User Manual for CYBER DRONE models including: 2BN3D-CYBERLIGHT, 2BN3DCYBERLIGHT, CYBERLIGHT Drone Camera with Controller, CYBERLIGHT, Drone Camera with Controller, Camera with Controller, Controller, Drone
CYBER DRONE CO LLC. CYBERLIGHT Cyber Light 2BN3D-CYBERLIGHT 2BN3DCYBERLIGHT cyberlight
CYBERLIGHT User Manual V1.0 2020.11 Contents Introduction ........................................................................... 3 Drone diagram.....................................................................4 Remote controller diagram......................................... 5 Charger diagram ................................................................ 6 Flight preparation .............................................................. 7 Flight ...........................................................................................8 Maintenance storage and disposal......................10 Specification and support ........................................... 11 © CyberDrone Ltd 2 Introduction The Cyberlight is a fast and extended flight time drone with high accuracy performance to ensure stability during the drone light show. Unparalleled production In-house drone, better throttle control, and smoother motion. Long duration A 20-minute drone show instead of 10 minutes. Lightweight 285g drone obtain powerful rotors that provide the best balance of efficiency. High stability and accuracy Dual-frequency global navigation, high-resolution animations, and flight stability. Brighter than ever 18 watts LED in all direction, a better LED lighting efficacy. © CyberDrone Ltd 3 Drone diagram 1. Navigation antenna GPS/GLONASS/GALILEO /BEIDOU 2. Motors 3. Frame 4. Propellers 5. LED lighting system 6. Battery © CyberDrone Ltd 4 Remote controller diagram 1: Antenna (if equipped with RF Module) 2: Handle 3: SWC three-segment switch 4: SWH two-segment switch 5: SWD three-segment switch 6: AUX5 knob 7: RF indicator 8: Throttle / Aileron 9: Power switch 10: Digital trim key 11: Digital trim key 12: Menu direction key 13: Display Screen 14: Exit key 15: Confirm key 16: Digital trim key 17: Digital trim key 18: Direction / Tilt Joystick 19: Power Indicator 20: AUX4 Knob 21: SWA three-segment switch 22: SWG two-segment switch 23: SWB three-segment switch 24: Loud Speaker Bay 25: Battery Bay 26: TF Memory card slot 27: JR/FrSKY Module (included with T12+JP4-in-1 combo only © CyberDrone Ltd 5 Charger diagram 1: Charher (Input voltage: 100v240v AC) 2: Battery Adapter 3: Battery 4: Plug 5: Power cord 5 © CyberDrone Ltd 6 Flight preparation · Fully charge the drone battery. Do not leave the battery connected to the charger unattended · Insert the battery into the compartment at the bottom of the quadcopter, gently pushing the battery until bumping. · Switch on the remote controller. Press power button and hold it down until the screen is turned on. The battery level will be shown on the upper right corner of the screen. Make sure that the battery level is sufficient to complete the flight. · The Cyberlight equipped with powerful motors and sharp spinning propellers. Please exercise caution when working on it and keep it in sight. Ensure power of remote controller is disconnected from the Cyberlight and remove propellers when performing maintenance. · Do not operate the system under the follow conditions: · Do not operate the remote controller radio system under the follow conditions. · During bad weather or high wind conditions such as rain, hail, snow, storms or electromagnetic events. · During any conditions of limited visibility. · In areas where people, property, powerlines, roads, vehicles or animals may be in present. · If the radio or model appear to be damaged or not functioning correctly. · In areas of high 2.4ghz interference or in locations where use of 2.4ghz radios is prohibited. · When the battery is the T12 or the model is too low to function. © CyberDrone Ltd 7 Flight 1. Start: move the left throttle to the right and left, and hold it in this position until the propellers start. 2. Perform the flight, controlling the quadcopter by sticks and mode switch. © CyberDrone Ltd 8 3. After landing, stop the propellers by moving the left throttle to the left and down, and hold it in this position until the propellers stop. 4. After completing the flight, carefully unplug the battery from the drone. 5. Switch off the remote controller. Press power button and hold it down until the remote controller unit screen has turned off. © CyberDrone Ltd 9 Maintenance, storage and disposal Drone · Remove the battery from the drone before storage. · Keep the drone in a dry place, away from heat sources, in a package that prevents mechanical damage. · Keep the original packaging for convenient transportation and storage. · The product contains electronic components and chemical power supplies. The components of the product at the end of service life should be disposed of in accordance with local legislation. Battery and charger · The battery must stay in the operating temperatures outlined in its data sheet · The battery must not exceed voltage, current, and other ratings in its data sheet · Be careful not to short-circuit · Store batteries separately, and do not transport without proper packaging · Never store or transport together with conductive or metallic objects particularly in a pocket or bag · Do not keep in the sun, in a hot car, or anywhere with direct heat · If you notice an unusual odor, rust, can deformation, damaged surface, or fluid discharge, especially on first use, discontinue use and contact our hotline · Keep the battery away from animals and children · If the battery is attached to a PCB, keep it away from high-static environments · When nominal capacity after full discharge cycle is less than 80% of rated capacity, please discontinue use · Recycle discontinued batteries according to local regulations and cover terminals with insulating tape before disposal © CyberDrone Ltd 10 Specification and support Drone Type Multi-rotor Flight time Up to 30 minutes Takeoff weight 285g Dimensions 100mm 150mm 150mm Operating temperature 0 °C - 40 °C Air speed Up to 60 m/h Flight altitude Up to 1000 m Engine Electric brushless motors Remote controller Size 158mm 150mm 52mm Weight 342g Working voltage DC5-DC9V (factory with 4 * AA battery box, 2s Lipo recommended, batteries not included) Firmware OpenTX Channels Up to 12 channels Display 1.7-inch LCD display, 128* 64 resolution Simulator mode Potentiometer Battery Voltage, charge max. Voltage, nominal Voltage, discharge end Capacity Energy 12.6V 11.1V 7.5V 3000 mAh 33.3Wh © CyberDrone Ltd 11 Operating temperature Storage temperature Humidity 0 °C - +45 °C -20 °C - +35 °C 15% - 65% Support Please retain your proof of purchase and contact us. Email: info@cyberdrone.show FCCWarning 15 .19 Labelingrequirement s. This device complies with part 15 of the FCC Rules. Operation is subject to thefollowingtwoconditions: (1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust accept any interference received, including interference that may causeundesiredoperation. 15 .2 1 Inf ormat ion t ouser. Any Changes or modifications not expressly approved by the party responsibleforcompliance could void the user's authority to operate theequipment. 15 .10 5 Inf ormat ion t o t heuser. Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovidereasonable protection against harmful interference in a residential installation.Thisequipment generates uses and can radiate radio frequency energy and, if notinstalledand used in accordance with the instructions, may cause harmful interference toradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular installation. If this equipment does cause harmful interference to radioortelevisionreception, whichcanbedeterminedbyturningtheequipmentoffandon, theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures: -Reorient or relocate the receivingantenna. -Increase the separation between the equipment andreceiver. -Connect the equipment into an outlet on a circuit different from that to which thereceiverisconnected. -Consult the dealer or an experienced radio/TV technician forhelp. FCC RF Radiat ion ExposureSt at ement : 1. ThisTransmittermustnotbeco-locatedoroperatinginconjunctionwithanyotherantenna ortransmitter. 2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. © CyberDrone Ltd 12macOS 版本10.15.7（版號19H2） Quartz PDFContext Word