GE LED 150 7MM Lights
Model No. 22043LO
For Indoor Use Only
Important Safety Instructions
When using electrical products, basic precautions should always be followed, including:
- Read and follow all safety instructions.
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. For outdoor applications, connect to a Ground Fault Circuit Interrupting (GFCI) outlet. Contact a qualified electrician if a GFCI outlet is not provided.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar heat sources.
- Do not secure wiring with staples or nails, or place on sharp hooks or nails.
- Do not let lamps rest on the supply cord or any wire.
- Unplug the product when leaving the house, retiring for the night, or if left unattended.
- This is an electric product – not a toy! To avoid risk of fire, burns, personal injury, and electric shock, it should not be played with or placed where small children can reach it.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from the cord, wire, or light string.
- Do not close doors or windows on the product or extension cords, as this may damage wire insulation.
- Do not cover the product with cloth, paper, or any material not part of the product when in use.
- This product is equipped with push-in type lamps. Do not twist lamps.
- Read and follow all instructions on the product or provided with the product.
Save these instructions.
Use and Care Instructions
- When placed on a live tree, the tree should be well-maintained and fresh. Do not place on live trees with brown or easily breakable needles. Keep the tree holder filled with water.
- If placed on a tree, the tree should be well secured and stable.
- Before using or reusing, inspect the product carefully. Discard any products with cut, damaged, or frayed wire insulation or cords, cracks in lampholders or enclosures, loose connections, or exposed copper wire.
- When storing the product, carefully remove it from its placement (tree, branches, bushes) to avoid undue strain on conductors, connections, and wires.
- When not in use, store neatly in a cool, dry location protected from sunlight.
User Servicing Instructions: Replace the Lamp
Follow these steps to replace a lamp:
- Grasp the plug and remove it from the receptacle or outlet device. Do not unplug by pulling the cord.
- Pull the lamp and plastic base straight out of the lampholder.
- Replace the lamp with only a 3.3 Volt, 0.066 Watt, LED type lamp (provided with the product).
If the new lamp base does not fit the lampholder, follow these steps:
- Remove the base of the burned-out lamp by straightening the lamp leads and gently pulling the lamp out.
- Thread the leads of the new lamp through the holes in the old base, with one lead in each hole.
- After the lamp is fully inserted into the base, bend each lead up, like other lamps in the light set, so the leads touch the contacts inside the lampholder.
Diagram Description: The process involves unplugging the light set, removing the old lamp and base from the lampholder, and inserting a new LED lamp with its leads correctly positioned to touch the lampholder contacts.
Caution
- Replace lamps only with 3.3 volt, 0.066 watt spare lamps provided with this product.
- Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Do not replace lamps with other than the spare lamps provided with this product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Troubleshooting
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| If the product does not light | One or more of the based LEDs may have loosened from the socket during transporting. There is a break in the circuit between the LED leads and the socket terminals. Male/female connectors not fully inserted together. Non-working control box. Foot pedal in off position. | Unplug the set at the outlet. Starting with the first unlit LED, gently push (don't twist) each LED base firmly into the socket. If still does not light, then remove each based LED and check for out-of-place lead wires. Make certain connectors are fully inserted and the securing cap is fully tightened. Step on foot pedal to turn LEDs on. |
| If a based LED is missing | One or more of the based bulbs may have come out of the socket when transporting. | Mark socket(s) with a piece of tape and unplug the set. Replace the based LED or use one of the spare based LEDs included with product. |
| If an LED fails to light (shorts or opens) | Incorrect LED, premature LED failure, or voltage is too high. | The LED may be out or dimly lit. Replace bad LEDs as soon as you find them. |
| LEDs fail to switch from white to multi | If applicable, then a defective control box or color change foot pedal. | Contact Customer Support. |
Contact Information
For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.geholidaylighting.com.
©2022 Nicolas Holiday Limited. FP-22 Printed in China.
246 Spring Hill Road, Unit B, Trumbull CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560
All rights reserved.
GE is a trademark of General Electric Company and is under license by Nicolas Holiday Limited.
The home for holiday lighting
