Counterbalance Monitor Wall Mount
DELTACO ARM-0361
Introduction
This document provides installation instructions and safety information for the DELTACO ARM-0361 Counterbalance Monitor Wall Mount. This mount allows for flexible positioning of your monitor, offering ergonomic benefits and space-saving solutions.
Safety Warnings
- ⚠️Stored Energy: Hold the monitor arm firmly with one hand on each opposite side. Ask another person to cut the cable tie. Slowly release pressure until fully extended.
- ⚠️Weight Limit: Do not exceed the marked maximum weight capacity of the mount. Serious injury or property damage may occur!
- ⚠️Choking Hazard: This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- ⚠️Indoor Use Only: This product is intended for indoor use only. Outdoor use may lead to product failure and personal injury.
- ⚠️Installation: Improper installation may result in serious injury. This product should only be installed by a qualified person. Ensure the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- ⚠️General Caution: Usage with products heavier than the rated weight may result in instability and potential injury.
Specifications
Dimensions
The mount offers adjustable reach and tilt. Key dimensions include:
- Arm extension: 40 mm to 160 mm
- Minimum monitor width: 225 mm
- Maximum monitor width: 290 mm
- Base depth: 50 mm
- Maximum monitor height: 250 mm
- Pivot angles: ±45°, ±90°, ±180°
- Base plate dimensions: 83 mm
- VESA plate dimensions: 75x75 mm, 100x100 mm, 115x115 mm (approximate, based on diagrams)
Included Parts
| Part | Quantity | Description |
|---|---|---|
| A | x1 | Wall Mount Bracket |
| B | x3 | Washers (for wood stud mounting) |
| C | x1 | Allen Key |
| W-A | x3 | ST6.3x55 Screws (for wood studs) |
| W-B | x3 | Ø10x45 Screws (for concrete/brick) |
| W-C | x3 | Washers (for concrete/brick mounting) |
| M-A | x4 | M4x12 Screws (for monitor attachment) |
| M-B | x4 | M5x12 Screws (for monitor attachment) |
| M-C | x4 | D5 Washers (for monitor attachment) |
Installation Guide
Ensure you have all parts listed above before proceeding. Installation requires a qualified person and appropriate tools.
Step 1: Prepare Mounting Location
This mount is designed for installation on wooden stud walls, solid concrete walls, or brick walls.
- For Wooden Studs: Drill a hole approximately 4.5 mm (3/16") in diameter and 55 mm (2.2") deep into the stud.
- For Concrete/Brick Walls: Drill a hole approximately 10 mm (3/8") in diameter and 60 mm (2.4") deep.
? Use safety gear and proper tools.
Step 2: Mount the Bracket to the Wall
Attach the Wall Mount Bracket (A) to the prepared wall location.
- For Wooden Studs: Use screws W-A (x3) with washers B (x3).
- For Concrete/Brick Walls: Use screws W-B (x3) with washers W-C (x3).
Do not overtighten the screws. Ensure the bracket is securely fastened.
Step 3: Attach Monitor to Arm
Attach your monitor to the VESA mounting plate on the arm.
Use the provided screws (M-A or M-B) and washers (M-C) that best fit your monitor's VESA mounting holes. Ensure the screws are not too long or too short for your monitor's casing.
? Select appropriate screws (M-A or M-B) and washers (M-C).
Step 4: Adjust Tension
The arm contains stored energy. Follow the safety instructions carefully when releasing the cable tie.
To adjust the monitor arm's tension for smooth up/down movement:
- To decrease tension (allow arm to fall): Turn the adjustment screw counter-clockwise ↩️.
- To increase tension (prevent arm from falling): Turn the adjustment screw clockwise ↪️.
Adjust until the monitor stays in the desired position without drifting.
Maintenance and Checks
Regular checks are recommended (at least every three months) to ensure the wall mount is secure and safe to use.
Manufacturer Information
SweDeltaco AB, Glasfibergatan 8, 125 45 Älvsjö, Sweden.
