Lynk Inc - Lynk Inc
Installation Guide for LYNK PROFESSIONAL models including: SELECT Pull Out Cabinet Organizer, SELECT, Pull Out Cabinet Organizer, Out Cabinet Organizer, Cabinet Organizer, Organizer
LYNK PROFESSIONAL SELECT™ Pull Out Cabinet Organizer - 14" x 21" - Slide Out Drawers for Kitchen Cabinets - Sliding Pantry Shelves - Roll Out Shelf for Pots, Pans, Lifetime Ltd Warranty - 2 Tier : Home & Kitchen
File Info : application/pdf, 2 Pages, 1.49MB
DocumentDocumentSelect TM Under Sink Spice Rack Installation Unpack Discard 4 packing clips Rods Qty 2 Discard 8 packing clips Lower Upper Parts Wood Floor Wood Floor Bag #1 Small Wood Screw (8) Brackets (4) #2 Large Wood Screw (4) Front Glide Frame Lower Drawer Top Drawer Wood Fronts Qty. 2 Lower Top Wood Front Wood Front #3 Mounting Screw (4) Instructions and Alignment Guide Tools Needed Pencil 3/32" Drill Bit Power Drill Phillips Screwdriver Tape Measure Decide How To Position The Organizer In Your Cabinet Top Drawer on the Left or Top Drawer on the Right Choose Either Left - OR - Right Installation (shown below) Left Right 1 Insert rods into lower drawer until firmly in place (2 rods) 1 Insert rods into lower drawer until firmly in place (2 rods) Rod Rod Lower Drawer Lower Drawer Front 2 Slide drawer onto tops of 2 rods until top drawer is firmly in place Top Drawer Rod Front 2 Slide drawer onto tops of 2 rods until top drawer is firmly in place Top Drawer Rod Front Front 3 Align glide frame in left side of cabinet using alignment guide 3 Align glide frame in right side of cabinet using alignment guide Make sure arrows are pointing forward Make sure arrows are pointing forward 2.5"min. 63.5mm 2.5"min. 63.5mm Glide Frame Alignment Guide 2.5"min. 63.5mm Next Page Glide Frame Alignment Guide 2.5"min. 63.5mm 2.5"min. 63.5mm 2.5"min. 63.5mm Next Page LIFETIME LIMITED WARRANTY AND DISCLAIMER OF LIABILITY Lynk® will, for the life of the product, at its option, repair or replace, free of charge, any part of the equipment that is defective in material or workmanship or both, providing that installation and use of the equipment complies with the instructions in the instruction manual. For warranty service, please call Lynk® at 1.800.733.5965 or email lynkinc@lynkinc.com.This warranty does not cover damage due to misuse, abuse or normal wear and tear, and seller shall have the right to request that the product be shipped for inspection at buyer's expense. THERE ARE NO OTHER EXPRESS WARRANTIES OR IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ABOVE WARRANTY IS LIMITED TO THE ORIGINAL PURCHASER. ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED AND LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. BUYER'S SOLE REMEDY IS THE LIMITED WARRANTY STATED ABOVE. DEPENDING ON THE LAW OF THE STATE WHERE YOU LIVE, THIS EXCLUSION OF ALL IMPLIED WARRANTIES AND OF INCIDENTAL AND CONSEQUENTIAL DAMAGES MAY NOT APPLY TO YOU. The warranty period begins on the date of purchase by the original retail consumer or end user. US Patents 7,810,890 and D889,891 If you have questions, Call 800-733-5965 lynkinc.com 11x18 Under Sink Wood Drawer - #425118DS R2 © 2023 Lynk, Inc. 8241 Melrose Dr. Lenexa, KS 66214 Page 1 Continued, Top Drawer on Left 4 Temporarily set drawer onto glide frame with mounting holes aligned Check for adequate cabinet & door clearance Adjust glide frame position if needed Continued, Top Drawer on Right 4 Temporarily set drawer onto glide frame with mounting holes aligned Check for adequate cabinet & door clearance Adjust glide frame position if needed Clearance Mounting Holes (4 places) Clearance Mounting Holes (4 places) Front 5 Remove drawer from glide frame Move inner glide rails forward Mount glide frame to cabinet #2 Large Wood Screw (4) Do not over tighten Recommended: Drill 4 starter holes using a 1/8" diameter drill bit Use of a Power Screwdriver Install front screws then back screws Inner Glide Rail Forward Front 5 Remove drawer from glide frame Move inner glide rails forward Mount glide frame to cabinet #2 Large Wood Screw (4) Recommended: Drill 4 starter holes using a 1/8" diameter drill bit Use of a Power Screwdriver Install front screws then back screws Inner Glide Rail Forward Do not over tighten 6 Attach wood to front of lower drawer as shown #1 Small Wood Screw (4) Brackets (2) Do Not Overtighten Front Bracket & Wood Mount Holes Aligned No packing clips 7 Attach wood to front of top drawer #1 Small Wood Screw (4) Brackets (2) Do Not Overtighten 6 Attach wood to front of lower drawer as shown #1 Small Wood Screw (4) Brackets (2) No packing clips Do Not Overtighten Front Bracket & Wood Mount Holes Aligned 7 Attach wood to front of top drawer #1 Small Wood Screw (4) Brackets (2) Do Not Overtighten Front Bracket & Wood Mount Holes Aligned 8 Mount drawer onto glide frame with mounting holes aligned #3 Mounting Screw (4) Bracket & Wood Mount Holes Aligned Front 8 Mount drawer onto glide frame with mounting holes aligned #3 Mounting Screw (4) Do Not Overtighten Do Not Overtighten Front 9 Insert wood floors (2 places) Front 9 Insert wood floors (2 places) If you have questions, Call 800-733-5965 Page 2