CommScope | now meets nextWireless Support
Installation Guide for COMMSCOPE models including: F4-HMHM-2M-SGWB-D HELIAX SureGuard V2.0 Weatherproofing System, F4-HMHM-2M-SGWB-D, HELIAX SureGuard V2.0 Weatherproofing System, SureGuard V2.0 Weatherproofing System, Weatherproofing System, System
F4-HMHM-2M-SGWB-D | CommScope
File Info : application/pdf, 2 Pages, 533.72KB
DocumentDocumentInstallation Instructions HELIAX® SureGuard V2.0 Weatherproofing System for 1/2" SureFlex ® Bird-Proofing Jumpers For 4.3-10 Male Connectors, Connectors to Female Device Ports U.S. Patent 9,216,530 and other patents pending Bulletin 7837732 Revision B Materials Page 1 of 2 Tools fectiveness. CommScope Infrastructure Academy offers installation training. CABLE SIZE 1/2 in CABLE TYPE FSJ4 INTERFACE TYPE 4.3-10 DEVICE PORT DIAMETER 17.50 - 24.50 mm (0.689 - 0.965 in) (Just for Ericsson RRU 4415) 4.3-10 Boot For E4415 4.3-10 Cap Torque Wrench TOOL PART NUMBER DESCRIPTION TW-4310 Torque wrench for coupling torque of 4.3-10 connectors, 22 mm opening Installation temperature range -40 ºC to +65 ºC (-40 ºF to +149 ºF) 1 Torque the 4.3-10 connector using 2 the appropriate wrench. Scan for Installation video's Push from the b2ack of the boot up towards the RRU connector from one side of the boot. Opposite side is where the power and FO cables are located. 3 Push forward and backward the boot several times to ensure it has past over the RRU connector neck. 4 Twist and push up the swollen part of the boot severial times until the boot stretches to cover the female neck. 5 Keep twisting and pushing up until the boot is fully extended to reach the connector base of the RRU and the connector is covered 360degrees uniformly. Installation Instructions HELIAX® SureGuard V2.0 Weatherproofing System for 1/2" SureFlex® Bird-Proofing Jumpers For 4.3-10 Male Connectors Connectors to Female Device Ports U.S. Patent 9,216,530 and other patents pending Bulletin 7837732 Revision B Page 2 of 2 CommScope Infrastructure Academy offers installation training. 6 Push the gasket through the cable and stopped by boot end face as shown. 7 Push the conduit and stopped by gasket and ensure conduit is fully cover the gasket. 8 Push cap to cover the boot in and keep the cap as line as boot. 9 Screwed cable gland nut by hand as shown. 10 Completed. 11 Do not hold the connector and bend the cable directly behind it, start bend 30mm min away from the cap end as picture shown. R50mm min 30mm min REWORK: Pull back gasket along with conduit, then pull back sureguard V2.0 CommScope 1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339 (828) 324-2200 (800) 982-1708 www.commscope.com Technical Support +1 888 297 6433, Option 3 (Toll Free US and Canada) +1 828 323 4220, Option 3 (local) https://www.commscope.com/wisupport (open a ticket) Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro. Avis : CommScope décline toute responsabilité pour les conséquences de procédures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses. Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten. Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de instalação, inspeção, manutenção ou remoção. Avvertenza: CommScope declina eventuali responsabilità derivanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure. © 2020 CommScope