User Guide for Shenzhen Longzhiyuan Technology models including: S-09G, S09G, 2AFCB-S-09G, 2AFCBS09G, LY-138 Battery WiFi Camera, Battery WiFi Camera
Shenzhen Longzhiyuan Technology Co., Ltd. S-09G Wireless Camera 2AFCB-S-09G 2AFCBS09G s 09g
280x100mm User's Guide for Battery WiFi Camera Product Features 2x18650 batteries work regularly for 2~4 months FHD Megapixels collocated with wide-angle lens Support mobile phone remote fast wake-up within 6 second 2.4G Wi-Fi connection Support PIR motion detection, when someone hovers at the door, it will send push alerts to your mobile phone immediately With IR-cut, it can switch automatically and it is clearly visible at both day and night to keep your home and family safe Support to power by USB port Product Specication Sheet Lens Infrared LEDs PIR Motion Sensor Storage Connectivity Power consumption Battery USB Wi-Fi distance Video Compression Voice Intercom Video resolution Working Temperature Storage Temperature FOV/130°Wide-angle lens (4Glass) 10 pcs Infrared LEDs with 8 meters ash distance 4~6 meters PIR distance Up to 128GB Micro SD card 802.11b/g/n Wi-Fi@2.4G Standby 200uA Working 260mA 2x18650 batteries DC5V 60 meters (open space without obstacle)15 meters (indoor) H.264 Two-way audio with noise cancellation 1920*1080@15fps -10~ 55 -20~ 60 Product Design Lens Mic Light sensor LED Motion detection sensor Charge LED USB interface Speaker Charge LED: Charging in Red; Full in Green. 18650 Reset button Mirco-SD card Power button 18650 Battery Flip Switch Install your camera Step 1: Please put the ip switch to "open"position and open the cover, then Install 18650 battery and Mirco-SD. (Please notice the polarity of the battery). Press the Reset button long until you hear the "system reset" prompt from the camera speaker. Step 2: Install anchors (on stucco, brick or concrete) On stucco, brick or concrete, use the bit to drill one holes in your wall, and install the anchors.install the base bracket on the wall Step 3: Align the device to the base bracket and hold it, then adjust the appropriate angle, the installation is nished Notes: 1. USB interface is only used as power supply. 2. The mobile phone connects to the Wi-Fi of the home router, and the mobile APP can generate a QR code that made of router Wi-Fi name and password. The product recognizes the QR code through the lens on the product, and the product is automatically connected to the router and server after identication. At this time, the APP also nds the product through the server, and the APP can control the operation of the product through the network. Note: Please notice the polarity of the battery. Please full charge this camera before using it for the rst time. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Corel PDF Engine Version 17.1.0.572