OUTPUT.IT
User Guide for ZFX models including: Alpha1PB Wireless TV Headphone, Alpha1PB, Wireless TV Headphone, Headphone
Shenzhen ZFX Technology CO.,Ltd ALPHA Wireless TV Headphone 2AMLDALPHA 2AMLDALPHA alpha
File Info : application/pdf, 11 Pages, 1.02MB
DocumentDocumentWireless TV Headphone Alpha1PB Alpha, Alpha1PG USER GUIDE ZFX PACKAGE INCLUDE 1. 1. Headphone 2. Transmitter&charging base station 3. USB-C adapter 4. 3.5mm audio cable 01 02 03 04 PRODUCT OVERVIEW 1. Charging pogo pin 2. Led indicator 3. Volume 4. Mute button&Eq button 5. Power on/off button 6. Volume + 01 02 03 04 05 06 PRODUCT OVERVIEW 07. Charging/boardcast LED indicator 08. Aux input 09. RAC(L) 10. RAC(R) 11. Optical in 12. Optical out 13. USB-C for power 07 08 09 10 11 12 13 CONNECT TO TV CONNECT TO TV Use the Type-C adapter to connect the base station for power supply. Power on the headphone,the LED indicator on headphone and base station will turn to soild blue. 1.3.5mm Audio source Use 3.5mm to 3.5mm cable connect TV to base station(AUX input jack) You can also use the RCA to 3.5mm cable connect your TV(RCA output jack) to base station(AUX input jack) 2.Optical audio source Use the Optical cable connect your TV(optical output) to base station(optical input) Select the audio output to optical in your TV setup menu. · OPTICAL AUDIO OUT AUDIO OUT AUDIO IN PHONE COAXIAL SETUP TV MENU TV AUDIO Out Checking and TV Speaker Setting(Use TV remote control) if you can not hear sound from your headphones after connecting: 1.Ensure use TV Red/White RCA ports labeled"AUDIO OUT"or "OUTPUT"other Red/White ports are incorrect. 2. Ensure your TV speaker is set to External Spearker 3.Use the RCA cable(OPTICAL cable) to plug the headphone into the RCA(OPTICAL) output of the TV to test if you can hear the TV sound. Notes: *If your TV only support single sound out,the TV's speaker will be either automatically muted when you plug something into an audio out port(OPTICAL/PCA/AUX,etc.)or they become disableed once you choose External Speaker as your TV's audio output.It's depends on TV circuit design. Audio Forma: PCM Dolby Digital DTS DTS Neo2.5 Speakers Internal speakers External speakers Headset CHARGING You can hang the headphone to the base station for charging, make sure that the headphone and the base are in correct contact, and the charging indicator light is on. *The headset will turn off automatically when the power exhauste.d PAIRING Connect to base station 1.Power on the headphone. 2. Use the type-C adapter to connect base station for power supply, audio input to keep the base station working. 3.The headphone will connect to base station automatically. Headphone status Buzzer status Led status Transmitter status Led statu s Power on Power on blue led flash headset put on for charge red led on base station connect / base station disconnect / Headphone charge / headphone charge full or / no charge blue led solid blue led flash headset not put and detect music input blue led on headset put on fully charge or not put on and no music input led off red led on led off FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction