANALOG MIXER
XR-1016FX BLOCK DIAGRAM
20

XR-1016FX/XR-1824FX ANALOG MIXER
XR-1824FX BLOCK DIAGRAM
21

X RXR--1100161FX6/XFRX-18/2X4FRX A-N1A8LO2G4MIFXEXR
CAUTIONS
To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and injury or property loss due to improper use, please read and observe the following items before use: 1. Please check if the power of the connected equipment matches with that of this product before
operation. Adjust the volume to proper level during operation. Do not operate at over-power or high-volume level for extended time to avoid product malfunction or hearing impairment. 2. If there is any abnormality during use (e.g., smoke, strange odor), please kill the power switch and unplug from power source, then send the product to the dealer for repair. 3. Keep this product and its accessories in a dry and ventilated area. Do not store in a humid or dusty area for extended time. Keep away from fire, rain, liquid intrusion, bumping, throwing, vibrating, or from blocking any ventilation openings, to prevent malfunction. 4. The product must, when installed on walls or ceilings, be fixed firmly in place at adequate strength to prevent from falling. 5. Please abide by safety rules during operation. Do not use the product in places prohibited by laws or regulations to avoid accident. 6. Do not disassemble or repair the product by yourself to avoid injury. If you have any questions or require any services, please contact our local dealer.
22

Corel PDF Engine Version 14.0.0.701