Instructions for OPTONICA models including: 6391 4 Ways DMX Signal Splitter, 6391, 4 Ways DMX Signal Splitter
DMX Signal Amplifier | OptonicaLED
2 days ago — 3 years. Protection. Reverse Polarity. Warranty. Operation temperature. Case temperature (Max.) Environment. IP20. IP rating. Ta: -30 OC 55OC. T c: 65OC.
2 giorni fa — Technical Parameters. Warranty and Protection. 3 years. Protection. Reverse Polarity. Warranty. Operation temperature. Case temperature (Max.) Environment. IP20.
4 Ways DMX Signal Splitter SKU: 6391 Input and output optical isolation/Four independent outputs/DMX512-A compatible LVD Features One DMX512 signal input, repeat four DMX512 signal output, each allowing for 32 DMX devices to be connected. Dedicated to amplify, distribute and insulate the signal that comes from the lighting system equipment when it is connected to the bus of DMX512(or RS-485). Photo-electricity insulation between input and output terminals, output terminals among channels. Input isolated from outputs to 500VAC, 1000VDC. Outputs are isolated from each other to 500VAC, 1000VDC. Input and outputs are ture RS-485 rated, and no microprocessors are used for maximum reliability. 3 pin XLR / 3 screw terminals input and loop through, 5 pin XLR option available. 6 front panel LEDs indicate power in, DMX in and DMX output status at each output. Technical Parameters Input and Output Input voltage Input current IOnpuuttpsuigt nsiagl nal Output signal 12-36VDC 0.5A Max. DMX512 x 2 DMX512 x 4 Environment Operation temperature Case temperature (Max.) IP rating Ta: -30 OC ~ +55 OC T c: +65OC IP20 Safety and EMC EMC standard (EMC) Safety standard(LVD) Certification EN55032:2015, EN61000-3-2:2014, EN61000-3-2:2013, EN55024 :2010/A1:2015 EN 61347-1:2015 EN 61347-2-11:2015 CE,EMC,LVD Warranty and Protection Warranty 3 years Protection Reverse Polarity Mechanical Structures and Installations DC socket DMX512 Power input input DMX512 through 1-4 XLR3 DMX512 output Installation rack INPUT 12-36VDC DMX IN DMX THRU DMX OUT1 DMX OUT2 DMX OUT3 DMX OUT4 4 Ways DMX Signal Splitter 1 DMX signal input and 4 independent DMX signal output Input signal and output signal is isolated Output signal and output signal is isolated INPUT 12-36VDC V+ DMX IN D+ D- GND DMX THRU D+ D- GND Power SignalIn SignalOut 1 2 3 4 DMX OUT1 D+ D- GND DMX OUT2 D+ D- GND DMX OUT3 D+ D- GND DMX OUT4 D+ D- GND Power input DMX512 DMX512 input through LED indicator Dimension 1-4 screw terminals DMX512 output 256.00 mm 38.00 mm 92.00 mm Page 1 DMX Wiring Diagram DMX 512 Mater DMX DMX DMX DMX Signal Splitter Device 1 Device 2 Device 3 Device 4 Device 31 Device 32 Terminated Device 1 Device 2 Device 3 Device 4 Device 5 Device 32 Terminated Device 1 Device 2 Device 3 Device 4 Device 5 Device 32 Terminated Note: 1. A passive loop-through connection allows onward connection to other DMX512 devices. If this feature is not required then the signal must be terminated. 2. Each output is capable of driving 32 additional DMX512 devices. It is not necessary to terminate any outputs that are not connected. However, a terminator must be connected to the final DMX512 device. 3. Connect 0.25W 90-120 terminal resistor for termination. IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72; Page 2Corel PDF Engine Version 16.1.0.843