Instruction Manual for COMELIT models including: IPSWP08N100A, Switch 8 Poe Ports 2 UPLINK 10-100, IPSWP08N100A Switch 8 Poe Ports 2 UPLINK 10-100, Switch, Poe Ports
IPSWP08N100A SWITCH 8 POE PORTS + 2 UPLINK 10/100 Please read this manual thoroughly before use and keep it for future reference Package Contents Check the following contents of your package: PoE Switch x 1 User Guide x1 Power Cord x1 Accessories(Rubber Feet*4) Hardware Description Front Panel DIP Switch Default: the factory default mode, can normal communication between port 1~10. VLAN: 1-8 port can be isolated each other but 1-8 port can connect to 9/10 port after open VLAN to stop broadcast Storm to increase forwarding rate of frame. CCTV Up to 250m PoE distance allows you to expand you network via Ethernet cable to where there is no power Line or outlet but where you want to fix device such as IP Cameras. - 1 - LED indicator LED PWR Color Green Function Off: No Power supply. Light: Indicates the switch has power. LNK/ACT Green Off: No device is connected to the corresponding port. Light: Indicates the link through that port is successfully Established at 10/100Mbps. Blink: Indicates that the Switch is actively sending or Receiving data over that port. Off: No PoE powered device (PD) connected. Light: There is a PoE PD connected to be port, which PoE Orange Supply power successfully. Blink: Indicates port abnormal power supply. Rear Panel The rear panel of the PoE Switch indicates an AC inlet power socket, which accepts input power from 100 to 240V AC, 50/60HZ. Power socket Connect the female connector of the power cord here, and the male connector to the AC(Alternating Current) power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage. Grounding column The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. Installation the Switch This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions in avoid of incorrect installation causing device damage and security threat. - 2 - Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet cloth or liquid; Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis; Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall; Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction; Make sure that the operating voltage is the same one labeled on the switch; Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks. Desktop Installation Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the device and the objects around it. Wall-mounted installation In the first two fixed screw on the wall as shown in the figure below Aim at the two fixed hole switches, and the machine smoothly on the screw - 3 - Turn on the switch Connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded ). When the switch is power on, the LED indicators flash for one second, which represents a resetting of the system. The Power LED indicator turns on green. Note: Please confirm the voltage is correct before power on, otherwise the switch will be damaged. (The power input is:100V-240Vac, 50/60Hz.) Specifications Model Standard Network Media MAC Address Table Transfer mode Frame Forward Rate Switching Capacity Dimensions (L*W*H) Fan Power Input PoE Port PoE Power on RJ45 PoE Power Output PoE Power Budget Temperature Humidity 8FEPoE+2FE IEEE802.3, IEEE802.3u ,IEEE802.3az, IEEE802.3x, IEEE802.3af, IEEE802.3at 10BASE-T: UTP category 3,4,5 cable (100m) 100BASE-TX: UTP category 5 cable (100m) 8K, Auto-learning, Auto-aging Store-and-Forward 10Base-T: 14881pps/Port 100Base-TX: 148810pps/Port 2G 220 *150*44mm 1*Fan AC: 100~240V, 50/60Hz Port1~8 Mode A 1/2(+),3/6(-) Voltage: 55V DC Power: 32W(Max) 120W Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F ) Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F ) Operating Humidity: 10% ~ 90% non-condensing Storage Humidity: 5% ~ 90% non-condensing - 4 -Microsoft Word 2016