IEEE 802.11a-1999 - WikipediaIEEE 802.11ac-2013 - WikipediaIEEE 802.11g-2003 - Wikipedia
en:users:drivers:ath10k [Linux Wireless]
Making sure you're not a bot!
Instructions for DOODLE Labs models including: ACM-DB-2M, ACMDB2M, 2AG87ACM-DB-2M, 2AG87ACMDB2M, ACM-DB-2M Radio Transceivers, ACM-DB-2M, Radio Transceivers
Doodle Labs (SG) Pte Ltd ACM-DB-2M Wi-Fi Radio Transceiver 2AG87ACM-DB-2M 2AG87ACMDB2M acm db 2m
File Info : application/pdf, 7 Pages, 742.20KB
DocumentDocumentACM-DB-2M Rugged/Military grade 2.4/ 2x2 MIMO Wi-Fi® Radio Transceivers Features · Qualcomm-Atheros QCA9890-BR4B Chipset with Extended Temperature Range · Up to 1.3 Gbps Throughput with 3x3 MIMO Technology · Calibrated High Power 2.4 GHz (29 dBm) afor Extended Range · 802.11 Dynamic Frequency Selection (DFS) in AP and Client mode · Supported by OpenWRT and Ath10k Open-Source Driver · MiniPCIE Interface Installation and Usage The ACM-DB-2M has been FCC certified for indoor usage with Superbat 3-dBi rubber-duck antennas (WA2-1321-S02SP1-030 in the 5-GHz bands, and WA2-995-S02SP1-030 antennas in the 2.4GHz band). The ACM-DB-3 mates with a standard PCIE-mini slot and integrates with the Ath10k software driver which is preinstalled in Linux-based systems. TECHNICAL SPECIFICATIONS Model No. MAC Chipset Software Support ACM-DB-2M(Rugged/Military Applications, 802.11ac) QCA9890-BR4B with Extended Temperature range for Outdoor and Rugged models) Open Source Linux Driver ath10k OpenWRT (Wireless Router/Linux OS) Center Frequency Range Channel Bandwidth/(No. of Nonoverlapping Channels)* Radio Modulation (Auto Adjust) 2.412 GHz ~ 2.484 GHz This varies by the regulatory domain 20/(27), 40/(13) and 80/(6) MHz channels (5.x GHz) 20/(3), and 40/(1) MHz channels (2.4 GHz) BPSK, QPSK, 16 QAM, 64 QAM and 256 QAM (5.x GHz 11ac models) CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz 11ac models) Data Rates Supported 802.11ac Wave 1 Capabilities 802.11n: MCS0-23 (5.x and 2.4 GHz) 802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz) Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal ratio combining (MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK, 802.11e compatible bursting, Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check (LDPC), Space Time Block Code (STBC) Phy data rates up to 1.3 Gbps (80 MHz channel) Operating Modes MAC Protocol Wireless Error Correction Wireless Data Security FIPS Certification Tx/Rx Specification AP, STA and Adhoc modes to implement Point to Point, Point to multi Point, and Mesh networks TDD with Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) FEC, ARQ 128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for IEEE 802.11d, e, h, i, k, r, v, w and time stamp standards Loop back mode to facilitate FIPS AES certification, Small packet size (96 bytes) in AES encryption at full packet rate Data Rate Radio Modulation Throughput** Mbps (Cabled Test Setup) Max Tx Power (± 2 dBm) 3 Antennas Rx Sensitivity (± 2 dBm) 3 Antennas 2.4 GHz (20 MHz Channel) 802.11b, Single Stream, STBC 1 Mbps CCK 0.8 802.11g, Single Stream, STBC 6 Mbps BPSK 5.5 802.11g, Single Stream, STBC 24 Mbps 16 QAM 18 802.11g, Single Stream, STBC 36 Mbps 16 QAM 24 802.11g, Single Stream, STBC 48 Mbps 64 QAM 31 29 -100 29 -98 29 -90 27 -87 26 -84 802.11g, Single Stream, STBC 54 Mbps 64 QAM 32 26 -82 802.11n, HT20, 3 Streams MCS16 BPSK 18 29 -92 802.11n, HT20, 3 Streams MCS18 QPSK 54 29 -86 802.11n, HT20, 3 Streams MCS20 16QAM 108 27 -79 802.11n, HT20, 3 Streams MCS22 64 QAM 162 24 -75 802.11n, HT20, 3 Streams MCS23 64QAM 189 24 -74 2.4 GHz (40 MHz Channel) 802.11n, HT40, 3 Streams MCS16 BPSK 36 29 -87 802.11n, HT40, 3 Streams MCS18 QPSK 108 29 -80 802.11n, HT40, 3 Streams MCS20 16QAM 216 26 -74 802.11n, HT40, 3 Streams MCS22 64 QAM 470 24 -70 802.11n, HT40, 3 Streams MCS23 64QAM 486 23 -68 * It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller Bandwidths provide more channels to choose and help avoid interference issues. The system's SNR is higher at smaller Channel Bandwidths and Range is longer. ** Throughput of a wireless link depends on many environmental parameters. Here the bench measurement results are shown to give an indication of the real life performance of Doodle Labs modules. These results are lower than the theoretical values published in most of the literature. They do not include distance related derating. Antenna Signal Strength -50 to -90 dBm (Recommended), Absolute Maximum=+12 dBm Antenna port isolation for concurrent operation Up to +5 dBm signal strength for 2.4 GHz signal without degrading 5.x GHz operation Integrated Antenna Port Protection >12 KV (Human Body Model) for Outdoor and Rugged models (ACO/ACM-DB-3 and NO/NMDB-3) Receiver LNA Gain >12 dB Receiver Adjacent Channel Rejection (ACR) >28 dB @6 Mbps, 13 dB @54 Mbps, 3 dB @ VHT80, MCS9 Receiver Next to Adjacent Channel Rejection (ALCR) >40 dB Receive chain Noise Figure +5 dB Transmitter Adjacent Channel Leakage power Ratio (ACLR) Min 45 dB (Fc ± ChBW) Transmitter Spurious Emission Suppression -40 dBc (Minimum) RF Power control by Driver In 0.5 dBm steps. Accuracy of power calibration ±2 dBm RF Hardware Disable Pin 20 of miniPCI-E interface. (Required for FAA compliance) Control for External Power Amp Available as an optional configuration Spectral Analysis 8 bit resolution spectral FFTs available for software analysis PHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONS Antenna Ports 3 Ports (50 Ohms) with MMCX connectors. Optional configuration with U.FL connectors available on request Host Interface miniPCI-Express 1.2 Standard Host CPU Board Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm connector height Operating Voltage 3.3 Volts from miniPCI-Express connector Power Consumption 5W @ Max power, in continuous data transfer mode on all 3 chains 3.5W @ 25 dBm power, in continuous data transfer mode on all 3 chains 2.5W @ 20 dBm power (ETSI max), in continuous data transfer mode on all 3 chains 0.9W in continuous data receive mode 250 mW in Sleep mode Shield case temperature range (Operating) 0°C to +60°C (Enterprise/Indoor "*E-DB-3" models) -40°C to +60°C (Outdoor "*O-DB-3" models) -40°C to +80°C (Rugged "*M-DB-3" models) The System's thermal design should ensure that the transceiver's case temperature is maintained within these specifications. Humidity (Operating) 0% 95% (Non-condensing) Dimensions 30 x 50 x 7 mm, 14 grams (Rugged models). Mechanical drawing and 3D-CAD files available upon request Regulatory Requirements Designed and Verified to meet various regulatory requirements. Formal testing and approval is required based on the Integrator's particular host platform and antenna type. The Integrator is also responsible for obtaining all required regulatory approvals in target markets for the finished product. FCC ID 2AG87ACM-DB-2M CE/ETSI 11ac models in AP and Client modes with full DFS in conformity with all the requirements of the European Directive 1999/5/EC EN 301 893 V1.8.1, EN 300 328 V.1.8.1, EN 301 489-1 V1.9.2, EN 301 489-17 V2.2.1, EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011+ A2:2013 Industry Canada (IC) 21411-ACMDB2M RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 External antenna with gain ANT0: 7dBi, ANT1: 7dBi FCC Regulatory Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If power exceeds the limit and the distance(Over 20cm distance in actual use between the device and user) is compliance with the requirement RF Exposure Compliance: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Notice to OEM integrator If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The end product shall haves the words "Contains Transmitter Module FCC ID: 2AG87ACM-DB-2M". The device must be professionally installed. The intended use is generally not for the general public. It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. The user has no access to the connector. Installation must be controlled. Installation requires special training. Any company of the host device which installs this modular with unlimited modular approval should perform the test of radiated & conducted emission and spurious emission, etc. according to FCC part 15C: 15.247 and15.209 & 15.207, 15B Class B requirement, only if the tests result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B Class B requirement, then the host can be sole legally. When the module is installed inside another device, the user manual of the hose contain below 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation IC statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic DevelopmentCanada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences etDéveloppement économique Canada. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de brouillage,et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme auxCNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1)L'appareil ne doit pas produire de brouillage; 2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then theoutside of the device into which the module is installed o display a label referring to the enclosed module. This exteriorlabel can use wording such as the following: "Contains IC:21411-ACMDB2M" any similar wording that expresses the same meaningmay be used. l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots «Contient un module d'émission », du mot « IC:21411-ACMDB2M» ou d'une formulation similaireexprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 andcompliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure andcompliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'expositionde RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet équipementdevrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. Singapore: Doodle Labs (SG) Pte. Ltd. 150 Kampong Ampat KA Center, Suite 05-03 Singapore 368324 Tel: +65 6253 0100 USA: Doodle Labs LLC 2 Mattawang Drive Somerset, NJ 08873 Tel: +1 862 345 6781 Fax: +65 6353 5564