download.schneider-electric.com/files?p_Doc_Ref=CCT593012_HW
User Guide for CLIPSAL models including: PDL593011 Temperature Humidity Sensor, PDL593011, Temperature Humidity Sensor, Humidity Sensor, Sensor
File Info : application/pdf, 28 Pages, 4.47MB
DocumentDocumentWiser Temperature/Humidity Sensor Device user guide Information about features and functionality of the device. 09/2024 www.clipsal.com Legal Information The information provided in this document contains general descriptions, technical characteristics and/or recommendations related to products/solutions. This document is not intended as a substitute for a detailed study or operational and site-specific development or schematic plan. It is not to be used for determining suitability or reliability of the products/solutions for specific user applications. It is the duty of any such user to perform or have any professional expert of its choice (integrator, specifier or the like) perform the appropriate and comprehensive risk analysis, evaluation and testing of the products/solutions with respect to the relevant specific application or use thereof. The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this document are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owner. This document and its content are protected under applicable copyright laws and provided for informative use only. No part of this document may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric. Schneider Electric does not grant any right or license for commercial use of the document or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric reserves the right to make changes or updates with respect to or in the content of this document or the format thereof, at any time without notice. To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this document, as well as any non-intended use or misuse of the content thereof. Table of Contents Safety Information.......................................................................................4 Wiser Temperature/Humidity Sensor .......................................................5 About the device.........................................................................................5 Installing the device ....................................................................................6 Pairing the device .......................................................................................6 Configuring the device ................................................................................8 Renaming the device ............................................................................8 Setting the device location .....................................................................9 Using the device.......................................................................................10 Checking the device history ................................................................. 11 Identifying the device ..........................................................................12 Automation ......................................................................................... 13 Removing the device ................................................................................21 Resetting the device .................................................................................23 Replacing the battery ................................................................................24 LED indications ........................................................................................24 Troubleshooting .......................................................................................25 Technical Data .........................................................................................25 Compliance ................................................................................................26 Compliance information for Green Premium products..................................26 Trademarks.............................................................................................. 26 DUG_Temperature and Humidity Sensor_WHP-01 3 Safety Information Safety Information Important Information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a "Danger" or "Warning" safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury. 4 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Wiser Temperature/Humidity Sensor CLP593011 PDL593011 About the device The Wiser Temperature/Humidity sensor (hereinafter referred to as sensor) combines two sensors in one unit. The sensor measures temperature and humidity in the environment where the sensor is installed. When the sensor is connected to the Wiser Hub, it reports the temperature and humidity data to the Wiser Hub. The sensor triggers other Wiser devices (such as turning on an air conditioner if the temperature is high or turning on an exhaust fan if the humidity is high) through automation. Features of the sensor: · Detect temperature and humidity in the environment and passes the information to the Wiser Hub. · Sends the battery level and offline device status information to the Wiser Hub. Operating elements A. Status LED B. Function key A B DUG_Temperature and Humidity Sensor_WHP-01 5 Installing the device Wiser Temperature/Humidity Sensor Refer to the installation instruction supplied with this product. See Wiser Temperature Humidity Sensor. NOTICE EQUIPMENT DAMAGE Do not install the sensor in a place where there is strong sunlight or wind (for example, close to the ventilation). Failure to follow these instructions can result in equipment damage. Pairing the device Using the Wiser Home app, you can pair your sensor with the Wiser Hub to access and control the sensor. 1. On the Home page, tap . 2. Tap Devices > >Climate. 3. Tap Temperature/Humidity Sensor > Next. The next screen shows the sensor joining process. Temp/Humidity Sensor Setup Remove the mounting plate and remove the battery isolating tape before proceeding. Next 6 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor 4. Short press the function key 3 times (< 0,5 s). The LED blinks amber. 3× < 0,5 s 5. Wait for a few seconds until the sensor LED turns green. TIP: The stable green LED on the sensor shows that it is successfully connected to the Wiser Hub. ... You will see Device joined at the bottom of the screen once the sensor has been successfully connected to the Wiser Hub. Temp/Humidity Sensor Setup Press the function key on the device three times rapidly until the LED blinks amber. Device Joined 6. Ensure that the first battery cover is securely fastened, then install the sensor on the baseplate. For more information, refer to the installation instruction. 7. Tap Next to enter the sensor name. 8. Tap Next to assign room location and then tap Submit. TIP: You can find the paired sensor name and its location on the All or Room tab on the Home page. DUG_Temperature and Humidity Sensor_WHP-01 7 Configuring the device Wiser Temperature/Humidity Sensor Renaming the device Using the Wiser Home app, you can rename the sensor. To rename the sensor: 1. On the Home page, tap . 2. Tap Devices > Temperature/Humidity Sensor > Device Name (A). TIP: Additionally, you can rename the sensor by tapping on the Home page Temperature/Humidity Sensor > Device settings > Device Name (A). Device Details Temp/Humidity Sensor Battery OPTIONS Device Name Temperature/Humidity Sensory A Location Living Room ABOUT Firmware Version 00.00.000y Identify Delete 8 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Setting the device location You can change the device location using Wiser Home app (such as bedroom, living room, dining room etc.). 1. On the Home page, tap . 2. Tap Devices, select the device from the list for which you wish to change the location. 3. Tap Location to open setup page. 4. On setup page, you can enter New room name (A) or select an existing room from the list (B). Device Setup Where does this device control? New room name A Living Room 3 Devices Kitchen 2 Devices B Bathroom 3 Devices Bedroom 2 Devices Remove from Room C Submit D TIP: If the device is already assigned, you can remove it from the existing room. Tap Remove from Room (C). 5. Once changes are done, tap Submit (D). DUG_Temperature and Humidity Sensor_WHP-01 9 Using the device Wiser Temperature/Humidity Sensor The Control Panel of the sensor allows you to view the real-time temperature and humidity values. On the Home page, tap All > Temperature/Humidity Sensor to access the control panel. On the sensor control panel page, you can see the following: · The current temperature value (A) · The current humidity value (B) · History (C) · Device settings (D) Back Temp/Humidity A Temperature 19.5 B Humidity 47% History C Device settings D 10 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Checking the device history Using the Wiser Home app, you can view the sensor's history which displays room temperature and humidity values recorded as an event. The sensor records each event and stores it in the cloud. NOTE: If the cloud connection is lost, the sensor's history page will not display the temperature and humidity values. To view the sensor history: 1. On the Home page, tap All > Temperature/Humidity Sensor. 2. On the device control panel page, tap History. History TODAY 09:42:42 17:21:35 53% Humidity 62% Humidity YESTERDAY 11:42:42 53% Humidity 20TH DECEMBER 2021 06:42:42 66% Humidity 19TH DECEMBER 2021 23:42:42 44% Humidity DUG_Temperature and Humidity Sensor_WHP-01 11 Wiser Temperature/Humidity Sensor Identifying the device Using the Wiser Home app, you can identify the sensor from the other available devices in the room. To identify the sensor: 1. On the Home page, tap . NOTE: Please wake up the sensor (press the function key). 2. Tap Devices > Temperature/Humidity Sensor > Identify (A). TIP: Additionally, you can identify the sensor by tapping on the Home page Temperature/Humidity Sensor > Device settings > Identify (A). NOTE: The sensor LED blinks to identify the sensor and it continues blinking green until you tap OK. Device Details Temp/Humidity Sensor Battery Good Signal (-30dBm) ? OPTIONS Device Name Temperature/Humidity Sensory Location Living Room ABOUT Firmware Version 00.00.000y Identify A Delete 12 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Automation An automation allows you to trigger an action automatically or at scheduled times. By using the Wiser Home app, you can create automations based on your needs. This example demonstrates how a device works when the condition is met. Creating an automation 1. On the Home page, tap . 2. Go to Automation > to create an automation. NOTE: Maximum 10 automations can be added. 3. Tap If (A) and select any of the following conditions (B): All conditions: This triggers an action only when all conditions are met. Any condition: This triggers an action when at least one condition is met. Close New automation Save e.g. Good Morning A If When Then Conditions are met All conditions 0 of 10 Any condition B Start by adding a condition that will trigger your automation. Add conditions DUG_Temperature and Humidity Sensor_WHP-01 13 Wiser Temperature/Humidity Sensor 4. Tap Add conditions and select any of the following (C): Device status change: Select a device to enable automation. Away Mode: Enable/Disable away mode to trigger an action. TIP: Away mode can also be used as a trigger to turn off the lights, dimmer or closing the shutter etc. For more information refer to Away mode. Add conditions Please choose the triggers to activate your automation. Device status change E.g. if motion is detected C Away Mode E.g. if away mode is on 5. Tap Device status change > Temperature/Humidity Sensor > Temperature, Set the temperature using sliding bar (D) and select the condition (E) (less than / more than), then tap Set. Back Temp bedroom Set D ° less than E NOTE: · Maximum 10 conditions can be added. · To remove an added condition, swipe left and tap . 14 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor 6. To set a specific time for your automation, tap When > Add time and select any of the following (F): Specific time of the day: Sunrise, Sunset, Custom. Period of time: Daytime, Night time, Custom. Add time F NOTE: · Maximum 10 entries can be added · To remove a specific time, swipe left and tap . 7. To add an action, tap Then > Add an action and select any of the following (G): Control a device: Select a devices that you want to trigger. Send notification: Turn on the notification for the automation. Activate a moment: Select the moment that you want to trigger. Wait: This option allows you to add a delay in an automation sequence. You can set the wait time in increments of 1 hour and 1 minute, up to a maximum of 24 hours. This feature is useful for delaying actions within an automation. Add an action Please choose an action for your automation. Control a device E.g. turn the light on E.g. if the motion is detected G Activate a moment E.g. enable Away mode Wait E.g. wait 10 mins until next action DUG_Temperature and Humidity Sensor_WHP-01 15 Wiser Temperature/Humidity Sensor 8. Tap Control a device > Heating and select any of the following (H): Boost: Set the duration to increase the temperature by 2° C. Setpoint: Set the desired temperature. Select device Please select a device that will activate All PleRasaedicahtoorose what you would like BooBsltind control switch H Setpoint Cancel 9. Tap Setpoint, set the required temperature using vertical sliding bar (I), then tap Set. Back Heating Set I NOTE: · Maximum 10 actions can be added. · To remove an action, swipe it left on the action and then tap . 16 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor 10. Enter the automation name (J). You can choose the cover image that represents your automation by tapping . Close New automation Save J If Run this action When Then 0 of 10 Add an action 11. Tap Save. Once the automation is saved, it is visible on the Automation tab. Using the (K) you can enable and disable the automation. Automations Schedules Device K DUG_Temperature and Humidity Sensor_WHP-01 17 Wiser Temperature/Humidity Sensor Example of an automation This demonstration shows you how to create an automation to turn on the Heating to 20 °C when the temperature is less than 18 °C. NOTE: It is mandatory to create two automations. First, switch on the heater at 22 °C when the room temperature is at 17 °C or lower. Second, switch off the heater when the room temperature is at 25 °C or above. The room heater will not turn off automatically until you create another automation. 1. Go to Automation > to create an automation. 2. To add a condition, tap Add Condition > Device status change > Temperature/Humidity Sensor > Temperature. 3. Set the temperature as 18 °C (A) and the condition as less than (B) and tap Set. Back Temp bedroom Set A ° B less than 4. Read the information and tap OK. 5. To add an action, tap Then > Add an action > Control a device > Heating > Setpoint. Set the temperature to 20 °C (C), then tap Set. Back Heating Set C 6. Read the information and tap OK. 7. Enter the name of the automation. TIP: You can choose the cover image that represents your automation by tapping . 18 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor 8. Tap Save. Once the automation is saved, it is visible on the Automation tab. Automations Schedules Device D NOTE: You can enable or disable saved automations on the Automations tab by using (D). DUG_Temperature and Humidity Sensor_WHP-01 19 Editing an automation Wiser Temperature/Humidity Sensor 1. On the Home page, tap Automations . 2. Go to Automation, tap the automation you want to edit. 3. On the Edit automation page, you can perform following changes: · Change the icon . · Rename the automation. · Tap each condition to change the settings. To remove a condition, slide the condition towards left and then tap (A) to delete it. Tap Add conditions (B) to add new condition. · To change the order of actions, tap the Then option, and hold an action then drag and drop to the desired position. Close Edit automation Save Living Room If When Conditions are met All conditions Then 1 of 10 Any condition A Close Edit automation Save If When Then Run these actions 3 of 10 You can move cards to choose the order of the actions. On Moment Wait Wait Activate 1 min 1 min Add conditions B Delete automation Add an action Delete automation 4. Tap Save to save the changes. Deleting an automation 1. On the Home page, tap Automations . 2. Go to Automation, tap the automation you want to delete. 20 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor 3. On the Edit automation page, tap Delete automation (A) and read the confirmation message and then tap OK (B). Close Edit automation Save Living Room If When Conditions are met All conditions Then 1 of 10 Any condition Are you Sure? Your Living Room automation will be deleted and can not be recovered. CANCEL OK B Add conditions Delete automation A Removing the device Using the Wiser Home app, you can remove the sensor from the Wiser system. To remove the sensor: 1. On the Home page, tap . NOTE: Please wake up the sensor (press the function key). 2. Tap Devices > Temperature/Humidity Sensor > Delete (A). TIP: Additionally, you can remove the Sensor from the Wiser system by tapping on the Home page Temperature/Humidity Sensor > Device settings > Delete (A). Device Details Temp/Humidity Sensor Battery OPTIONS Device Name Temperature/Humidity Sensory Location Living Room ABOUT Firmware Version 00.00.000y Identify Delete A 3. Read the confirmation message and tap Ok to remove the sensor from Wiser system on the next screen. NOTE: · Removing the sensor will reset the sensor. After resetting, the LED blinks amber indicating that the sensor is ready for pairing. · If there is a problem while pairing or resetting the sensor, refer to Resetting the device, page 23. DUG_Temperature and Humidity Sensor_WHP-01 21 Wiser Temperature/Humidity Sensor 22 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Resetting the device You can reset the sensor to factory default manually. 1. Remove the sensor from the base plate by sliding it upwards. 2. Short-press the function key 3 times (<0.5 s) and then long-press the function key once (>10 s), the LED blinks red after 10 s, and then release the function key. Upon successful reset of the sensor, the LED stops blinking. Then, the sensor restarts and blinks green for a few seconds. NOTE: After reset, the LED turns off to save the battery. 3× < 0,5 s + 1 x 10 s ... ×7 DUG_Temperature and Humidity Sensor_WHP-01 23 Replacing the battery Wiser Temperature/Humidity Sensor 1. Remove the sensor from the base plate by sliding it upwards. 2. Unscrew the battery cover using a screwdriver. NOTE: The screw is captive, after unscrewing from the primary part it remains attached to the cover. 3. Replace the battery with the proper polarity. 4. Re-install the battery cover and tighten the screw using a screwdriver. The LED blinks green seven times and then stops blinking. 5. Install the sensor on the base plate by sliding it down. NOTE: Dispose used batteries, as per statutory regulations. 1 2 5 ×7 4 3 LED indications Initial Stage Action Green LED blinks 7 times (1 Hz) LED Indication (7x) Status After the sensor is powered On for the first time or after the batteries were replaced. If not paired yet Action Amber LED blinks (1 Hz) Green LED is On for 3 seconds LED Indication (2 min) (3 sec) (3 sec) Status Indicates the pairing mode after function key is pressed 3 times within 1 second. If pairing is not successful, the amber LED is On for 3 seconds and then turns Off. Pairing was successful. If already paired Action Green LED blinks 5 times (1 Hz) An amber LED blinks for three seconds (4 Hz) LED Indication (5x) (3 sec) Status The sensor is paired and connected. The sensor is paired, but disconnected. Reset - After pressing the function key 3 times within 0.5 seconds and then hold for 10 seconds Action The red LED blinks for 10 seconds, remains on for 3 seconds, and then turns off. The sensor then restarts and blinks green for a few seconds. LED Indication (10 sec) (3 sec) 24 DUG_Temperature and Humidity Sensor_WHP-01 Wiser Temperature/Humidity Sensor Battery level LED Indication LED blinks amber once per minute. Status The battery is low (< 10%), replace the battery, page 24. NOTE: A notification pop-up will appear on the app. Troubleshooting Symptom The sensor triggers the automation/ schedule, but does not show the status on the app. LED blinks amber. Possible cause Solution The sensor may be undergoing an over-theair (OTA) firmware update. Wait for the firmware update to complete and then check that the sensor is reporting status. NOTE: The firmware update runs in the background. The sensor battery is low or drained. Replace the battery in the device, page 24 NOTE: A notification popup will appear on the app. Technical Data Battery Battery life Nominal power IP rating Operating frequency Max. radio-frequency power transmitted Operating temperature Temperature accuracy Temperature resolution Relative humidity Humidity accuracy Dimensions (H x W x D) Communication protocol Compliance RCM Safety EMC Radio EMR 3 VDC, CR2450 Up to 5 years (may vary based on the usage, frequency of firmware update and environment) 90 mW IP20 2405 2480 MHz 7 dBm -10 °C to 50 °C ±1.5 °C 0.1 °C 10 % to 95 % ±5 % 45 x 45 x 17.2 mm Zigbee 3.0 certified IEC 60730-2-9 EN IEC 60730-2-9 EN 300 328 EN 62479 DUG_Temperature and Humidity Sensor_WHP-01 25 Compliance Compliance Compliance information for Green Premium products Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product Environmental Profile (PEP) and End-of-Life instructions (EOLI). https://checkaproduct.se.com/ General information about Green Premium products Click the link below to read about Schneider Electric's Green Premium product strategy. https://www.schneider-electric.com/en/work/support/green-premium/ Trademarks This guide makes reference to system and brand names that are trademarks of their relevant owners. · Zigbee® is a registered trademark of the Connectivity Standards Alliance. · Apple® and App Store® are brand names or registered trademarks of Apple Inc. · Google PlayTM Store and AndroidTM are brand names or registered trademarks of Google Inc. · Wi-Fi® is a registered trademark of Wi-Fi Alliance®. · WiserTM is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies. Other brands and registered trademarks are the property of their respective owners. 26 DUG_Temperature and Humidity Sensor_WHP-01 Schneider Electric (Australia) Pty Ltd 33-37 Port Wakefield Road Gepps Cross SA 5094 Australia Customer Care: 13 73 28 www.clipsal.com As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication. © 2024 2024 Schneider Electric. All rights reserved. DUG_Temperature and Humidity Sensor_WHP-01