User Manual for superbrightleds models including: MWP Series, Mini LED Wall Pack
Mini LED Wall Pack Important: Read all instructions prior to installation. MWP Series User Manual Wall and Conduit Installation Instructions Rev Date: V2 03/31/2021 Rev Date: V2 03/31/2021
20W LED Mini Wall Pack - 2,500 Lumens - 70W Metal Halide Equivalent - 5000K/4000K | Super Bright LEDs
User Manual Important: Read all instructions prior to installation. Mini LED Wall Pack 5.33in 135.48mm 2.90in 73.72mm Wall and Conduit Installation Instructions MWP Series 84in 4mm 1. Remove power from circuit. 2. Remove 8.61in 218.81mm 2 plastic thumb screws from both sides of the light. Remove mounting bracket 5.05in 128.19mm from light. Peel adhesive film from Foam Gasket and stick to mounting bracket, while lining up the cut-outs. 4.84in 122.94mm 3. Drill 2 holes on the wall using bracket as a guide for holes. Drive wall anchors into holes. Attach mounting bracket to wall using 2 screws (not provided). 4. Remove knockout from bottom of light. Pull wires from conduit through knockout and make wire connections to main supply. Attach conduit onto light. 5. Attach light to bracket and tighten 2 plastic thumb screws. Mini LED Wall Pack MWP Series User Manual Rev Date: V2 03/31/2021 Rev Date: V2 03/31/2021 Important: Read all instructions prior to installation. Mini LED Wall Pack Included Parts 1 - Mini LED Wall Pack 1 - Foam Gasket Specifications MWP-40K20 / MWP-40K20-S / MWP-50K20 / MWP-50K20-S IP Rating IP65 Operating Temperature -4°113° F(-20°45° C) Weight 1.8 lb (0.8 kg) Check product label for specific electrical specifications related to installation. Improper installation will void warranty. Wire Diagram 120277 VAC Input Line Black LL Neutral White NN Ground Green GND GND Mounting Bracket Dimensions 3.94in 100mm .66in 16.80mm .20in 4.96mm Rev Date: V2 03/31/2021 User Manual MWP Series Safety and Notes · Product should be installed and serviced in accordance with applicable national, state, .84in 21.34mm and local building and electrical codes. · To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures. · Avoid looking directly into lamp when illuminated. · Ensure all mounts are securely attached and will support the weight of the fixture. Failure to properly support fixture may result in damage or injury, for which the manufacturer does not assume responsibility. 3.46in 87.88mm 2.72in 69.08mm 1.25in 31.75mm .74in 18.80mm 1.23in 31.24mm 5.13in 130.18mm User Manual Important: Read all instructions prior to installation. Mini LED Wall Pack 5.33in 2.90in 135.48mm J-Box Installation73I.7n2mmstructions MWP Series 1. Remove power from circuit. 2. Remove 2 plastic thumb screws from both sides of the light. Remove 8.61in mounting 218.81mm bracket from light. Peel adhesive film from Foam Gasket and 5.05in stick to mounting 128.19mm bracket, lining up the cut-outs. 4.84in 122.94mm 3. Mount bracket to J-box with 2 screws (not included). Pull wires from J-box through bracket. 4. Use slots to temporarily hang light on mounting bracket to J-box. Make wire connections to main supply. Push connected wires through bracket into J-box. Note: Wire connections can stay within light. 5. Mount light on bracket. Secure with 2 plastic thumb screws on both sides. Rev Date: V2 03/31/2021Adobe PDF Library 15.0 Adobe InDesign 16.1 (Windows)