User Manual for RODSUMWIRELESS models including: AC-BLE-T110T, Aroco Wireless Beacon with Vibration Detection, Aroco Wireless Beacon, Wireless Beacon, AC-BLE-T110T, Beacon
| Rodsum Wireless
File Info : application/pdf, 22 Pages, 6.78MB
DocumentDocumentAroco AC-BLE-T110T Wireless Beacon User Manual Revision: v1.0 Updated: 25 May 2022 Rodsum Wireless Limited www.rodsum.com Page 1 of 22 Change Number Revision Description First version Amendment History Pages Affected Revision Number NA 1.0 Date 25 May, 2022 Technical support: bt.support@rodsum.com Rodsum Wireless Limited www.rodsum.com Page 2 of 22 Specification AC-BLE-T110: Mechanics Data Size Approx. 60.3 x 43.3 x 21.1 mm Weight Approx. 25 grams (without Battery) Approx. 34 grams (with Battery) Casing PC/ABS Case Electrics Data Bluetooth Chip Nordic nRF52840 Frequency 2.4GHz Memory 256kB Ram, 1MB Flash BLE Version Bluetooth 5 compatible iBeacon compatible BT4.2 Advertise Mode supported Long Range (PHY Coded) Mode supported G-force Build-in 12-bits 3-Axis Digital Accelerometer Input/ Output 1 Digital Input for Magnet Door Switch, Flood Detection 1 Digital Output reserved Interface I2C interface for external device Battery Non-rechargeable Battery CR2477 (3V 1000mAh) Life Time Base on different interval and power setting Transmission Range Up to 200m (with Long Range PHY Coded Mode) Environmental Conditions Operating Temperature -25°C to +75°C Waterproof Rating IP68 Material Resistance UV resistance Temperature Probe: Size Casing Usable temperature range Accuracy 6mm diameter by 50mm long Stainless steel tube -55 to 125°C ±0.5°C Accuracy from -10°C to +85°C Rodsum Wireless Limited www.rodsum.com Page 3 of 22 Function Description Change Mode Button Indicator LED LED Indicator Status LED Status Description Stay Off Beacon Power Off Stay On Beacon in Configuration Mode, connected with mobile Flash 1600ms Off Beacon Under Configuring Mode, not connected with any mobile 400ms On Flash 4990ms Off Beacon Under normal Advertising Mode 10ms On LED Indicator description Table Rodsum Wireless Limited www.rodsum.com Page 4 of 22 Battery Level Reporting User can enable/ disable the Battery Level Reporting by Aroco Beacon Config APP. If the function is enabled, the upper 4 bits of Major will be covered by Battery Level in advertising data. It will increase Beacon power consumption. The Battery Level bits table is shown as below: Battery Level ~10% ~20% ~30% ~40% ~50% ~60% ~70% ~80% ~90% ~100% Battery Level bits value Table Upper Bits value 4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 Double Advertise Mode User can enable/ disable the Double Advertise Mode by Aroco Beacon Config APP. If the function is enabled, beacon will advertise same data packet twice to increase the data receiving stability. It will increase Beacon power consumption. Rodsum Wireless Limited www.rodsum.com Page 5 of 22 BT4.2 Advertise Mode Normal Advertise Mode with Bluetooth 4.2 for around 50 meters transmission range. User can choose to advertise data by Normal BT4.2 Advertise Mode, Long Range (PHY Coded) Mode, or both Normal and Long Range Mode by Aroco Beacon Config APP. Long Range (PHY Coded) Mode Advertise Mode with Bluetooth 5 for long range (around 200 meters) transmission range. It request more transmission time per data and increase Beacon power consumption. Advertising Time line in different mode Rodsum Wireless Limited www.rodsum.com Page 6 of 22 Software Configuration Android App Start up Instruction 1. Download and install the AROCO BEACON CONFIG Android App (version 1.5.05) from following QR Code url: Android version: 7.0 or upper *Since the app is installed be APK, notice windows might appear while installation. Press "INSTALL ANYWAY" and "DON'T SEND" to finish the installation process. 2. Unscrew the screw and open the cover. Fill in battery CR2477 to Turn On the Beacon. Rodsum Wireless Limited www.rodsum.com Page 7 of 22 -> 3. Start the App. Allow Device's Location permission, Enable Bluetooth and Location. Rodsum Wireless Limited www.rodsum.com Page 8 of 22 4. Press the Change Mode Button on the Beacon board. Beacon will enter configuring mode · Beacon will back to Normal Mode for save energy while no any connection over 60 seconds; or press "Disconnect" Button in Mobile APP, press change mode button after Indicator LED flash. · Press and Hold the Change Mode Button 5 seconds under Normal Mode to restore all above config to default. Rodsum Wireless Limited www.rodsum.com Page 9 of 22 5. Press Magnifier Icon button on the App to scan and connect the Beacon. 6. Select the Beacon and Tap to connect. All current parameter will be read. Rodsum Wireless Limited www.rodsum.com Page 10 of 22 Common Setting Configuration UUID, Manufacturing Code, Major, Minor, Battery Level reporting, TX Power, Advertising Interval, Advertising type and PIN setting can be checked and updated in this Tab page. All current setting will be shown on the app once the beacon connection is made. Beacon will advertising with those setting in normal status. UUID: Simple 16 characters in simple (simple check box ticked) or 16 Bytes hexadecimal UUID data can be changed. (Default UUID: aa55bb44cc33dd22ee11+6 bytes Beacon MAC address) · Non-hexadecimal content will be blocked when Simple check box is un-ticked Rodsum Wireless Limited www.rodsum.com Page 11 of 22 · Simple allowed following characters 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ-_/,.* · If new simple UUID length less than 16 characters, app will fill full stop at the end of new UUID to 16 characters length and updated the parameter when "SET" button pressed. · If new UUID length not 32 in non-simple status, the notice will be shown as below when "SET" button pressed. All parameter cannot be updated. Manufacturing Code: 2 Bytes Code data can be changed. Non-hexadecimal content will be blocked. (Default: 0x004C) · If new Mfg. Code is empty, the notice will be shown as below when "SET" button pressed. All parameter cannot be updated. Major: Range 0 to 65535 (Default: 0) Minor: Range 0 to 65535 (Default: 0) · Major and Minor fixed to 0 if UUID is in simple Battery Level (Batt lvl): Tick box for choose the data advertising of Beacon Battery Level; Click Button to show the current Battery Level in mV · Battery Level reporting will cover the upper 4 bits of Major Rodsum Wireless Limited www.rodsum.com Page 12 of 22 TX Power (dBm): Combo Box choice include -20, -16, -12, -8, -4, 0, 2, 3, 4, 5, 6, 7, 8 (Default: -12) 2 x Adv: Tick box for data advertising by Double Advertisement Advertising Interval (ms): Range 50-3600000. (Default: 650) · If new Adv. Interval is empty or less than 50, the notice will be shown as below when "SET" button pressed. All parameter cannot be updated. Advertising Type: Tick Box to choice Normal Type (BT4.2) or/ and Long Range Type (BT5) (Default: Normal (BT4.2) Type only) · Tick both box for choose the both type · Power consumption will increase if BT5 Type or both type is chosen PIN: 4 digits PIN (Alphabet or number) for Login when every connection create (Default: 1234) · If new PIN length not 4, the notice will be shown as below when "SET PIN" button pressed. PIN cannot be updated. Rodsum Wireless Limited www.rodsum.com Page 13 of 22 · If PIN value incorrect, the notice will be shown at the bottom as below when connecting the beacon. Those notice message will also be shown in the "LOG" Tab page. Text notice box will be shown at the bottom if any CFG updated. Those notice message will also be shown in the "LOG" Tab page. * CONFIG APP will updated all the above parameter to Beacon by press "SET" Button. No any parameter will be updated individually if any input error notice appear. GET: All current setting value will be shown on this page when press the "GET" button REBOOT: Request beacon reboot when press the "REBOOT" button. Connection between beacon and mobile will be lost. Beacon will start will Normal mode after reboot. Rodsum Wireless Limited www.rodsum.com Page 14 of 22 Trigger Setting Configuration For Input/ Temperature Trigger Source Type, ON/OFF, Input Debounce Time, Repeat Count, Alternative UUID, Alternative Major, Alternative Minor and Alternative Advertising Interval setting will be shown, can be checked and updated. All current setting value will be shown on the app once the beacon connection is made. Beacon will trigger the Alarm by advertising with Alternative UUID, Major, Minor and Advertising Interval according those trigger setting. Rodsum Wireless Limited www.rodsum.com Page 15 of 22 Source: Combo Box for Input, Sensor (Temperature Sensor), Off and alarm type selection. Additional setting such as Digital Input Debounce time, repeat count and Action setting will be shown when any sensor type selected. · Input Alarm is reserved for other Rodsum Wireless Beacon Product. DIN Deb.(ms): (For Reserved Input Alarm Only) Repeat Count: Beacon advertise Alternative information times when alarm triggered Range: 0-5000, or 9999 0: Report Alternative information until source Trigger status changed to Off Action: Tick Box for User choose Action type for Trigger (1 or both action) Alt. Uuid: Advertising alternative information instead of normal information when alarm triggered Dout: Reserved for other Rodsum Wireless Beacon Product If one of parameter out of range, the notice will be shown in RED in that row when "SET TRIG" button pressed. All TRIG parameter cannot be updated. All current TRIG setting value will be shown when press the "GET TRIG" button Text notice box will be shown at the bottom if any TRIG CFG updated. Those notice message will also be shown in the "LOG" Tab page. Rodsum Wireless Limited www.rodsum.com Page 16 of 22 Alternative Information: Include UUID, Major, Minor and Advertising Interval. Beacon will advertise those alternative information instead of normal information when alarm triggered. Alt. UUID: Simple 16 characters in simple (simple check box ticked) or 16 Bytes hexadecimal UUID data can be changed. (Default alt. UUID: aa55bb44cc33dd22ee11+6 bytes Beacon MAC address) Alt. Major: Range 0 to 65535 (Default: 0) Alt. Minor: Range 0 to 65535 (Default: 0) · Non-hexadecimal content will be blocked when Simple check box is un-ticked · Simple allowed following characters 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ-_/,.* · If new simple UUID length less than 16 characters, app will fill full stop at the end of new UUID to 16 characters length and updated the parameter when "SET" button pressed. · If new UUID length not 32 in non-simple status, the notice will be shown as below when "SET" button pressed. All parameter cannot be updated. · Major and Minor parameter fixed to 0 if UUID is in simple Alt. Adv. Int(ms): Range 0 or 50 to 3600000 (Default: 0) · Alternative Advertising Interval = 0, Beacon will use normal advertising interval setting on Alternative advertising All current Alternative information setting value will be shown when press the "GET ALT. UUID" button Text notice box will be shown at the bottom if any Alt UUID CFG updated. Those notice message will also be shown in the "LOG" Tab page. Rodsum Wireless Limited www.rodsum.com Page 17 of 22 Rodsum Wireless Limited www.rodsum.com Page 18 of 22 Temperature Sensor Configuration Sensor Read Interval and Operation setting will be shown, can be checked and updated. All current setting value will be shown on the app once the beacon connection is made. Beacon will follow the reading interval and operation setting to run Temperature Sensor related function Interval(s): Sensor Reading Interval Range 0,5 to 86400 (Default: 0 - Disable) * Power consumption will increase if Reading Interval is shorter Operation: Beacon will operate following function when the Interval not equal to 0 · Report: Temperature (Celsius) will be reported with data advertising in Minor For example: current temperature 23.9°C, Data minor is 239 Rodsum Wireless Limited www.rodsum.com Page 19 of 22 current temperature -4.5°C, Data Minor is 65489 (Bitwise NOT when temperature lower than 0°C) · Trigger(Over): Trigger will turn On when current temperature over than the preset limit · Trigger(Under): Trigger will turn On when current temperature lower than the preset limit · Trigger(In range): Trigger will turn On when current temperature between the preset upper and lower temperature · Trigger(Out range): Trigger will turn On when current temperature NOT between the preset upper and lower temperature * Different Trigger Limit will be shown below the operation row after different Operation is chosen ** All Temperature Trigger Limit Range is -80 to +150°C *** Current temperature will advertising in Minor in all trigger operation too **** Preset Normal Minor/ Alt. Minor will be replaced by the temperature when sensor is enabled ***** If temperature sensor interval larger than advertising interval, beacon will keep reporting the last temperature value in Minor until the new temperature reading received Rodsum Wireless Limited www.rodsum.com Page 20 of 22 If one of updated parameter out of range, the notice in RED will be shown in that ROW when "SET SENSOR" button pressed. No any parameter will be updated individually if any input error notice appear. Text notice box will be shown at the bottom if any SENSOR config updated. All current setting value will be shown when press the "GET SENSOR" button Those notice message will also be shown in the "LOG" Tab page. Rodsum Wireless Limited www.rodsum.com Page 21 of 22 Finish Configuration Please go to "COMMON" tab page and press "REBOOT" button when every setting is updated. Beacon will reboot immediately, disconnect with mobile APP, and ready to start the beacon normal operation. Log All activity will be logged with time and shown on this log tab page. Rodsum Wireless Limited www.rodsum.com Page 22 of 22