Netstor TechnologyNetstor Technology
User Manual for netstor models including: NS388P, NP980A-G4, NS388P Host Card, NS388P, Host Card, Card
9 апр. 2025 г. — User Manual. NS388P. NP980A-G4 host card. Page 2. Headers/Connector. Side-band modes selection. 3. 4. LEDs' Definition. 6. Ports' connecting sequence between.
LED7 PCIe switch heartbeat LED Blinking: Indicates PCIe switch loading firmware successfully and working correctly Color Blue LED8 System health LED 0.5Hz blinking when system is good 2Hz blinking when any failure event detected, e.g. voltages, fan, and temp failed Green LED 5/4/ 3/2 Link matching LED for SFF-8674 connectors Case 1: set in mode 1, 5 or 9 LED5 lights when SFF-8674 ports not ...
File Info : application/pdf, 8 Pages, 14.98MB
DocumentDocumentNS388P NP980A-G4 host card User Manual First edition, Apr. 2025 Headers/Connector 3 Side-band modes selection 4 Bifurcation modes selection 5 LEDs' Definition 6 Ports' connecting sequence between enclosure and host card 8 Headers/Connector CN16 J7 J3 CN9 CN1 J6 Headers Description Pinout ON: Force PCIe switch to enter boot recovery 1 J6 OFF: PCIe switch loading default FW image as normal operation (default) CN1 ON: Force PCIe switch to enter boot recovery 1 TX/RX/GND OFF: PCIe switch loading default FW image as normal operation (default) CN9 Micro-USB port for executing uP CLI commands ON: uP in firmware upgrading mode J7 OFF: uP in normal operation mode (default) CN16 Reserved I/F for uP firmware debugging UART with 3.3V TTL signals level TX/RX/GND ON: ISP mode for uP firmware programming J3 OFF: uP in normal operation (default) 3 Go Top Side-band modes selection S2 POS 2 | 3 Description Target mode, and select Side-band mode to PCI-SIG for SFF-8674 connectors Host mode, and select Side-band mode to PCI-SIG for SFF-8674 connectors Host mode, and select Side-band mode to SC for SFF-8674 connectors 4 Go Top Bifurcation modes selection S2 S2 POS1 S1 S2 POS 1 S1 POS 1 | 2 | 3 Mode Host/Target Description 1 SRNS: Set SFF-8674 to one x16 link 2 SRNS: Set SFF-8674 to Two x8 link 3 SRNS: Set SFF-8674 to Four x4 link 4 SRNS: Set SFF-8674 to Eight x2 link Host 5 SRIS: Set SFF-8674 to one x16 link 6 SRIS: Set SFF-8674 to Two x8 link 7 SRIS: Set SFF-8674 to Four x4 link 8 SRIS: Set SFF-8674 to Eight x2 link 9 Target SRIS: Set SFF-8674 to one x16 link 5 Go Top LEDs' Definition LED8 LED7 LED5 LED4 LED3 LED2 6 Go Top Location Color Definition LED7 Blue PCIe switch heartbeat LED Blinking: Indicates PCIe switch loading firmware successfully and working correctly LED8 Green System health LED 0.5Hz blinking when system is good 2Hz blinking when any failure event detected, e.g. voltages, fan, and temp failed LED 5/4/ 3/2 Red Link matching LED for SFF-8674 connectors Case 1: set in mode 1, 5 or 9 LED5 lights when SFF-8674 ports not linking at x16 Case 2: set in mode 2 or 6 LED5 and LED3 light when SFF-8674 ports not linking at x8 Case 3: set in mode 3, 4, 7 or 8 LED5, LED4, LED3 and LED2 light when SFF-8674 ports not linking at x4 or 2x2 7 Go Top Ports' connecting sequence between enclosure and host card 1 2 Host Card 1 3 4 2×2 backplane & 1×4 backplane NS388P enclosure and host card connection diagram. Enclosure's port 1 should be connected to host card's port 1, and then subsequently until enclosure's port 4 connecting to host card's port 4. If you have any questions, please contact your regional distributor, or Netstor Technology, Taiwan. Netstor Technology Co. Ltd. 6F, No. 1, Alley 16, Lane 235, Baoqiao Rd., Xindian District, New Taipei City 231-45, Taiwan, R.O.C. www. netstor. com .tw sales@ netstor.com.tw +886 2 2917 1500 8 Go Top