User Manual for darklab models including: airbolt mini Machine Batter, airbolt, airbolt mini, Machine Batter, Battery Power Supply
Xion S Gunmetal Elite Set | Microbeau International
Xion S | PMU Machine | Spektra | Any PMU Needles | Microbeau | Microbeau International
File Info : application/pdf, 10 Pages, 1.93MB
DocumentDocumentMachine Battery USER MANUAL FK Irons, Airbolt 5-12VDC 1A 2021 INDEX Safety Notice 3 Intro 4 Overview 5 Features 6 Getting Started 7 Additional Information 8 Troubleshooting 9 USER MANUAL SAFETY NOTICE CLASS III SYMBOL A Class III appliance is designed to be supplied from a separate/safety extralow voltage (SELV) power source. The voltage from a SELV supply is low enough that under normal conditions a person can safely come into contact with it, without the risk of electrical shock. The extra safety features built into Class I and Class II appliances are, therefore, not required. For medical devices, compliance with Class III is not considered sufficient protection, and further more-stringent regulations apply to such equipment. TECHNICAL DATA Operating Voltage: Current: Ambient Temperature: Relative Humidity: Dimensions (Ø X L): Weight: Charging Port: 5-12 V DC UP TO 1.0 A +10 to +35 °C 30 to 75% H56 x W49 X L27 mm Approx. 58g (2oz) USB-C BARRIER PROTECTING YOUR MACHINE We strongly suggest the use of barrier products to protect your machine. For a visual demonstration of barrier protection methods, please visit our YouTube channel FK Irons. This device is only for use by trained tattoo artists and not for the use by children or persons of reduced physical, sensory or mental capabilities. 3 USER MANUAL AIRBOLT INTRO THE AIRBOLT / AIRBOLT MINI Unleash Your Power The first wireless battery featuring complete Bluetooth connectivity, and a whole new sense of freedom. 4 USER MANUAL OVERVIEW LED Indicator Voltage Guide Control Buttons USB-C Port Bluetooth Enabled: Pair with Darklab app Compact Battery Housing Dynamic Power Path Management USB-C Li-ion Battery 1/4" (6mm) jack 55.6 mm SPECIFICATIONS 3.4oz · Output Voltage: 5 12 V · Increment/decrement voltage interval: 0.5 V · Maximum output current: 1.0 A · Charger Input: USB-C · Size: H56mm x W49mm x L27mm · Weight: Airbolt 121g (4.2 oz) Airbolt Mini 96g (3.4 oz) · Battery life: Up to 10 hours*, depending on usage *Range will vary based on, but not limited to, cartridge, stroke, voltage, needle Grouping, motor, and pigment viscosity. 4.2oz 73 mm The device should only be recharged with a USB Approved/Certified Class 2 Power unit charger marked 5 Vdc, 2000mA 5 USER MANUAL FEATURES Features: · Higher energy density to provide high reliability and stability · Dynamic power path management: USB-C Li-Ion battery · Auto shutdown (State of Charge (SoC) < 3%) · Automatic jumpstart feature · Fast charging speed: up to 1.0 A · Extremely compact, convenient to carry · Compatible with FK Irons and Darklab products · Bluetooth enabled, pair with Darklab app · Device firmware update functionality via app · Shipping mode functionality · Software reset Compatible with all FK Irons Spektra RCA machines, as well as most RCA machines on the market. 6 USER MANUAL GETTING STARTED For your safety, this power unit has been shipped disabled. To activate, plug into a USB-C power source and charge completely until the LED light remains solid green. It's important to charge for a minimum of 3 hours prior to first use. USB-C INPUT:5V 1A OUTPU T:5-12V 1A DISASSEMBLYWILL VOID WARRANTY MADE IN USA BY FK IRONS INC LED indicator Voltage Up Power Button Voltage Down LED Indicator: Solid color = Whole Value Blinking color = Half Increment Ex. Solid green indicates 10V Flashing green indicates 10.5V Battery Level Check: Press and hold power button until white. On release color = % Note: LED flashes while battery charges. Once < 15% is reached, a red light will blink alternately with voltage. 100 - 98% 97 - 60% 59 - 40% 39 - 15% 14 - 0% Automatic Fault Detection: Overcharge Detection (OVP) Over-Discharge Detection (UVP) Charge Overcurrent Detection (OCC) Discharge Overcurrent Detection (OCD) Load Short-Circuit Detection (SCP) Menu Modes: Press and hold power button. Hard shut off: Hold the power button until the LED indicator is red, battery is now disabled. To re-activate the battery, plug into any USB-C power source. Device reset: 7 USER MANUAL eGIVE eGIVE ADJUSTMENT With this feature you'll be able to control the amount of "give" or resistance of the needle upon impact with the skin. This enables the artist to take advantage of the softness or hardness of hit to achieve specific results. 0 no effect, 5 maximum amount of eGive. SETTING eGIVE There are 6 settings for eGive, 0 through 5. Change the setting by swipping down and up on the bars. The higher the setting the higher the amount of give. 0 = no give, 5 = maximum give. eGIVE INDICATOR The number displayed is the current eGive setting. 8 USER MANUAL ADDITIONAL INFORMATION VOLTAGE PARAMETERS While voltage is a parameter that will vary from artist to artist, the Airbolt/Airbolt Mini have been tested to operate at a minimum voltage of around 5-Volts with a maximum voltage of 12-Volts. Depending on the type of needle configuration, or brand you use, feel free to adjust the voltage to obtain the desired performance. NOTE: Some machines require a minimum voltage to operate correctly, please check your machine manufacturer's requirements. WARRANTY Darklab warrants that the device will perform efficiently when used as intended. Should this product prove to be defective due to manufacturing issues, Darklab will repair/replace the device - free of charge. This warranty will be void if the device shows signs of having been tampered, disassembled, handled roughly, dropped, overexposed to moisture or damage resulting in compromised functionality. HANDY TIPS The following tips will help you get the most out of your AirBolt/Airbolt Mini and avoid potential issues: · For the Xion mini do not exceed 10 volts. · Use only quality cables. A good connection will ensure consistent performance. · Use only FDA-approved cold sterilization solutions for disinfection. · NOT AUTOCLAVABLE. 9 USER MANUAL ADDITIONAL INFORMATION TROUBLESHOOTING 1.- Machine Manufacturer FK Irons: 1771 NW 79th Avenue, Doral, Florida 33126 2.- Servicing Your Machine As for any mechanical device, FK Irons strongly suggests that you service your device once a year to ensure all working parts are working as expected. This ensures the optimal condition of all working parts including internal machine clean up and fresh lubrication. Routine servicing will ensure that your machine remains functioning like the very first day. Service is subject to fees. 3.- Warning Disconnect machine from any power before making any adjustments. For service inquiries, please contact service@fkirons.com. For additional tips and tutorials, please visit Youtube.com/fkirons 10