Havit Lighting
Installation Guide for HAVIT Lighting models including: HV3288W-AB, HV3288C-AB, HV3288W-BR, HV3288C-BR, HV3288W-GPH, HV3288C-GPH, HV3288W-BLK, HV3288C-BLK, HV3288W-WHT, HV3288C-WHT, HV3288W-SS316, HV3288C-SS316, HV3288W-AB Stylez Step Light, HV3288W-AB, Stylez Step Light, Step Light, Light
HV3288-AB - Stylez Antique Brass LED Step Light – Havit Lighting
File Info : application/pdf, 1 Pages, 143.36KB
DocumentDocumentStylez Step Light Installation Instructions Model No. Name Material Colour IP Rating Input Voltage Lamp Base Lamp Wattage Colour Temp Lumens -HV3288 CRI Dimmable Warranty HV3288W-AB HV3288C-AB Antique Brass 3000k 240lm 5500k 250lm HV3288W-BR HV3288C-BR Brass Brass 3000k 240lm 5500k 250lm Product Specifications HV3288W-GPH HV3288C-GPH HV3288W-BLK HV3288C-BLK HV3288W-WHT HV3288C-WHT HV3288W-SS316 HV3288C-SS316 Stylez 316 Stainless Steel Graphite Black White Stainless Steel IP65 12v DC Built in LED 1x 3w 3000k 5500k 3000k 5500k 3000k 5500k 3000k 5500k 240lm 250lm 240lm 250lm 240lm 250lm 240lm 250lm > 80 No 3 Years Replacement* Dimensions Mounting Base Diagram 9 53 15 15 2x (4X10) 23 69 Important Safety Issues: · This product must be installed by a qualified electrician according to AS/NZS 3000. · Ensure all electrical mains are disconnected before any installation. · Modification of this product will void any warranty. · Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system. · When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided. · When installing copper or brass fittings, gloves must be worn to avoid any oils transferring to fitting. · All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining) · All o-rings and seals must be in place correctly to maintain warranty. · These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions. Steps for Installation: 1. Make sure that the electrical circuit is free of voltage (master switch off ) 2. Remove base plate from fitting by loosening allen screws on side of fitting. 3. Install mounting bracket in desired location. 4. Using an appropriate 12v DC LED Driver - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V 5. Connect the cable - If more than one fitting installed, wiring must be done in parallel. 6. Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together 7. Solder all joins using solder and either a heat gun or butane gas torch. 8. Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty. 9. Heat the heat shrink or crimp the gel cap making sure all connections are covered. 10. Reattach fitting to base plate making sure allen screws are tight to avoid water penetration 11. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections. 12. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit. Contact Details: 143 Beauchamp Road Matraville NSW 2036 Australia Must be installed by a licensed electrician Warranty Terms & Conditions* Tel: 02 9381 8300 Fax: 02 9666 8881 Email: sales@havit.com.au Web: www.havit.com.au Additional Information