accommodated.It
frigeration.com
Premium Undercounter Products for Home & Outdoor | Marvel Refrigeration
Owner's Manual for MARVEL models including: MPBD424-IG31A Undercounter Refrigeration, MPBD424-IG31A, Undercounter Refrigeration, Refrigeration
Marvel MPBD424IG31A MPBD424IG31A 768388081461
File Info : application/pdf, 8 Pages, 2.68MB
DocumentDocumentOWNER'S GUIDE & SERVICE MANUAL MARVEL UNDERCOUNTER REFRIGERATION Model: MPBD424-IG31A WELCOME Welcome to the Marvel Experience! Thank you for choosing our quality American-built product to add to your home. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support. The information in this guide is intended to help you install and maintain your new Marvel undercounter model to protect and prolong its lifetime. We encourage you to contact our Technical Support team at (616) 754-5601 with any questions. Warranty Registration It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.marvelrefrigeration.com. The following information will be required when registering your appliance: Service Number Serial Number Date of Purchase Dealer's name and address Online registration available at www.marvelrefriger- ation.com Got a Marvelous Design? We would love to see how your Marvel product looks in its new home. Send us photos at marketing@marvelrefrigeration.com, and we might feature your Marvel home design on our website and social media! The service number and serial number can be found on the serial plate which is located inside the cabinet on the left side near the top. MARVEL Bonus Third-Year Warranty Free with Product Registration Your Marvel Professional product qualifies for a one-year extension of the two-year warranty coverage from your date of purchase, free of charge. To take advantage of this third-year warranty, be sure to reg-ister your product with Marvel within 60 days from the date of purchase at marvelrefrigeration.com and provide proof of purchase. XXXXXXXXXXXX XXXXXXXXXXXX R600A g Thank you again for investing in Marvel for your home! TABLE OF CONTENTS Tip: Click on any section below to jump directly there Installation Integrated Panel Dimensions Integrated Panel Installation 3 INTEGRATED PANEL DIMENSIONS Top of door Clearance for hinge at top and bottom Clearance for hinge at top and bottom Top of door Hinge side of door Hinge side of door Left Hand Hinged Door 24" (61 cm) wide appliance Right Hand Hinged Door 24" (61 cm) wide appliance 1/4" [0.6cm] 3-3/4" 3-3/4" 4" 4" [9.5cm] [10.1cm] 2" 2" [5.1cm] 3" [7.6cm] 3" 3" [7.6cm] 30-7/16" 15/32" (2.9 c1m5)-1/4" [38.7cm] 30-7/16" [77.3cm] 2" 2" [5.1cm] 4" [10.1cm] 3-3/4" 4" Left Hand Hinged Door 24" (61 cm) wide appliance Right Hand Hinged Door 24" (61 cm) wide appliance 4 3" 15-1/4" INTEGRATED PANEL INSTALLATION Integrated door panel installation: If you purchased an integrated panel model, your unit is equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of 5/8" (15 mm) and 3/4" (18 mm) are accommodated. ! CAUTION It is important to use the factory provided grille that came with the product to assure proper air flow is maintained through the condenser. The use of a custom grille is not recommended and will void the warranty. ! WARNING Integrated panel models are designed for use with built-in installations only. Use in freestanding installations could result in personal injury. Step 1: Removing the Door Open the door and loosen the screws holding the hinges to the cabinet (2 at the top and 2 at the bottom hinge). Do not remove the screws but loosen them enough so the hinges can be slipped off of the screws when sliding the door to the side. ! WARNING The articulated hinges have many pinch points. Carefully close / collapse the hinges as soon as the door is removed from the cabinet. With a helper, and being careful not to scratch the cabinet or the door, slide the door to the side about 1/2 inch and remove the hinges and door from the unit. 5 INTEGRATED PANEL INSTALLATION ! WARNING Use extreme caution with the articulated hinges. The hinge is self closing and many pinch points exist prior to built-in installation. Do not remove the cabinet "Z" bracket from the top of the cabinet. Step 2: Remove the door gasket With the door laying on a flat surface and starting at a corner of the door remove the magnetic door gasket from the interior side of the door, see Figure 17. Set the gasket aside on a flat surface. There are 10 holes in the gasket retainer extrusions, (3 on each side and 2 at the top and bottom which are used to fasten the panel to the front of the door. The screws are provided in the literature pack along with the door lock, which is provided on certain models. Loosen (do not remove ) these 2 phillips head screws on the top and bottom hinges Holes in gasket retainer. Figure 24a Integrated panel flush with top and side of door. Integrated panel to be centered on width of door. Cabinet "Z" Bracket Figure 23a Figure 23 "P" clamp and screw Figure 23b Bottom of door Wire connector see Figure 6 Figure 24 Magnetic Gasket remove starting at a corner, grasp and pull away from the door. Step 3: Cut and drill the integrated panel Depending on your model cut the integrated door panel to the dimensions shown in Figures 19 to 22. The window cut out is for glass door models only. If your appliance has a lock also drill the lock hole in the panel, see Figure 25. 6 INTEGRATED PANEL INSTALLATION ! CAUTION Weight of integrated door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Material Type Hardwood Softwood #10 Wood Screw 1/8" (3.2 mm) 8 Diameter. Pilot Ho7le /7 64 (2.8 mm) Diameter. Pilot Hole Table A D #10 x 1/2" screw 6 Hinge side of door Step 4: Assemble the panel to the door The preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom integrated panel should be flush with the top of the dooCr and centered along the width of the door. See Figure 16a. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in Table "A", being careful not to drill through the front surface of the panel. If the integrated panel is thinner than 5/8" (16 mm) thick shorter screws will have to be obtained. Fasten the panel to the door with the 10 screws provided in the literature pack. (See Figure 25a). Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket iBnto the channels. Be sure the gasket corners are seated properly. Figure 25a 5 4 1/2" (13 mm) diameter drill through door panel, from other side 13/16" (20.5 mm) counter bore, 7/16" (11 mm) deep. Counter bore lock hole on back side. A 8 7 6 7 Figure 25 - Back of Panel 5 4 INTEGRATED PANEL INSTALLATION Step 5: Assemble lock parts Two (2) lock extensions are provided with the lock. Use the longer extension for 3/4" thick integrated panels and the shorter one for 5/8" thick integrated panels. Assemble the lock extension, cam stop washer, spring washer, and set screw to the lock as shown in Figure 26 and 27. Install this lock assembly into the lock hole in the integrated panel and secure with the retaining nut on the back side with a 15 mm socket and ratchet. Make sure the key slot in the front of the lock is vertical. Step 7: Install the door Carefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 25 and 25a). BRASS EXTENSION SPRING WASHER NUT LOCK 1/2 HOLE 13/16 COUNTER BORE 7/16 DEEP CAM PHILLIPS SCREW Step 8: Secure the cabinet Use the #8 x 3/4" black screws from the literature pack to secure the counter top to the cabinet top through the holes in the cabinet "Z" bracket. 3/4 INCH WOOD PANEL SECTION A-A SCALE 1 : 1 Figure 26 INNER DOOR Cabinet "Z" bracket Step 6: Install lock cam Attach the lock cam to the back of the lock assembly with the phillips head screw provided. Orient the lock cam vertically when installing on the lock. #8 x 3/4" black screws (3 places) Cam Screw Spring washer Brass Retainer nut extension (2 lengths provided) Cam stop Key washer Set screw Lock Figure 27 8 Figure 28