Soldering and Rework equipment for electronics | JBC Soldering
Instruction Manual for JBC Tools models including: DS360, DR560, DS360 Desoldering Iron Stand, DS360, Desoldering Iron Stand, Iron Stand, Stand
DDSE - 2-Tool Rework Station
File Info : application/pdf, 12 Pages, 4.56MB
DocumentDocumentINSTRUCTION MANUAL DSS / DRS Stand for Desoldering Iron This manual corresponds to the following references: DS-SF (for DS360) DR-SF (for DR560) Packing List Box includes one stand according to purchased reference. Stand for DS360 Micro Desoldering Iron ............ 1unit Stand for DR560 Desoldering Iron ..................... 1 unit The following items are included in each stand: Stand Cable 1m ............ 1 unit Ref. 0024227 Sponge for Modular Tool Stands ................... 1 unit Ref. S7034 Brass Wool .................... 1 unit Ref. CL6210 Cable Holder ................. 1 unit Connecting Clip Set .... 1 unit Ref. 0024028 (already assembled) Ref. 0011356 (includes 2 pieces) Manual ............................. 1 unit Ref. 0027183 2 Features and Connections w w w.j b c to o l s .c o m CC1001 Cable Collector Tip Holder Tip Exchanger S7034 Sponge H6272 Tool Holder CL6210 Brass Wool (inside) CL7889 Wiper To Control Unit To Tool 3 Assembly Adjustable Cable Collector (CC1001) Insert the cable into the clip and then insert into the cable collector. Do not leave the cable longer than necessary to reach the work area freely. The cable collector is flexible. It accompanies and adapts to the movements during the soldering process. Wiper (CL7889) Adjustable Tool Holder (H6272) The wiper offers different ways to clean the cartridge tips. If desired use the included sponge. 4 Adjust the tool holder angle to suit the work position. Tip Cleaner w w w.j b c to o l s .c o m Select the option to suit your needs and improve the thermal transfer of the tip. CL6210 Brass Wool Very effective cleaning method. Leaves a small layer of solder on the tip preventing oxidation between cleaning and rewetting. If the tip is very dirty, JBC recommends first the cleaning with the wiper to remove excess solder. Wiper The integrated wiper offers different ways to clean the cartridge tips. Tapping Wiping Sponge Tap gently to remove excess solder. Use the slots to remove the remaining particles. The softest cleaning method. Keep the sponge damp with distilled water when working to avoid tip wear. 5 Tip Extractor Ref. DS-SF Tip Holder Ref. DR-SF Tip Holder Place the Soldering Iron with the assembled tip in the extractor groove, pull the tool towards and DS360 remove the tip. Put on the new tip and press slightly to ensure its correct postion. Unused tips can be stored in the extractor openings. Spanner The Spanner is used to unscrew and replace the tips. When not in use it can be stored inside the extractor. Unused tips can be stored in the extractor openings. Wiper and Brass Wool Replacement The wiper and brass wool can easily be removed for cleaning or replacement when they are worn. Lift the wiper at its front edge. Remove the wiper by pulling it out. Replace the brass wool with a new one when it is worn out. Place the wiper back o replace them if desired. 6 Accessories Connection between Stand DRS, Control Unit and Module A1287 Suction Extension Tube Kit (Length: 1.5m) w w w.j b c to o l s .c o m A1286 Extension lead for stands (Length: 1.5 m) Stand cable DRS Stand for DR560 Desoldering Iron 7 Maintenance Before carrying out maintenance or storage, always unplug the stand from the station and the tool. - Use a damp cloth to clean the stand. Alcohol can be used only when cleaning the metal parts. - Check periodically that the metal parts of the tool/stand are clean so that the station can check the tool's status. - Periodically check all cables and tube connections. - Replace any defective or damaged parts. Use original JBC spare parts only. - Repairs should only be performed by a JBC authorized technical service. Clean periodically 8 Safety w w w.j b c to o l s .c o m It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the stand for any other purpose than soldering or rework. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire. - The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position. - Avoid the contact of flux with skin or eyes to prevent irritation. - Be careful with the fumes produced when soldering. - Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm. - Utmost care must be taken with liquid tin waste which can cause burns. - This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance. - Maintenance must not be carried out by children unless supervised. 9 Notes 10 Notes w w w.j b c to o l s .c o m 11 Specifications DSS Stand for DS360 Micro Desoldering Iron Ref.: DS-SF - Includes Sleep Mode - Total Net Weight 1500 g / 3.31 lb - Package Dimensions/Weight 1062 g / 2.34 lb (L x W x H) 342 x 155 x 120 mm / 13.46 x 6.10 x 4.72 in DRS Stand for DR560 Desoldering Iron Ref.: DR-SF - Includes - Net Weight - Package Dimensions/Weight (L x W x H) Sleep Mode 2172 g / 4.79 lb 1608 g / 3.55 lb 342 x 155 x 120 mm / 13.46 x 6.10 x 4.72 in Complies with CE standards ESD safe Warranty JBC's 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility. 0027183-030624