Onn ONA21DP001A 9-inch Portable DVD Player User Manual

Important Safety Instructions

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE: The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [High Voltage Warning Symbol]

ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [Important Information Symbol]

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Before using the unit, read all operating instructions carefully. Note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna.

1. Read these instructions: All safety and operating instructions should be read before the appliance is operated.
2. Keep these instructions: The safety and operating instructions should be kept for future reference.
3. Heed all warnings: All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow all instructions: All operation and use instructions should be followed.
5. Do not use this apparatus near water: The appliance should not be used near water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
6. Clean only with dry cloth: The appliance should be cleaned only as recommended by the manufacturer.
7. Do not block any ventilation openings: Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet and in the back or bottom are provided for ventilation to ensure reliable operation and protect from overheating. These openings must not be blocked or covered. Never block openings by placing the product on a bed, sofa, rug, or similar surface. Never place near or over a radiator or heat source. Do not place in a built-in installation, such as a bookcase or rack, unless proper ventilation is provided or manufacturer's instructions have been adhered to.
8. Do not install near any heat sources: Such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug: A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide or third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord: Prevent it from being walked on or pinched, particularly at plugs, convenience receptacles, and where it exits the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. [Portable Cart Warning Symbol]
13. Unplug this apparatus during lightning storms or when unused for long periods of time: To protect your product from a lightning storm, or when left unattended and unused for long periods, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage due to lightning and power-line surges.

Safety Instructions (Continued)

14. Refer all servicing to qualified service personnel: Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Power source: Operate this product only from the type of power source indicated on the marking label. If unsure of your home's power supply type, consult your appliance dealer or local power company. For products intended to operate from battery power or other sources, refer to the operation instructions.
16. Power lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
17. Overloading: Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
18. Object and liquid entry: Never push objects of any kind into the product through openings, as they may touch dangerous voltage points or short out parts, resulting in fire or electric shock. Never spill or spray any type of liquid on the product.
19. Service: Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Replacement parts: When replacement parts are required, ensure the service technician uses replacement parts specified by the manufacturer or those with the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
21. Safety check: Upon completion of any service or repairs, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

NOTE: Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way, such as the power-supply cord or plug being damaged, liquid spilled into the unit, the unit exposed to rain or moisture, the unit dropped, or the unit not operating normally.

Minimum 20cm distances around the apparatus for sufficient ventilation.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

Attention should be drawn to the environmental aspects of battery disposal.

The apparatus shall be used in moderate climates.

Warning:

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
• To avoid battery subjected to extremely low air pressure.
• The mains plug of the power adapter is used as the disconnect device. The socket outlet shall be installed near the equipment and shall be easily accessible.
• The USB port does not support USB charging for external circuit.
• The maximum operation temperature is 40°C.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Location of Controls

Function Panel View:

Diagram Description: A top-down view of the player's control panel. Numbered buttons are indicated:

1. MENU: Press to enter root menu. SOURCE: Press and hold to switch to "AV IN" mode, press and hold again to resume.
2. VOL +: Press to increase volume. SETUP: Press and hold to enter set up menu.
3. VOL -: Press to decrease volume. STOP: Press and hold to pre-stop playing, press and hold again to stop playing completely.
4. Navigation Buttons: Includes directional arrows (Up, Down, Left, Right) for navigation and track skipping, and fast forward/backward. Also includes Play/Pause (II) and OK buttons.
   • Up Arrow: Press to turn upward.
   • Previous Track Arrow (<<): Press to skip to previous track.
   • Down Arrow: Press to turn downward.
   • Next Track Arrow (>>): Press to skip to next track.
   • Left Arrow: Press to turn left.
   • Fast Backward Arrow (<<): Press to fast backward.
   • Right Arrow: Press to turn right.
   • Fast Forward Arrow (>>): Press to fast forward.
   • Play/Pause (II): Press to start playing or pause, press again to resume during playing.
   • OK: Press to confirm the operations.
5. OPEN: Press to open the disc door.

Location of Controls (Continued)

Right Side View:

Diagram Description: A view of the right side of the player showing various ports and controls.

• 6. USB Port
• 7. SD/MMC/CARD Slot
• 8. EARPHONE Jack
• 9. AV OUT Jack
• 10. AV IN Jack
• 11. POWER ON/OFF Switch
• 12. DC IN Jack

Front Side View:

Diagram Description: A view of the front of the player showing indicators and a sensor.

• 13. CHARGE Indicator
• 14. Remote Sensor
• 15. POWER Indicator

Remote Control

Diagram Description: An illustration of the remote control with numbered buttons.

• 1. POWER Button
• 2. VOLUME +/- Buttons
• 3. MUTE Button
• 4. MENU Button
• 5. Direction Buttons (Up, Down, Left, Right)
• 6. Skip Forward Button (>>): Press to skip forward.
• 7. Fast Forward Button (>>): Press to fast forward.
• 8. Play/Pause Button (II): Press to start playing or pause.
• 9. USB/CARD Button
• 10. TITLE Button
• 11. STOP Button: Press to stop playback.
• 12. AUDIO Button
• 13. GOTO Button
• 14. REPEAT Button
• 15. SLOW Button
• 16. LCD ON/OFF Button
• 17. Numeric Buttons (0-9)
• 18. SETUP Button
• 19. Skip Backward Button (<<): Press to skip backward.
• 20. Fast Backward Button (<<): Press to fast backward.
• 21. OSD (On Screen Display) Button
• 22. SUBTITLE Button
• 23. ANGLE Button
• 24. PROG (Program) Button
• 25. OK Button
• 26. STEP Button
• 27. ZOOM Button
• 28. A-B Repeat Button

Battery Installation (Remote Control)

Battery installation:

1. Press the tab on the battery door and lift it off.
2. Install two (2) x AAA size batteries into the battery compartment, observing the polarity markings inside the compartment. [Diagram showing AAA batteries being inserted into a compartment with correct polarity indicated].
3. Replace the battery door.

Battery Precautions:

• Use only the size and type of battery specified.
• Avoid replacement of a battery with an incorrect type.
• Ensure correct polarity when installing the battery. A reversed battery may cause damage to the device.
• Do not mix different types of batteries (e.g., Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the batteries are consumed or the device is not to be used for a long period, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended for recharging; they can overheat and rupture. Follow battery manufacturer's directions.
• Do not dispose of batteries in fire or a hot oven, or by mechanically crushing or cutting.
• Do not leave batteries in extremely high temperature surrounding environments.
• Avoid battery exposure to extremely low air pressure.
• Clean the battery contacts and those of the device prior to battery installation.

Remote Control Sensor:

Diagram Description: Shows the front of the player with the IR remote sensor. Indicates an effective range of 15 Feet (5M) and a reception angle of 30° left and 30° right.

Remarks:

• When there is an obstacle between the unit and the transmitter, the transmitter may not operate.
• When direct sunlight, an incandescent lamp, fluorescent lamp, or any other strong light shines on the remote control of the unit, the remote operation may be unstable.

Power Source

Charging by supplied AC/DC Adaptor:

1. Connect the small plug from the supplied AC/DC Adaptor to the DC IN Jack on the right side of the unit.
2. Connect the AC/DC Adaptor to the wall outlet (AC 100-240V~, 50/60Hz).
3. During charging, the red indicator will light, and it will turn green when finished charging.

Notes: For saving energy, unplug the AC/DC Adaptor from the wall outlet if the unit will not be used for a long period of time.

Your battery will last longer if you follow these simple guidelines for caring and storing it:

• A. Do not overcharge (longer than 24 hours). Excessive charging or discharging may shorten the battery's life.
• B. Battery life naturally shortens slowly over time.
• C. The rechargeable battery incorporated in this product is not user replaceable.

Charging by the supplied Car Adaptor:

1. Connect to the cigarette lighter socket of a vehicle that has a 12V battery. [Diagram showing a car adapter plugged into a cigarette lighter socket and connected to the unit's DC IN jack]. It is not compatible with a vehicle that has a 24V battery.
2. This is a special negative grounded Car Adapter. Using this Car Adapter with a positive grounded car can cause malfunction.
3. Do NOT plug in the Car Adapter until the car ignition is turned on.
4. Disconnect the Car Adapter from the cigarette lighter and the unit after use.

Connections

Connecting to a TV or Video Player (such as DVD, VCR, DVR Players) with an AV connection cable.

Diagram Description: Shows the rear panel connections of the DVD player and how they connect to a TV and a Video Player using an AV cable. The player has ports for USB, SD/MMC CARD, EARPHONE, AV OUT, AV IN, and DC IN. The AV OUT ports are color-coded: Yellow for Video, White for Audio Left, and Red for Audio Right. These connect to the corresponding input jacks on a TV or Video Player.

NOTE:

• The default setting of the unit is AV Out. If connecting to an external Video Player (such as DVD, VCR, DVR Players...), press and hold the SOURCE button to set to AV IN mode ("AV IN" will appear on the screen), press and hold again to resume.
• Use the Earphone (not included) to listen privately.

Swivel Panel

The viewing angle of the swivel panel can be adjusted as desired:

Diagram Description: Four illustrations showing the swivel panel adjustment. Image 1 shows the panel slightly tilted forward. Image 2 shows the panel rotated 180 degrees. Image 3 shows the panel in a standard upright position. Image 4 shows the player closed.

Operations

1. Lift up the panel and turn to the desired angle. Slide the Power ON/OFF switch to "ON" to power on the unit; the green indicator on the front of the player will light.
2. Press the OPEN button to open the disc door. Place the disc on the center spindle with the label side facing up. Close the disc door; the player will start playback automatically. If this does not occur, press the Play/Pause (II) button.
3. During playback:
   • Press the Skip Forward (>>) or Skip Backward (<<) buttons on the remote control repeatedly to fast search forward/backward.
   • Press the Play/Pause (II) button on the remote control to resume normal playback.
   • Press the Next Track (>>) or Previous Track (<<) buttons on the remote control repeatedly to skip to a specific track or chapter.
   • Press the Play/Pause (II) button on the remote control to pause; press the Play/Pause (II) button again to resume normal playback.
   • Press the VOL +/- buttons on the remote control to adjust the volume level.
   • Press the STOP button on the remote control to pre-stop. The player will remember the point where the disc was stopped. When the Play/Pause (II) button is pressed again, playback will start from that point. Press the STOP button twice to stop completely; press the Play/Pause (II) button to start from the beginning.
4. For saving energy, always power off the player by sliding the Power ON/OFF switch to the OFF position or unplugging the wall power adapter from the player and wall outlet.

Repeat Playback: (DVD)

• Press the REPEAT button once: the current chapter will playback repeatedly and continuously.
• Press the REPEAT button twice: the current Title will playback repeatedly and continuously.
• Press the REPEAT button a third time: all files will playback repeatedly and continuously.
• Press the REPEAT button repeatedly to turn off the repeat mode.

Repeat Playback: (CD)

• Press the REPEAT button once: the current track will playback repeatedly and continuously.
• Press the REPEAT button twice: all tracks on the disc will playback repeatedly and continuously.
• Press the REPEAT button repeatedly to turn off the repeat mode.

(CD/DVD) Program:

1. During CD or DVD playback, press the PROG (Program) button.
2. Using the Direction, OK, and Numeric buttons, select and set the desired Title (T), Chapters (C), or tracks (for CD) of the movie/music you want. The Program menu will appear as follows. [Diagram Description: Shows the program selection interface for DVD with Title/Chapter columns and CD with Track list].
3. Using the Direction buttons, select and highlight the "CLEAR" or "+" button on the screen, then press the OK button to clear all programmed items if there is wrong programming.
4. Using the Direction buttons, select and highlight the "PLAY" or Play button on the screen, then press the OK button to start program playback.

Operations (Continued)

• LCD ON/OFF: Press to turn the LCD display on or off.
• POWER: Press to turn to standby mode. Press again to turn on.
• Volume +/-: Press to increase or decrease volume.
• MUTE: Press to turn off the sound; press again to resume.
• MENU: Press to return to the disc's menu page (function depends on the recording of the disc).
• OSD (On Screen Display): During playback, press repeatedly to read the information of playback status.
• SUBTITLE: During DVD playback, press repeatedly to select the desired subtitle (function depends on the recording of the disc).
• STEP: During movie playback, press repeatedly to play the movie frame by frame. Press the Play/Pause (II) button to resume normal playback.
• TITLE: Press to return to the disc's title page (function depends on the recording of the disc).
• ANGLE: During DVD playback, press repeatedly to select the viewing angle (function depends on the recording of the disc).
• ZOOM: During movie playback, press the ZOOM button repeatedly to zoom in/out the picture. When in zoom in mode, press Direction buttons to select parts of the zoomed picture to watch (this function is not available on all discs).
• GOTO:
  • For DVD discs: Press to display the Title (TT), Chapter (CH), and time selection. Input the desired title, chapter, or playback time. Press the OK button to confirm.
  • For audio CD discs: Press to display the Track (TRK) and time selection. Input the desired track or playback time. Press the OK button to confirm.
• AUDIO:
  • During DVD playback, press repeatedly to select the desired audio language (function depends on the recording of the disc).
  • During CD playback, press repeatedly to select the desired audio channel (function depends on the recording of the disc).
• A-B Repeat: During playback, press the A-B button to define the start point of a section. Press the A-B button again to define the end point. The unit will then play the selected section repeatedly and continuously. Press the A-B button again to resume normal playback (this function is not available on all discs).
• SLOW: During playback, press the SLOW button repeatedly to set the slow motion speed. Press the Play/Pause (II) button to resume normal playback.

USB or SD/MMC Card Playback

1. Insert the USB device or SD/MMC memory card into the USB port/card slot. [Diagram Description: Shows the USB port and SD/MMC card slot on the player].
2. Note: The unit supports playback of MP3 (Music files) and JPG (Pictures). Make sure correct files are saved in the USB device or memory cards.
3. In Power ON mode, press the USB/CARD button on the remote control. A "DVD, CARD, USB" selection window will pop up on the screen. Use the Direction buttons to select and highlight the source, then press the OK button to confirm. Use the Direction and OK buttons to select the desired Folder or File, then press the OK button to start playback.
4. During playback:
   • Press the Skip Forward (>>) or Skip Backward (<<) buttons on the remote control repeatedly to skip backward/forward.
   • Press the Fast Forward (>>) or Fast Backward (<<) buttons on the remote control repeatedly for fast searching backward/forward.
   • Press the Play/Pause (II) button to pause. Press again to resume normal playback.
   • Press the STOP button on the remote control to return to the menu.

System Setup

Press the SETUP button on the remote control or press and hold the SETUP button on the unit. The setting menu will appear on the screen. During setting, use the Direction buttons (Up, Down, Left, Right) to select and highlight the function to set or reset, then press the OK button to confirm. After setting, press the SETUP button to save and exit.

SYSTEM SETUP Menu:

• TV System: Can be set to NTSC, PAL, or AUTO to match the connected TV.
• POWER RESUME: If set to On, the unit will start playback from the position where the disc was stopped last time.
• Screen Saver: If set to On, the screen saver will activate when the unit is idle or the image is paused for several minutes.
• TV Type: Set the aspect ratio to match the connected TV.
• Video: Use the Direction and OK buttons to set it to CVBS to match the connected TV.
• Default: Select to restore all settings to factory default.

LANGUAGE SETUP:

• Osd Language (On Screen Display Language): Use the Direction and OK buttons to set the priority of the available language (function depends on the recording of the disc).
• Audio Lang (Audio Language): Use the Direction and OK buttons to set the priority of the available language.
• Subtitle Lang (Subtitle Language): Use the Direction and OK buttons to set the priority of the available language or set it off.
• Menu Lang (Menu Language): Use the Direction and OK buttons to set the priority of the available language of the on-screen menu.

RATING SETUP:

Diagram Description: Shows the Rating Setup menu with options for Password and Rating.

1. Password: Press the button to highlight the password field, then enter the default password "0000" to unlock the rating, and press the OK button to confirm. The lock status will be displayed. To change a password, highlight the password column, enter a new four-digit password, and press the OK button to confirm.
2. Rating: After unlocking, press the button to enter the rating level. Use the Up/Down or Left/Right buttons to select the desired rating level, then press the OK button to confirm the setting.

Rate levels:

• KID SAFE: Kid safe
• G: All ages
• PG: Parental Guidance
• PG 13: Parental Guidance less than 13 years old
• PG-R: Under 17 years old, Parental Guidance suggested
• R: Under 17 years old, Parental Guidance strongly
• NC-17: 17 years old or above
• ADULT: Adult only

TFT SETUP:

Use the Direction and OK buttons to set or reset picture quality such as Brightness, Contrast, Hue, and Saturation.

DIGITAL SETUP:

• Dual Mono: Use the Direction and OK buttons to set it to Stereo, Mono L (Plays Left channel on all speakers), Mono R (Plays Right channel on all speakers), or Mix Mono (Mixed Right and Left channel then plays on all speakers) as desired (functions depend on the recording of the disc).
• Downmix: Use the Direction and OK buttons to set it to LT/RT or Stereo as desired.
  • If set to LT/RT, the rear left and rear right channels will play on both Left and Right Speakers.
  • If set to Stereo, the rear left channel will play on the Left Speaker, and the rear right channel will play on the Right Speaker.
• Dynamic Range: Use the Direction and OK buttons to set the dynamic level or turn it off.

Care and Maintenance

Caring for Discs:

Treat the disc carefully. Handle the disc only by its edges. Never allow your fingers to contact the shiny, unprinted side of the disc.

• Do not attach adhesive tape, stickers, etc., to the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents or abrasive cleaners. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck, it is probably dirty or damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the outer edge. Never wipe in circular motions. [Diagram Description: Shows a disc being wiped from the center outwards with a cloth, and bottles of cleaner].
• Store discs in their cases after each use to avoid damage.
• Do not expose discs to direct sunlight, high temperatures, or dust. Prolonged exposure or extreme temperatures can warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing instruments or ink may damage the surface.

Cleaning the Unit:

• To prevent fire or shock hazard, disconnect the unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for like other furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.

Troubleshooting

Check the followings before requesting service:

Symbols

Specifications

Power adapter information:

Caution: Please refer for further information to the user manual. Use only power supplies listed in the user instructions.

• Manufacturer: SHENZHEN SHI GUANGKAIYUAN TECHNOLOGY., LTD.
• Commercial Registration No.: 91440300053998927W
• Address: 2 floor, 41 TianSheng Road, TianLiao village, GongMing Street, Guangming, Shenzhen, Guangdong, P.R. China
• Model No.: GKYZA0100120UK
• Input: 100-240V~ 50/60Hz 0.5A
• Output: 12.0V = 1.0A 12.0W
• Average active efficiency: 84.08%
• No-load power consumption: 0.042W
• Efficiency at low load (10%): 81.58%

Disc Compatibility: DVD/SVCD/DVCD/CD/CD-R/CD-RW/DVD±R/DVD±RW

ACCESSORIES:

• 1 x User's Manual
• 1 x Power Adapter
• 1 x Car Adapter
• 1 x Remote Control
• 2 x AAA Batteries

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE!

Guarantee and Support

Free 1 year guarantee:

All electrical items are covered by a full 1-year guarantee from the day of purchase. In the unlikely event that your product is faulty or you are struggling to set it up, here's what to do:

1. If you experience any problems, please contact the technical help line, which will be happy to help. Please note this is not a freephone number.
2. If the problem cannot be resolved, you will receive a reference number.
3. Take the reference number, along with the item, all its components, and your receipt to your nearest store for a full refund.

Need something else?

There are a wide range of accessories and other products that can be ordered direct to your door. For more information, see www.asda.com.

Declaration of Conformity and Recycling

Hereby, declares that the radio equipment type Onn DVD is in compliance with Directive 2014/35/EU, 2014/30/EU.

The full EU declaration of conformity is available at the following internet address: http://www.asda.com

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

Users have the choice to give their product to a competent recycling organization or to the retailer when they buy a new electrical or electronic equipment.

Manufacturer Address: ASDA, Leeds LS11 5AD/ASDA, Antrim BT41 4GY