Instruction Manual for StingRay models including: STR-043 Implant Delivery System, STR-043, Implant Delivery System, Delivery System
Instructions for Use (IFU) - StingRay Medical
Implant Delivery system
Instructions for Use
DESCRIPTION The StingrayTM is a sterile flexible sheet used to assist in surgeries involving the placement of implants.
INTENDED USE StingrayTM is intended to facilitate implementation of a contact-free implant insertion. StingrayTM is intended to facilitate the delivery of silicone gel implants by providing a shell-tissue interface with less friction during insertion of the implant.
2
Fold to dotted line
Align implant he re Place implant in ci rcle
0
Hydrate befo re use Fold tail
3
Fold to dotted line
1
SYMBOLS
Sterilized by Ethylene Oxide
Date of Manufacture
Refer to Instructions for Use
Do Not Resterilize
55°C
5°C 131°F Temperature Range
41°F
Do not use device if the package has been opened or damaged
15% RH
WARNINGS
Use by Date
Manufacturer
Catalog Number
DO NOT Reuse
90% RH
Humidity Limitation
Not made with natural rubber latex
Caution
Keep Dry
Batch Code
DEHP Non-Phthalate
Rx Only Caution: Federal law restricts this device to sale by or on the order of a physician.
SINGLE USE. The product is intended for single patient use only. Depending upon implant type and insertion location, the device can be configured to be used for two insertions on the same patient in a single procedure.
STERILE PRODUCT
DO NOT USE IF PACKAGE HAS BEEN OPENED OR DAMAGED. The device is sterilized using Ethylene Oxide in sealed, double pouch packaging. Sterility is only maintained if the package seals are intact.
DO NOT RE-STERILIZE THE DEVICE. Re-use or re-sterilization shall not be performed under any conditions as contamination or infection may occur.
DO NOT USE DEVICE AFTER ITS "USE BY" DATE.
Always configure the device according to the implant type and insertion location prior to loading the implant to avoid damaging the implant.
Do not use excessive force when delivering the implant. Stop if the implant does not advance using moderate pressure. Confirm that the incision and the surgical pocket are clear of obstructions and are appropriately sized for the implant. Check that the device is not twisted or creased in a manner that could obstruct the implant.
Tested for use with silicone gel implants including, but not limited to, Sientra HSC 10621-700, Mentor SHPX-790, up to 790 cc.
Stingray Medical LLC 390 Commerce Drive, Woodbury, MN 55125 Phone: 612-500-7433
SR100
MADE IN USA
STR-043, Rev 12, 01/2024
GENERAL INSTRUCTIONS FOR USING THE STINGRAY TM
1. SET-UP
3. POSITION IMPLANT
A. Use approximately 60cc of saline solution or povidone-iodine prep solution for each implant and surgery site, depending on user preference.
B. Add approximately 30cc of the solution into the implant tray around the implant in the manner preferred.
C. AGITATE THE IMPLANT IN THE CONTAINER.
D. Unfold
Unfold the StingrayTM . Remove and
1
discard the top paper liner.
REPLACE STERILE GLOVES WITH A NEW PAIR.
AVOID TOUCHING THE INSIDE SURFACE OF THE DEVICE.
2
Fold to dotted line
Align implant he re Place implant in ci rcle
0
Hydrate befo re use Fold tail
3
Fold to dotted line
1
E. Hydrate
1
Using a sterile syringe or similar device, evenly distribute approximately 30cc of solution to wet the entire surface.
2
Fold to dotted line
Align implant he re Place implant in ci rcle
0
Hydrate befo re use
3
Fold to dotted line
Align implant he re Place implant in ci rcle
0
Hydrate befo re use
3
Fold to dotted line
A. Wrap tail ("1") Reach under tail and flip up tail flap labeled "1". Fold to top edge of implant.
AVOID TOUCHING THE INSIDE SURFACE OF THE STINGRAY DEVICE.
B. Wrap first side ("2") Fold over side flap. Fold to edge of implant.
C. Wrap second side ("3") Fold over other side flap. Fold to edge of implant.
THE TONGUE SHOULD FORM A ROUNDED CHANNEL AS SHOWN.
2. PLACE IMPLANT
2
Fold to dotted line
Align implant he re Place implant in ci rcle
0
Hydrate befo re use Fold tail
3
Fold to dotted line
1
Align top edge of implant here
Fold to edge of implant
Fold to edge of implant
Hydrate before use
A. Place Implant ("0") Gently place implant on target spot labeled "0".
B. Align Implant Align top of implant with guidelines as indicated, keeping implant centered between the diagonal dotted fold lines. NOTE ORIENTATION OF IMPLANT FACE UP OR FACE DOWN
TROUBLESHOOTING
Problem: The sheet opened up during implant delivery. Solution: Re-wrap the sheet by following instructions and ensure that a firm grip is maintained through implantation.
4. DELIVER IMPLANT
A. Rotate device as needed to orient implant correctly and agitate back and forth a few times to ensure implant & distal end is saturated with solution. B. Insert tongue into incision. C. Deliver Manipulate and deliver the implant by applying pressure behind the implant and pushing it forward.
Problem: The implant will not move without excessive force. Solution: Make sure the entire surface of the StingrayTM is completely saturated with solution especially the wings, tail, and distal end.
Adobe PDF library 17.00