User Manual for SEEKCY models including: 2A9XB-AG2, 2A9XBAG2, ag2, AG2 AOA Positioning Base Station, AOA Positioning Base Station, Positioning Base Station, Base Station
Locsmart IoT Technology (Suzhou) Co., Ltd AG2 AOA Positioning Base Station 2A9XB-AG2 2A9XBAG2 ag2
AOA Positioning Base Station AG2 product manual V1.1 Table of Contents 1. Product Description ................................................................................................................................. 2 2. Product features ........................................................................................................................................ 3 3. Product parameters ................................................................................................................................. 3 4. Installation instructions ......................................................................................................................... 4 4.1 Interface description.................................................................................................................... 4 4.2 Installation instructions ............................................................................................................. 5 4.3 Instructions for use ...................................................................................................................... 6 4.4 Precautions....................................................................................................................................... 6 1. Product Description The AG2 AOA Positioning Base Station by Suzhou Xunxi Electronic Technology Co., Ltd. adopts 2.4GHz Bluetooth AoA arrival angle precise positioning technology, combined with high-precision positioning antenna array, and self-developed highprecision Self-Adaptation algorithm, with real-time positioning accuracy up to submeter level. This product uses standard Ethernet data communication and 802.3af/at standard POE power supply. Note: The AG2 AOA Positioning Base Station is only a part of the information seeking electronic Bluetooth AoA positioning system. For the overall installation, deployment, and debugging guidelines of the Open Platform, positioning engine, and other components involved in the Bluetooth AoA positioning system, please refer to other documents. This article will not elaborate. Figure 1 AG2 AOA Positioning Base Station 2. Product features Rounded square ceiling design, beautiful and technologically advanced, easy to install. A single locator can achieve high-precision two-dimensional positioning. Standard POE power supply, no need for additional wiring power supply. 3. Product parameters Table 1 AG2 AOA Positioning Base Station parameters Positioning locator Model Shell material Shell color External dimensions Product weight Use power Supply voltage Antenna category Power consumption of the whole machine Working temperature Storage temperature Operating humidity Communication protocol Operating frequency band AG2 ABS+PC White 230*230*50mm About 650g POE power supply POE 48V PCB Antenna 2W -20~+60 -40~80 0%~90% 2.4GHz and above BLE4.2 2.401~2.481GHz Location coverage Installation height range 2H (open environment) H1m~10m Positioning accuracy Data postback Network interface Network indicator light * Indicator at 25 0.1m~1m IEEE802.3 af/at 10/100Mbps RJ45 Support 4. Installation instructions 4.1 Interface description RJ45 interface: POE power supply and data postback interface, which can be connected to standard POE switch through network cable to realize power supply network. Reset button: Restore factory settings button, press and hold for 3 seconds, the green light of the locator will flash 5 times, indicating that the factory settings have been successfully restored. The specific interface is shown in the following figure: Reset button RJ45 interface Figure 2 Schematic diagram of AG2 positioning locator interface 4.2 Installation instructions * Before installation, please confirm that the fixed position can withstand a weight of 2KG or more. Install the mounting bracket firmly on the ceiling using M4 bolts as shown in the figure below. Connect the network cable to the RJ45 interface of the locator. Align the mounting bracket buckle position and push the locator into the mounting bracket buckle. The installation bracket is shown in the figure below. Figure 3 Schematic diagram of AG2 positioning locator installation bracket 4.3 Instructions for use After the locator is properly installed and connected to the POE switch, the locator will start automatically. After starting, the operating status of the locator can be judged by the indicator light. The indicator light rules are shown in the following table: Table 2 AG2 positioning locator indicator light description Serial number Status Description 1 Green light flashing Locator start 2 Red light flashing slowly Getting IP Address 3 Green light flashing Get IP Address slowly Successfully 4 The green light is always Connected positioning on engine successfully 5 The traffic lights are not Locator failure on 4.4 Precautions 1. AG2 positioning locators must use the specified standard POE power supply equipment for power supply (PSE equipment that complies with IEEE 802.3af/at protocol). 2. The locator is a wireless communication device that operates at -20 ° C to + 60 ° C, with a humidity of 0 to 90% in a non-condensing indoor environment. It should avoid rain or prolonged outdoor exposure, stay away from fire sources and strong electromagnetic interference sources, and try to avoid contact with high-voltage environments to avoid affecting normal function and damaging equipment. 3. Do not subject this product and its accessories to strong shocks or vibrations to avoid damaging this product and its accessories and causing malfunctions. 4. Please use original accessories (antenna, power supply, etc.). The use of nonoriginal accessories may damage the equipment or affect performance. If there are changes to product specifications and accessories, the actual product shall prevail without further notice. Statement: The content of this manual is for reference only. If there are any changes, no further notice will be given. Suzhou Xunxi Electronic Technology Co., Ltd. has the final interpretation right of the content of this manual. Revision record Revision date Revised version Reviewers Modify the content 2021/7/31 V1.0 Lina Xu New regulations made 2022/5/16 V1.1 Lina Xu Modify shell details, parameter confirmation FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimumdistance 20cm between the radiator &your body.Microsoft Word 2013 Microsoft Word 2013