Lightcloud
Lightcloud by RAB - The World's most powerful lighting control system.
Lightcloud by RAB - The World's most powerful lighting control system.
Instruction Manual for Lightcloud models including: LCCONTROL20 D10, Controller, LCCONTROL20 D10 Controller
Lightcloud Lightcloud Controlleroller20 0-10V Dimming 120V-277V B | Crescent Electric Supply Company
Contents Lightcloud Controller Instruction Manual Wire Nuts NPT Nut O-ring x 4 x 2 Specifications PART NUMBER LCCONTROL20/D10 INPUT 120-277VAC, 50/60Hz
Rablighting.com view install, tips setting
File Info : application/pdf, 14 Pages, 992.54KB
DocumentDocumentController LCCONTROL20/D10 WE'RE HERE TO HELP: 1 (844) LIGHTCLOUD 1 (844) 544-4825 support@lightcloud.com Hello The Lightcloud Controller is a remotely controlled switch and 0-10V dimming device. Product Features Wireless Control & Configuration Switching up to 20A 0-10V Dimming Power Monitoring Contents Lightcloud Controller NPT Nut O-ring Wire Nuts x 4 x 2 Instruction Manual Specifications PART NUMBER LCCONTROL20/D10 INPUT 120-277VAC, 50/60Hz <2W (Standby - 4W (Active) MAXIMUM SWITCHED LOAD RATINGS For Control of Magnetic, Electronic Ballast or LED 277VAC: 20A Magnetic/Resistive 240VAC: 5A Tungsten/Electronic, 20A FLA/ 60 LRA, 2HP 120VAC: 15A Tungsten/Electronic, 1HP OPERATING TEMPERATURE -40°C to +40°C OVERALL DIMENSIONS 1.55" diameter, 5.75" length 1/2" NPT Mount, Male 16AWG pigtails WIRELESS RANGE Line-of-Sight: 1000 feet Obstructions: 100 feet Class 2 IP66 Rated Indoor and Outdoor Rated Wet and Damp Location Plenum Rated What You Need Lightcloud Gateway A Lightcloud installation requires at least one Lightcloud Gateway to manage your devices. WE'RE HERE TO HELP: 1 (844) LIGHTCLOUD or 1 (844) 544-4825 support@lightcloud.com Wiring PANEL WHITE/RED RED WHITE BLACK LOAD BLACK / HOT WHITE / NEUTRAL PURPLE PINK WHITE BLACK PURPLE PINK 0-10V DIMMING Lightcloud Controller Setup & Installation 1 Turn Off Power WARNING OFF OFF 1a Find a Suitable Location Use these guidelines when installing devices: · If there is a clear line of sight between two Lightcloud devices, they can be placed up to 1000 feet apart. · If the two devices are separated by ordinary drywall construction, try to keep them within 100 ft. of each other. · Brick, concrete and steel construction may require additional Lightcloud devices to go around the obstruction. Add an additional Lightcloud Device to extend network range around corners DRYWALL OR SIMILAR LightcloudGateway <= 100 ft. BRICK, CONCRETE OR METAL WALL Setup & Installation (cont'd) 2 Install your Lightcloud Controller 2a Install at a Junction Box (Indoor/Outdoor) To Load BLACK To Panel WHITE BLACK Lightcloud® Controller RED PURPLE PINK To Driver/Ballast 0 - 10V DIMMING 0-10V is a common method of low-voltage control of dimmable drivers and ballasts. Purple: 0-10V positive | Pink: 0-10V common NOTE: The National Electrical Code requires that low-voltage wiring used in the same enclosure as high-voltage wiring have an equal or better insulation rating. You may need to complete your low-voltage wiring in another enclosure or use a partition. 2b At Lighting Panel or Trough WHITE BLACK Space and code allowing, you may install Lightcloud devices directly in your breaker box or lighting panel. Alternatively, break out lighting circuits and install Lightcloud devices in a separate trough. ! Controller requires constant, unswitched power. DO N 'T DO POWER POWER OFF When power switch is set to OFF C ontroller is disconnected from network LO AD Controller always has power and is connected to the network LO AD Setup & Installation (cont'd) 3 Labeling your Device When installing devices, it's important to keep track of their Device IDs, installation locations, panel/circuit #s, dimming function, and any additional notes. To organize this information, use the Lightcloud Installer Application (A) or Device Table (B). 3a Lightcloud Installer Application Install the LC Installer Application: LC Installer is available for iOS & Android. Scan & Install Lightcloud Devices: Scan each device and assign to a room. It's recommended that each device is scanned just before or just after being wired so no devices are missed. The more notes that are given, the easier it is to commission the system. Device Scanner PLACE RECTANGLE TO FIT CODE ON LABEL Enter Manually Device Info Device ID 0013A20040B62A4A Location Office Zone Name Office Lights Dimmable Power Monitoring Cancel Save Device Scanner PLACE RECTANGLE TO FIT CODE ON LABEL Enter Manually Devices Office Light - ID 0013A20040B62A4A Controller Office Light - ID 0013A20040B62A4B Sensor Office Light - ID 0013A20040B62A4C Dimmer Office Light - ID 0013A20040B62A4D Daylight Office Light - ID 0013A20040B62A4E Touch Send to RAB Add Device Scan Device Code Enter Device Information Repeat for Additional Devices Send to RAB 3b Device Table CONTROLLER DEVICE IDs 1 2 3 Your Site Name DEVICE ID 1 ZONE NAME Front Desk PANEL/ CIRCUIT # 2 DIMMING For setup and maintenance, we provide two Lightcloud Device Tables with the Gateway: one that you can attach to your panel and one to hand off to a building manager. Attach the Device Identification stickers included witheach device to a row, then write in additional information, such as Zone name, Panel/Circuit Number, and whether or not a zone uses dimming. Send to RAB: Once all of the devices have been added and organized, submit the information for commissioning. Lightcloud Controller 4 Power Up To add new devices to your Lightcloud network, call RAB at 1 (844) LIGHTCLOUD, or email us at support@lightcloud.com. 5 Confirm Device Connectivity Confirm Status Indicator is Solid Green (see details below) DEVICE IDENTIFICATION BUTTON · Illuminated when device is powered · Press once to highlight this device in the Lightcloud Application · Press twice to toggle circuit on and off · Press twice and hold to set dim level · Press and hold for 10 seconds to remove this device from a Lightcloud network · Blinks when device is indicated from the Lightcloud Application SIGNAL INDICATOR Illuminates when the device receives a message and indicates the strength of the signal. 3 - Best signal 2 - Acceptable signal 1 - Unacceptable signal Consult the "Finding a Location" section for more information. STATUS INDICATOR Solid GREEN when connected to your Lightcloud network. Blinking RED when not connected. The device will automatically continue trying to connect to a network in Setup Mode. 6 Commission your devices Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD Functionality Configuration To configure Lightcloud products, use the Web Application (control.lightcloud.com) or call 1(844) LIGHTCLOUD. WE'RE HERE TO HELP: 1 (844) LIGHTCLOUD or 1 (844) 544-4825 support@lightcloud.com Operating Modes CONTROLLER: Provides switching and dimming for a single zone. REPEATER: Extends the Lightcloud mesh network without controlling a load. TRIGGER: Detect when an attached circuit is open or closed. For example, you could attach the Controller in Trigger mode to an existing occupancy sensor to allow your Lightcloud system to react to the sensor. OCCUPANCY LOCAL: Use an attached sensor to control the Controllers load. OCCUPANCY CUSTOM: Use an attached sensor to control the load of any Zone in the Lightcloud site. ADVANCED TRIGGER: Designed to use a third-party occupancy sensor to detect occupancy without that sensor directly controlling the lights. Controller will function as an occupancy sensor in this mode. BLACK WHITE BLACK WHITE RED EXISTING OCCUPANCY SENSOR RED WHITE/RED RESLC/XXX WHITE BLACK WHITE/RED Lightcloud TM Controller RED PINK PURPLE WHITE LOAD RESLC/XXX, where XXX=120 for 12VAC applications or 277 for 277VAC applications. POWER MEASUREMENT: The Lightcloud Controller is capable of measuring the power usage of the attached circuit. POWER LOSS DETECTION: If mains power to the Controller is lost, the device will detect this and alert the Lightcloud application. EMERGENCY DEFAULT: If communication is lost, the Controller may optionally fall back to a specific state, such as turning the attached circuit on. Controller requires constant, unswitched power. Any wires not in use must be capped off or otherwise insulated. This product should ! only be installed by a qualified electrician and in compliance with local and national electrical codes. FCC Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This device has been tested and found to comply with the limits for Class A digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. To comply with the FCC's RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user's authority to operate this equipment. Lightcloud is a commercial wireless lighting control system. It's powerful and flexible, yet easy to use and install. Learn more at lightcloud.com 1 (844) LIGHTCLOUD 1 (844) 544-4825 support@lightcloud.com © 2022 RAB Lighting, Inc