TaylorPneumatic.com – Taylor Pneumatic Tool Company
Owner's Manual for Taylor models including: T-8816P 7 Angle Polisher, T-8816 7 Angle Sander, T-8816P 7 Inch Angle Polisher, T-8816 7 Inch Angle Polisher, T-8816 7 Inch Angle Sander, T-8816 7 Inch Angle Sander, 7 Inch Angle Sander, Sander, Polisher
TaylorPneumatic.com – Taylor Pneumatic Tool Company
T-7555 5" DA Sander 3/16" Orbit – Taylor Pneumatic Tool Company
T-7758RE 1/4" Extended Die Grinder - Rear Exhaust – Taylor Pneumatic Tool Company
File Info : application/pdf, 2 Pages, 2.27MB
DocumentDocumentT-8816P 7" Angle Polisher T-8816 7" Angle Sander OILING INSTRUCTIONS: 49 OIL AFTER EACH USE WITH 1/2 TEASPOON OF AIRTOOL OIL THROUGH THE AIR INLET. RUN FOR 1 SECOND TO COAT ALL INTERNAL PARTS 47 48 USE 90 PSI MAXIMUM Ref # Part # Description 1 881601 Plug 2 881602 Spindle 3 881603 Key 4 881604 Retaining Ring 5 881605 Bearing 6 881606 Cap Screw 7 881607 Washer 8 881608 Spindle Cap 9 8816P09 Bevel Gear - Polisher 9 881609 Bevel Gear - Sander 10 881610 Wave Washer 11 881611 Retaining Ring 12 881612 Spacer 13 881613 Motor Housing 14 881614 Handle 15 8816P15 Pinion Gear - Polisher 15 881615 Pinion Gear - Sander 16 881616 Front Plate 17 881617 Rotor 18 881618 Rotor Blades(4 to set) 19 881619 Cylinder 20 881620 Roll Pin 21 881621 Rear Plate 22 881622 O-Ring 23 881623 Motor Gasket 24 881624 Spacer 25 881625 Valve Gasket Qty. 1 1 1 1 1 4 8 1 1 1 1 1 1 1 1 1 1 1 1 1 set 1 1 1 1 1 1 1 Ref # 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Part # 881626 881627 881628 881629 881630 881631 881632 881633 881634 881635 881636 881637 881638 881639 881640 881641 881642 881643 881644 881645 881646 881647 48 T-7470A 49 T-7472 Description Cap Screw Valve Pin Locking Lever Stop Rod Housing Valve Seat Valve Pin Valve Valve Spring Exhaust Gasket Exhaust Retainer Exhaust Bushing O-Ring Inlet Bushing Wrench19MM Pin Spring Pin Spring Bearing Grease Fitting Bearing 7" Velcro Poly Pad 7" Rubber Pad (optional) 7-1/2" Wool Pad (optional) Qty. 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 505 N Railroad Ave. P.O. Box 1117 Boynton Beach, Florida 33435 SEE OUR CATALOG at www.taylorpneumatic.com 0116TPTC /all rights reserved /COPYRIGHT 2016 / final PH. 561-732-1111 FAX 561-731-4412 TOLL FREE 800-805-8665 General Instructions Sanders T-6778 and T-7778 OIL AFTER EACH USE WITH 1/2 TABLESPOON OF AIRTOOL OIL THROUGH THE AIR INLET. RUN FOR ONE SECOND TO COAT ALL INTERNAL PARTS. IMPORTANT WARNING: WHEN RUNNING SANDERS, ALWAYS KEEP THE SANDPAPER ON THE WORK SURFACE. USE 90 PSI MAX. 22. SANDER SANDING PADS WITH A MAXI- 23. 24. 505 N. Railroad Ave. 33435 P.O. Box 1117 33425 Boynton Beach, Florida LIMITED!LIFETIME!WARRANTY Most products of Taylor Pneumatic are warranted to be free from defects in material and workmanship for the life of the tool. This warranty applies to the original purchaser only. This warranty does not cover tools that have been abused, misused, modified, not properly lubricated or to normal wear and tear. Taylor Pneumatic will at its option repair or replace the defective product free of charge except for shipping. Taylor Pneumatics sole liability and your exclusive remedy under this warranty is limited to the repair or replacement of the defective product. There are no other warranties expressed or implied and Taylor Pneumatic shall not be liable for incidental, consequential, or special damages, expenses or costs except as described above. WARRANTY!VOID!IF!TOOL!IS!DISASSEMBLED. Return tools to Taylor Pneumatic. Be sure to include your name, address, proof of pur- chase, and description of the suspected defect. This warranty applies to the basic tool. It does not apply to wear and tear on accessories or consumables such as drill chucks, backing pads for sanders, punch and dies for nibblers, spray gun cups, or accessories from a kit. SEE OUR CATALOG at www.taylorpneumatic.com Ph. (561) 732-1111 Fax (561) 731-4412 07/14 TPTCDPT all rights reserved Toll Free 800C-O8PY0RI5GH-T82061465