Parts List

Part List Diagram

Diagram showing parts labeled 1, 2, 3, 4.

Applicability:

• INT version: Model 3 (2017 - October 2020)
• AMD version: Model 3 (2021 - 2023.7), Model Y (2020 - 2025.2)
• Highland Model 3: (2023.8+)
• Model Y Juniper: (2025.3+)

Precautions: Tools required: Gloves. Installation precautions: Turn off the screen power for operation.

Tip: Read the instructions carefully for quicker installation.

Warnings and Disclaimers

Important notice: Welcome to purchase the company's products. Please read and understand the terms of this statement before using this product. Use of this product implies acceptance of all terms and conditions. The company reserves the right to update these documents. Please follow the instructions to operate this product.

Caution

1. Check whether the product list is complete and undamaged before installation.
2. The installation instructions may differ slightly from actual operation. Refer to the actual situation or contact customer service if differences occur.
3. Warning: Do not disassemble any parts yourself; improper operation will not be covered by the warranty.
4. Watch the installation video and instructions before installing the product.
5. Check if the installed product functions normally.
6. All models are common; installation procedures may vary slightly for different Tesla models. Please install according to actual conditions or contact customer service.

Customer Service: Phone: +1(626)412-7352, +1 7143179647. Email: service@tesstudio.com.

Resources: QR code linking to Installation Manual. QR code linking to Model 3/Model Y Installation Video. QR code linking to Highland Model 3/MY Juniper Installation Video.

Installation Instructions

Applicability:

• INT version: Model 3 (2017-2020.10)
• AMD version: Model 3 (2021-2023.7), Model Y (2020-2025.2)
• Highland Model 3: Applicable (23.8+)
• Model Y Juniper: Applicable (25.3+)

The installation method is as follows ⬇️

INT/AMD Version Installation

1. Remove the door edge strip and pry open the baffle. Image shows a hand using a plastic trim tool to pry open a door edge strip.
2. Pry open the snap. Image shows a hand prying a snap connector.
3. Remove the guard plate. Image shows a hand removing a plastic guard plate from the car interior.
4. Plug in the corresponding OBD power cord properly. Note: The INT version has only one plug. Image shows a hand plugging a wire harness into an OBD port.
5. Thread the wire. Pull the wrapped wire over. Image shows a hand guiding a wire harness through a car panel.
6. Connect the connecting wires properly, organize the wires, and cover the baffle. Image shows hands connecting multiple wire harnesses and tidying them up.
7. Find 3 centimeters away from the air outlet. Image shows a hand indicating a measurement point 3cm from a car's air outlet.
8. Break open the baffle a little and insert the light strip. Image shows a hand inserting a light strip into a small gap in a car panel.
9. Push it all the way along the air outlet, align the edges and press it in place. Image shows a hand pushing the light strip along the air outlet trim.
10. Effect after installation. Image shows the installed light strip glowing along the air outlet.

Highland/Juniper Version Installation

1. Find 3 centimeters away from the air outlet. Image shows a hand indicating a measurement point 3cm from a car's air outlet.
2. Tear off the adhesive tape and break the baffle a little. Image shows a hand peeling adhesive tape and prying a panel slightly.
3. Stick it all the way along the air outlet. Image shows a hand adhering the light strip along the car's air outlet.
4. Align along the edges and press to fix. Image shows a hand pressing the light strip to secure it along the edge.
5. When prying open one side of the baffle, there is no need to fully open it. Image shows a hand partially prying open a car panel.
6. Remove the door edge strip and pry open the baffle. Image shows a hand removing a door edge strip and prying open the panel.
7. Remove the door edge strip and pry open the baffle. Image shows a hand removing a door edge strip and prying open the panel.
8. Thread the wire. Pull the wrapped wire over. Image shows a hand guiding a wire harness through a car panel.
9. Connect the connecting wires properly, organize the wires, and cover the baffle. Image shows hands connecting multiple wire harnesses and tidying them up.
10. Remove the latch and find the connection socket. Image shows a hand removing a latch to access a wire connection socket.
11. Unplug the pin and connect our module back. Image shows a hand unplugging a connector and connecting a module.
12. Power-on test. Image shows a hand holding a connector for a power-on test.
13. Hide the lines well and reinstall them step by step. Image shows a hand tucking wires neatly into place.
14. Effect after installation. Image shows the installed light strip glowing along the air outlet.

Troubleshooting Guide

Warranty and Support

Tesstudio offers a 1-year extended warranty. Send your customer number to receive a full 1-year warranty.

Contact: Email: service@tesstudio.com. Our Website: tesstudio.COM.

Support: QR code linking to website and support information.