iScooter i8M & i9M User Manual

Package Contents

The package includes the following items:

• Scooter
• Charger
• Stem Bolt x6 (Including 2 Spare Bolts)
• Hex Wrench

Product Overview

The diagram shows an electric scooter with various parts labeled with numbers 1 through 15. The components are:

• 1. Headlight
• 2. Bell
• 3. Brake Lever
• 4. Folding Buckle
• 5. Display
• 6. Throttle
• 7. Stem
• 8. Folding Latch
• 9. Charging Port
• 10. Kickstand
• 11. Deck
• 12. Hook
• 13. Rear Fender
• 14. Taillight & Brake Light
• 15. Disc Brake

Quick Setup / Assembly

Follow these steps for initial setup:

1. Raise the stem to the riding position and close the folding latch until you hear a click.
2. Install the handlebar assembly onto the stem. Pre-tighten all four bolts, then fully tighten them using the supplied hex wrench.

The diagram illustrates these assembly steps.

Folding the Scooter

To fold the scooter:

1. Turn the scooter off.
2. Open the folding latch.
3. Fold down the stem.
4. Ensure the folding buckle on the handlebar catches the hook on the rear fender.

The diagram shows the folding sequence.

Unfolding the Scooter

To unfold the scooter:

1. Press the folding buckle to release the handlebar from the rear fender.
2. Lift the stem to the riding position.
3. Close the folding latch until you hear a click.

The diagram illustrates the unfolding process.

About Charging

The scooter is fully charged when the charger indicator changes from red to green. The scooter features charging protection, automatically stopping the charge after a full charge. However, leaving it to overcharge is not recommended. Keep the charging port cover closed when not charging.

Display Information

The display shows various indicators:

• 1. Real-time Speed: Displays the current speed.
• 2. Speed Unit: Shows the speed unit, either km/h or mph.
• 3. Riding Mode: Indicates the current riding mode (e.g., ECO, D, S).
• 4. Headlight & Taillight: Shows the status of the front and rear lights.
• 5. App Connected: Indicates if the scooter is connected to the mobile app.
• 6. Motor Overheating: Warning indicator for motor temperature.
• 7. Battery Level: Displays the remaining battery charge.
• 8. Cruise Control: Indicates if cruise control is active.
• 9. Error Code: Displays error codes if any issues occur.

Riding Modes and Maximum Speed

i8M

i9M

Error Codes

If you see an error code listed on the display, please contact customer support to resolve the issue.

Power Button Functions

• Turn On/Off: Press and hold the Power button to turn the scooter on or off.
• Lights: Press the Power button to turn the headlight and taillight on or off.
• Riding Modes: Double-press the Power button to cycle through the riding modes.
• Speed Unit: Press the Power button three times to switch between km/h and mph.
• Start Mode (Zero/Non-zero): Press the Power button four times to switch between zero start and non-zero start.
• Cruise Control: Press the Power button five times to enable or disable cruise control.

Note: The scooter will automatically shut down if there is no operation for 10 minutes. When cruise control is turned on, maintaining a speed for 5 seconds will engage it, allowing the scooter to move forward at that speed without applying the throttle.

Specifications

i8M Specifications

i9M Specifications

Range and Load Capacity Details

* About the range: Measured under the condition of 100% battery level, a load of 70 kg (154 lbs), and a speed of 15 km/h (9 mph). The range will differ depending on different factors, such as load, humidity, wind speed, and operation habits.

* The structure of this scooter is designed to support a maximum load of 120 kg (264 lbs). For the best riding experience, 70% of the maximum load is recommended.

Compliance and Safety Information

FCC ID: 2BBGK-19M. This equipment has been tested and found to comply with the limits for Class B digital devices, in alignment with section 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ISED Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

CE Warning: This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to ensure they do not play with the appliance.

Declaration of Conformity: For the full text of the EU Declaration of Conformity, visit: https://www.iscooterglobal.de/pages/konformitatserklarung

Disposal of Electrical and Electronic Equipment: The crossed-out garbage can symbol indicates that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. Batteries must be removed and disposed of separately.

Tuya Smart App and Customer Service

Install the "Tuya Smart" App to enhance your riding experience. Download the app by scanning the QR code or searching "Tuya Smart" on the App Store (iOS) or Google Play Store (Android).

Customer Service: Contact us if you experience issues relating to riding, maintenance and safety, or errors/faults with your electric scooter.

• US: www.iscooterglobal.com, support@iscooterglobal.com, +1 888 4968123
• FR: www.ihoverboard.fr, support@ihoverboard.com, +33 805980335
• UK: www.iscooterglobal.co.uk, support@iscooterglobal.co.uk, +44 1888 785356
• DE: www.iscooterglobal.de, support@iscooterglobal.de, +49 800 0003728

Manufacturer: Shenzhen Xincheng Times Technology Co., Ltd

EC REP: GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA

UK REP: Sea&Mew Accounting Ltd